Douglas C Tiburon , CA September 09, 2017 Appliance: KitchenAid Hot Water Dispenser KHWS160VCR1 My hot water got very un hot Turned off the water supply, unplugged the heater, then used pliers to release the clamp on the plastic outlet tube. I had to cut the tubing when I couldn't get it to come off the metal pipe. Unscrewed the quick-connect copper supply tube. I could then lift the heater off the mounting bracket (no tools) and quickly pulled it out. Used plumber's wrench to unscrew the 9/16" drain plug over the sink to drain the water. Put the plug back in. Remove the thermostat knob by pulling, removed two screws holding the cover over the thermostat. Remove two screws on either side holding the unit's top on. You may have to clean the tubing gaskets to pull the top off. I had to cut the plastic tubing carefully off the outlet pipe where it had fused and hardened over the years before I could pull the top off. One end of the thermal link is right under the cover, pliers will remove easily. The other end goes to the bottom of the thermostat, also pulls off easily with pliers. Replace the part, reassemble the unit. Remount, reattach the tubes, do NOT plug in until you've used the sink knob to refill the internal reservoir with water or you'll just burn out the link again! Once filled, NOW plug it in, wait 15 minutes or so for it to heat, and you should be done, unless the thermostat was also faulty (I took a chance it was just the fuse to avoid the much greater cost of the thermostat unless necessary). The contacts sometimes arc over time, so this would be the next step, same disassembly required, just one nut that holds on the thermostat accessible behind that cover plate, with two push-on electrical connections. Read More... Do-It-Yourself Rating: Repair Time Estimate: 1-2 hours Tools: Pliers, Screwdrivers
Craig S Sammamish , WA February 17, 2015 Appliance: KitchenAid Water Dispenser KHWS160JCR2 Kitchenaid instant hot water dispenser no hot water I replaced the thermostat and thermo-fuse. Our KitchenAid instant hot water dispenser temperature setting started to become unstable heating and spitting out boiling water followed by no heat. I found that the contacts on the thermostat had become badly pitted leading up to a thermo-fuse failure. In the future if this happens I will file the contacts which will give me time to order a new thermostat before it burns out the thermo-fuse. The Thermostat is easy to access behind the front name plate so I don't even need to remove the dispenser from under the counter. If you do need to take out the entire tank to access the thermo-fuse wire, the hardest part is releasing the quick disconnect 1/4" copper tubing feeding water at the top. Trick:Push down on the plastic quick fit coupling using a 1/4" open end wrench fit around the tubing while gently pulling up on the copper tube. Read More... 20 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: 30-60 minutes Tools: Nut Drivers, Screwdrivers, Wrench Set
Steven S Newnan , GA July 28, 2015 Appliance: KitchenAid Hot Water Dispenser KHWS160VWH5 No hot water from instant hot water dispenser water also leaked from quick connector of spout tubing to the tank Researching your website, the most likely culprit was the thermostat and/or thermal fuse. I decided to replace both, in addition to a new quick-connector purchased at Lowe's. After unplugging the unit, I removed the quick-connector from the tank and used pliers to slide the clear tubing clamp up so as to remove the tube from the top of the tank. As long as one doesn't activate the OFF/ON cap at the spout it isn't necessary to turn off the cold water supply. Once the water lines are disconnected, I removed the unit and inverted it to rid it of trapped water. Two small screws secure the faceplate through which the temperature control extends, and that plate was removed to access the thermostat. I also removed two screws securing the top of the tank, which gives access to the thermal fuse's connection to one lug of the heating element. Utilizing a 5/16" nut driver, the thermostat can be removed and the two wires which attach to it are removed (spade connectors). Connect the appropriate end of the thermal fuse and reconnect the power wire to the new thermostat and reinstall. Reconnect the other end of the thermal fuse to the heating element lug, and the repair is complete. Install the tank top and temperature control panel and connect the two water lines, and you are good to go. Read More... 5 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: 30-60 minutes Tools: Nut Drivers, Pliers, Screwdrivers
Keith M Nacogdoches , TX September 11, 2017 Boiled over quit working Replaced the fuse,cleaned the contacts on the thermostat..works fine now! Read More... Do-It-Yourself Rating: Repair Time Estimate: 15-30 minutes Tools: Pliers, Screwdrivers
Michael K Boynton Beach , FL February 01, 2015 No hot water in kitchenaid instahot I installed the two parts...and it works! Read More... Do-It-Yourself Rating: Repair Time Estimate: 30-60 minutes Tools: Pliers, Screwdrivers