Parts for Frigidaire PLKU1267DS0: 05 - Cabinet Parts

Screen - drain keeps the drain path clear by trapping lint and small debris before it reaches the pump or drain hose, helping reduce clogs and improve drainage. Simple replacement restores proper water flow and drain performance. What it does:

• Traps lint, hair and small debris to help prevent clogs in the drain path
• Helps maintain consistent water drainage and pump operation
• Replace if you notice slow draining, standing water, or visible debris at the drain opening
• Sits in the appliance's drain assembly to protect downstream components

• Disconnect power to the appliance before servicing; turn off the water supply if the model requires it
• Access the drain area per your model's service instructions (remove access panel or wash tub components as needed)
• Inspect surrounding seals and hoses for damage and clean mating surfaces before installing the new screen

The Handle is an OEM part for Frigidaire freezers. This handle is designed for easy and secure opening and closing of the freezer door, providing a firm grip for accessing the freezer compartment.

Over time, the freezer handle can become worn out or damaged due to frequent use, physical impact, or exposure to varying temperatures. Causes of a bad handle can include cracking, loosening of the attachment points, or discoloration.

Symptoms of a bad freezer handle include:

• The handle feeling loose or wobbly
• Cracks or breaks in the handle material
• Difficulty in opening or closing the freezer door
• The handle detaching from the door

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This hinge secures and allows controlled pivoting of a refrigerator door, restoring proper door alignment and smooth opening. It replaces a worn or damaged hinge to help the door close evenly and maintain a good seal. What it does:

• Supports the refrigerator door and maintains correct alignment
• Provides a smooth pivot point for opening and closing
• Helps ensure the door seals properly to preserve cooling efficiency
• Commonly replaced for symptoms like a sagging, sticking, or misaligned door

• Use proper tools and support the door during removal/installation to prevent damage or injury
• Disconnect power if working near electrical components; wear gloves and eye protection
• Tighten fasteners to manufacturer torque specs when available and check door alignment after installation

This drain hose carries water away from your appliance during draining to help prevent backups and leaks. Replace a cracked, clogged, or kinked hose to restore reliable water removal and protect surrounding floors and cabinets. What it does:

• Directs drain water from the outlet or pump to the designated discharge point
• Maintains proper flow; kinks or blockages can cause slow or no draining
• Helps prevent leaks from splits, pinholes, or loose connections
• Common signs: standing water, water under/around the unit, drain-related error codes, or odors

• Includes 1 drain hose

• Disconnect power and shut off water supply before servicing
• Place towels or a shallow pan to catch residual water when removing the old hose
• Note the original routing; seat connections fully, secure with clamps, and avoid sharp bends or kinks
• Run a brief drain/rinse and check all joints for leaks

This sleeve is a small spacer/bushing used in select Frigidaire-built appliances to keep mating parts aligned and moving smoothly. Replacing a worn sleeve helps eliminate play, reduce friction, and restore proper operation.

• Provides a guided, low-friction surface between parts that slide or rotate
• Maintains correct spacing/alignment to prevent wobble and rubbing
• Helps reduce wear on shafts, pins, or fasteners it interfaces with
• Typical symptoms: looseness or wobble, squeaking/scraping noises, uneven movement, or visible cracking/missing sleeve

• Disconnect power before servicing; shut off gas/water if applicable to your model
• Use your model's diagram to locate the sleeve and note orientation before removal
• Clean and inspect the mating shaft/pin or fastener; replace any severely worn components
• Seat the sleeve fully; avoid over-tightening hardware that passes through the sleeve

This replacement screw secures appliance components so brackets, shelves, trim, or panels stay firmly in place. Install a new screw when the original is missing, stripped, or corroded to restore a tight, rattle-free fit.

• Fastens brackets, panels, trim, or covers to the cabinet or liner
• Helps maintain alignment and reduce vibration and noise
• Direct replacement for a missing, rusted, or stripped fastener
• Use wherever your model's parts diagram specifies this screw

• Disconnect power before servicing; shut off water if working near water lines
• Match thread and length to the original location as shown in your model's parts diagram
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening (especially into plastic)
• Retain and transfer any original spacers or clips used with this fastener

This front roller is a replacement sliding wheel that supports the front of the appliance and lets the cabinet roll smoothly for repositioning or floor cleaning. Restores ease of movement and helps prevent floor damage from scraping. What it does:

• Replaces a worn or broken front roller that causes rough, noisy, or uneven rolling
• Restores smooth forward/backward movement when moving the appliance for cleaning or service
• Helps keep the appliance level at the front once adjusted
• Reduces scraping or catching on flooring from a damaged wheel

• One front roller

• Unplug the appliance or disconnect power before starting any service
• Tilt or raise the unit only as recommended by the manufacturer; use two people for heavy appliances
• Remove any trim or mounting screws securing the old roller and replace with the OEM roller and hardware
• Test movement and leveling after installation; retighten fasteners if needed

This caster nut secures an appliance caster or leveling wheel so the caster stays attached and the appliance rolls or levels properly. A small but essential fastener for caster stability and safe movement. What it does:

• Holds the caster assembly or wheel onto the appliance frame or bracket
• Prevents the caster from loosening or falling off during use or when moving the appliance
• Restores stable, even rolling or leveling when a worn or missing nut causes wobble
• Works with the caster stud/bolt to keep the wheel aligned and secure

• Disconnect power and water and move the appliance to a stable work area before servicing
• Support the appliance so it cannot tip while removing/installing the caster
• Use the correct size wrench or socket to avoid rounding the nut
• Replace damaged or stripped studs or casters if the nut will not secure properly

This is a rear roller mounting bolt that secures the refrigerator drawer/door roller assembly, helping the roller stay fixed for smooth, stable sliding and proper alignment. What it does:

• Fastens the rear roller/roller mount to the appliance frame or bracket
• Keeps the roller assembly aligned so drawers or doors slide evenly
• Can prevent rubbing, sagging, or uneven movement when properly secured
• Works as a single replacement fastener when the original bolt is missing or damaged

• One rear roller mounting bolt

• Hand-start the bolt to avoid cross-threading, then tighten securely without over-torquing
• If working near powered components, unplug the appliance or disconnect power first
• Wear gloves to protect hands from sharp edges and use appropriate tools for access