Valve

After tracing the water dripping back up through the inside of the washer I found the water dispenser inlet valve was leaking. I watched several videos to make sure I understood what was involved. I contacted a local parts company to get the part. I also searched online for the part. I found that AppliancePartsPros.com had it cheaper. I ordered late in the afternoon and it arrived the next day. It was fairly easy to installed and saved me a minimum of $99 "diagnostic" fee plus whatever the part... Read more

• Will not fill with water
• Will not stop filling with water

This should be plastered all over the place and every owner of a front end washer should be advised or a recall should be issued about this. As I opened the top of my washer to fix a F35 error by replacing the water level switch, which worked out great and it fixed the issue, I noticed a rusting spot at the bottom of the washer just under where the motor is placed. After running the washer with the lid open (I don't recommend doing that) I noticed that it was coming from the top of the soap... Read more

• overflowing

This was not my first rodeo have repaired our appliances and those of our daughters for years, have ordered parts from this site several times. We had a cold spell in Texas, as you may have heard. We weathered it okay but left the dishwasher closed on one of the colder nights, woke up to water on the floor in the kitchen. Turned off the supply line, shut off the dishwasher power, bailed out the bottom, and mopped up. Had a fair idea of what the cause was, checked a few websites, watched some... Read more

• Will not fill with water

First I cleared the food chopper area. There were things there, bits of plastic for instance, but it wasn't the reason for the dishes not getting sprayed off. The dishwasher continued to only partially fill and not circulate the water. I started the dishwasher, let the pump start and then opened the door and filled up the dishwasher manually. It sprayed water as it should, cleaning the top rack quite well. I figured the issue was not the float switch, since some water was coming in. So I... Read more

Replaced water inlet valve took all of 10 minutes and washer is filling great on hot and cold. Thanks to Appliance Parts Pros for getting me the part within 24 hours. I have a very happy customer. Read more

I found a youtube video about replacing the hot water valve in a Samsung washer. It looked pretty easy. I had been very satisfied with an earlier order from AppliancePartsPros.com, so I ordered this part on Sunday after 9PM, standard delivery, hoping to get the part by the end of the week. I was flabbergasted to receive the part TUESDAY MORNING! Wow! I followed the instructions in the youtube video exactly. It took around 15 minutes, because I was being very careful not to drop screws in... Read more

• No hot or cold water
• Will not stop filling with water

It was really easy to fix. I just took a screw driver and gently pried up on the top of the clothes washer to open up the top. Then the mixing valve was easy to access. I removed the two screws holding and unplugged the the wires. And pulled the old one free. Then reversed the process to install the old one. Less than thirty minutes start to finish. Read more

Replaced both hot and cold water inlet valves. Works like a charm, issue resolved. Read more

As a Mechanic, I did the common sense approach: INITIAL OBSERVATIONS & CHECKS: - Unplug Machine & check inlet water hose connections for leaks and signs of hose failure; - Remove back panel & inspect for water presence at all hose connections, pump, bottom of basket (bottom center of basket where the main motor, shaft bearing, and tub seal is located), dispensers, bottom of wash basket, water injector area, look everywhere where there is a hose connection and where water flows... - Inspect... Read more

• Ice maker not making ice
• Leaking

Replaced inlet water valve Read more

• No hot or cold water
• Will not fill with water
• Will not stop filling with water
• Noisy

1. Sleeve for input, Injector valve, nozzle and seal for input fixed this problem. Probably the main part that was the trouble was a deformed Injector Valve which is a rubber tube with an internal retention groove at the wide part that grips the Nozzle. The Sleeve and the Nozzle are hard plastic parts that basically looked fine, but I replaced them anyway while I was in there. Additionally I replaced the rubber Seal for Input which seals the plastic input fitting to the tub just to make sure... Read more

Replaced valve assembly- issue resolved. super easy to replace the part Read more

The tech sheet test 56 said the motor wouldn't return to zero. I ordered the "Ice Maker Assy-Lp, and the Valve Assy-Water Dual". On my particular model the ice maker is in the ceiling of the refrigerator box. After removing the water filter and two screws around the drop down water filter door, the right side panel drops down by pulling it apart from 3 plastic pop-ins. Two of them broke when the repair guy man handled it. Pulling easy and supporting the inside pieces is key. Then I unplugged... Read more

1.) Located where the water leak was coming from in the refrigerator. 2.) Unplugged the refrigerator. 3.) Shut off the water supply to the refrigerator. 4.) Unscrewed the back cardboard panel. 5.) Unscrewed the Water Valve attached to the side of the refrigerator (one screw). 6.) Disconnected the three electrical plugs on the water valve. The plugs are different sizes so there is no need to worry about reconnecting incorrectly. 7.) Disconnected the two water lines by pushing down on... Read more

• Will not fill with water
• Will not stop filling with water

The F20 code was low/no water pressure code. I watched a YouTube video and purchased a Water Inlet Valve from Appliance Pros. After my son installed the new part my washer still didn't work. I looked on Google for trouble shooting and the 1st thing it said was turn on both hot/cold water as the washer needs the pressure of the hot/cold water. I had turned off the hot valve because it was leaking. I assumed I could still do cold water loads. Read more

Replace the valve Read more