Parts for Gaggenau VG232-212CA: 01 - Burners & Grate Parts

Replacement burner cap that sits on the gas burner head to protect components and shape the flame for even cooking. Restores proper flame pattern and stovetop performance when the original cap is cracked, warped, or missing. What it does:

• Covers and protects the burner head from spills and debris.
• Helps shape and stabilize the burner flame for consistent heat.
• Promotes reliable ignition by providing the correct flame path.
• Commonly replaces caps that are cracked, warped, or causing uneven flames.

• Turn off the cooktop and gas supply and ensure all parts are completely cool before handling.
• Remove the old cap, clean the burner head of debris, then seat the new cap flat and centered on the burner head.
• No special tools typically required; verify correct fit before using the burner.

This replacement burner cap covers the cooktop burner to help shape and stabilize the gas flame for efficient cooking. It restores proper flame pattern and protects the burner head from spills and debris. What it does:

• Centers and shapes the gas flame for even heating across cookware
• Protects the burner head from food, grease and corrosion
• Helps prevent flame irregularities and poor ignition caused by a damaged or misplaced cap
• Compatible with the matching burner head and cap seating on the cooktop

• Turn off all power and gas to the appliance and allow the cooktop to cool before servicing
• Remove grates and lift off the old cap; set the new cap down so it sits flat and centered on the burner base
• Inspect the burner head for clogs or damage and clean gently if needed before installing the cap
• If you smell gas or the burner behaves unusually after installation, stop use.

This small rubber gasket seals and cushions an M4 fastener to help prevent leaks and reduce vibration at attachment points. It's a compact replacement part used where a watertight or vibration-damping seal is needed. What it does:

• Creates a seal around an M4 screw or bolt to help prevent water intrusion
• Cushions fasteners to reduce vibration, noise, and metal-on-metal wear
• Restores a tightened fastener's proper sealing surface when the original gasket is worn
• Helps maintain appliance integrity around panels, brackets, or connections

• Power off and unplug the appliance before starting any repair.
• Confirm the gasket's size matches the fastener and seating area before installation.
• Install flat against the mating surface; tighten fastener snugly but avoid over-torquing which can deform the gasket.
• Handle small parts carefully and retain any removed hardware for reassembly.

This burner tip directs gas flow to the burner for reliable ignition and steady flame patterns. It replaces a damaged or clogged tip to restore even heating and consistent burner performance. What it does:

• Guides the gas to the burner ports so the burner can ignite and burn evenly
• Helps maintain a consistent flame for proper cooking temperatures
• Can resolve symptoms like weak, uneven, or noisy flames when the tip is damaged or clogged
• Works with the burner assembly as the gas outlet component

• Inspect and clean the surrounding burner area before installation; ensure the appliance is fully disconnected from gas and power
• Hand-thread the tip to avoid cross-threading; tighten per manufacturer torque recommendations if available
• Use only on compatible burners as specified by the appliance manufacturer

This flange is the front mounting ring for a gas cooktop/range burner head, helping the burner cap seat correctly for an even flame and stable operation. It restores proper alignment and support for the burner assembly. What it does:

• Positions and secures the burner head and cap on the cooktop surface
• Helps ensure an even flame pattern and consistent cooking heat
• Prevents the burner cap from rocking or misaligning during use
• Supports correct burner-to-surface spacing for safe operation

• One flange, burner head (front)

• Turn off the gas supply and disconnect power before servicing the appliance
• Remove burner cap and head as directed by your appliance manual to access the flange
• Inspect surrounding gaskets or seals and replace if damaged; reinstall parts in correct order