Search Results

This 3-speed blower switch controls the exhaust fan in your range hood, allowing you to select low, medium, or high airflow. Replacing a worn switch can restore dependable ventilation and proper speed control. What it does:

• Selects low, medium, or high fan speed by routing power to the blower motor
• Helps resolve a fan that will not run, runs only on one speed, or will not change speeds
• Can address a switch that feels loose, sticks, or works intermittently

• 1 three-speed blower switch

• Disconnect power at the breaker before servicing
• Access the control area; note wire locations (or take a photo) and transfer wires to the new switch one at a time
• Ensure push-on terminals are fully seated and secure
• Test all fan speeds before reassembly

Color: Black. Instruction sheet included.

Fix washer temperature issues with a new selector switch. Solves problems when hot or cold water won't flow correctly or temperature settings don't respond.

This wiring harness connects the appliance's electrical components to restore reliable power and signal routing. It replaces a damaged or worn harness to help resolve power loss and intermittent electrical issues. What it does:

• Transfers power and control signals between components so controls and motors can operate
• Replaces frayed, burned, or broken wiring that can cause intermittent operation
• Helps stop failures that lead to no-start or loss of specific functions
• Restores secure connector fit to reduce arcing or poor connections

• Always disconnect power before servicing the appliance
• Match connectors and wire routing to the original harness; avoid stretching or pinching wires
• Secure fasteners and strain reliefs; verify all connections are fully seated
• If you find heat or burn damage at terminals, inspect adjacent components for root cause

Color: White

If your washer won't fill, overfills, or leaks water everywhere, the water level pressure switch may have failed. DIY fix in 15 minutes or less.

Replacement switch harness that connects a cooktop or range surface element switch to the appliance wiring, restoring secure electrical connections so burners heat reliably and reduce intermittent or unsafe operation. What it does:

• Carries power between the surface element (infinite) switch and the cooktop element or terminal block.
• Restores reliable heating when a damaged harness causes intermittent or no heat.
• Replaces frayed, burned, or corroded wiring that can cause arcing, sparking, or a burning smell.
• Keeps connector terminals secure to prevent loose connections and erratic element behavior.

• Disconnect all power (unplug range or shut off circuit breaker) before starting any work.
• Make secure, fully seated connections; avoid pinched or kinked wires and route harness clear of heat sources.

Fixes burner that won't heat or stays on one temperature. This infinite switch restores variable heat control to your cooktop surface element.

Fix burners stuck on high or won't adjust temperature with this selector switch. Restores reliable control of cooktop functions. Moderate DIY repair.

Oven won't start or stop correctly? A faulty micro switch prevents proper sensing of linked mechanisms. This switch restores accurate control signals.

Burner stuck on high heat? This dual infinite switch kit restores adjustable temperature control on electric cooktops. Moderate DIY, 1-2 hours.

Burner won't heat or stays on constantly? This infinite switch restores variable heat control to your cooktop element. Moderate DIY repair.

This 3-position temperature switch selects the dryer's heat level so the appliance reaches the desired drying temperature. It replaces a worn or faulty selector to restore proper temperature selection and consistent drying performance. What it does:

• Switches between three temperature settings to control dryer heat levels.
• Routes power to the heater circuit based on the selected heat setting.
• Commonly replaces a switch that causes incorrect heat, no heat on some settings, or inability to change temperature.
• Works with the dryer's control system and thermostats to maintain selected drying temperature.

• Disconnect power to the appliance before attempting any service.
• Handle terminals and connectors carefully; match wiring to original locations or take a photo before removal.
• Verify operation with a multimeter for continuity per service manual before and after installation.

This switch assembly restores dependable control of your range hood or ventilation unit, helping resolve unresponsive or intermittent controls so the appliance turns on, off, and changes settings as expected.

• Provides the user interface to turn functions on/off and change settings
• Failure signs include no response on certain settings, intermittent operation, or a stuck/loose actuator
• Heat, moisture, and normal wear can degrade internal switch contacts over time
• Replacing the switch restores smooth, consistent operation

• Disconnect power at the breaker before servicing
• Access the control area and photograph wiring to document positions
• Move wires one at a time to the new switch; ensure tight, fully seated connections
• Reassemble and test all functions before finalizing

Burner won't turn on or heat settings won't change? This control switch sail assembly restores the actuator that engages your range's control switch.

This control switch activates the surface-burner spark ignition when you turn the knob to Lite. Replacing a worn switch restores consistent lighting and can stop unwanted, continuous clicking caused by a stuck switch. What it does:

• Closes the ignition circuit to the spark module to light a surface burner when the knob is turned
• Typical symptoms: no spark from a specific knob, intermittent ignition, or continuous clicking with knobs in the Off position
• Heat, spills, and moisture intrusion can damage the switch over time

• 1 control switch

• Disconnect power and shut off gas; allow the appliance to cool before servicing
• Remove the knob and front/top panel as needed to access the switch on the burner valve
• Transfer wires one at a time to the new switch; mount in the same orientation and secure
• Restore power and gas; test for proper spark at each burner before reassembly