Parts for Thermador PRG364GL: 06 - Oven Convection Parts

This air duct directs dryer airflow from the drum to the external vent, helping remove moisture and lint for efficient drying. It's a direct-fit replacement that restores proper exhaust routing and reduces airflow restrictions. What it does:

• Channels hot, moist air from the dryer drum to the vent system
• Helps prevent lint buildup in the cabinet by keeping airflow on the correct path
• Supports stable drying performance and helps reduce extended cycle times caused by restricted airflow
• Compatible with factory mounting points and seal surfaces for a proper fit

• Disconnect power (and gas if applicable) before starting any repair.
• Inspect vent hose and adjacent seals; replace any damaged components for best performance.
• Tighten fasteners to OEM torque; avoid over-flexing the duct when reinstalling.
• Check external venting and lint trap/duct for obstructions.

This air duct directs dryer airflow from the drum to the external vent, helping remove moisture and lint for efficient drying. It's a direct-fit replacement that restores proper exhaust routing and reduces airflow restrictions. What it does:

• Channels hot, moist air from the dryer drum to the vent system
• Helps prevent lint buildup in the cabinet by keeping airflow on the correct path
• Supports stable drying performance and helps reduce extended cycle times caused by restricted airflow
• Compatible with factory mounting points and seal surfaces for a proper fit

• Disconnect power (and gas if applicable) before starting any repair.
• Inspect vent hose and adjacent seals; replace any damaged components for best performance.
• Tighten fasteners to OEM torque; avoid over-flexing the duct when reinstalling.
• Check external venting and lint trap/duct for obstructions.

This glow igniter heats electrically to light the appliance's gas burner. A weak or failed igniter can stop ignition or cause very long preheat times; replacing it restores reliable burner lighting and proper heating performance.

• Heats to a bright glow to ignite the gas burner
• Common fix for oven not heating or burner not lighting
• Often resolves long preheat times or intermittent ignition
• If the igniter doesn't glow—or glows but no flame appears—it may be weak or failed

• Disconnect power and shut off gas before servicing; allow the unit to cool completely
• Handle the ceramic element carefully; avoid touching the igniter surface and do not flex, drop, or strike it
• Transfer any reusable mounting hardware and wiring/connectors from the old part as needed
• Verify secure connections and proper positioning near the burner before restoring power and gas

Restore clear visibility inside your oven with this oven lamp assembly. It replaces a failed or damaged light unit so you can check cooking progress without opening the door and losing heat.

• Illuminates the oven cavity during baking and broiling
• Replaces a cracked lens, burned socket, or damaged lamp housing
• Can help fix a light that won't turn on, flickers, or is intermittent
• Maintains visibility without repeated door openings

• Disconnect power at the breaker and allow the oven to cool completely before service.
• Remove oven racks for working space; access the lamp area per your model's service instructions (from inside the cavity or the rear panel).
• Handle glass components carefully; if transferring a bulb, avoid touching the glass directly.
• Restore power and test the light before reinstalling racks and returning the oven to service.

This OEM replacement part is a motor assembly for ovens. The motor assembly is the main motor that powers the oven fan which is responsible for maintaining and adjusting the temperature in an oven. If the oven is no longer heating properly, turning on, or maintaining temperature, then the motor assembly will need to be replaced.To replace this part, make sure that the oven is unplugged. After it has been powered off, proceed to pull the oven out and away from the wall. Once moved, uninstall the back panel of the oven by removing the panel's mounting screws. After detaching the back panel, locate the motor housing on the back of the oven. Unthread the screws that hold the housing in place. Once removed, locate the mounting brackets that hold the motor in place and remove the screws that attach to the motor. Pull the old motor out of its place and install the new motor. Reinstall the back panel and restore power to the appliance.This genuine replacement part is sold individually and is compatible with Bosch, Gaggenau, and Thermador brand ovens.

This air duct directs dryer airflow from the drum to the external vent, helping remove moisture and lint for efficient drying. It's a direct-fit replacement that restores proper exhaust routing and reduces airflow restrictions. What it does:

• Channels hot, moist air from the dryer drum to the vent system
• Helps prevent lint buildup in the cabinet by keeping airflow on the correct path
• Supports stable drying performance and helps reduce extended cycle times caused by restricted airflow
• Compatible with factory mounting points and seal surfaces for a proper fit

• Disconnect power (and gas if applicable) before starting any repair.
• Inspect vent hose and adjacent seals; replace any damaged components for best performance.
• Tighten fasteners to OEM torque; avoid over-flexing the duct when reinstalling.
• Check external venting and lint trap/duct for obstructions.

This air duct directs dryer airflow from the drum to the external vent, helping remove moisture and lint for efficient drying. It's a direct-fit replacement that restores proper exhaust routing and reduces airflow restrictions. What it does:

• Channels hot, moist air from the dryer drum to the vent system
• Helps prevent lint buildup in the cabinet by keeping airflow on the correct path
• Supports stable drying performance and helps reduce extended cycle times caused by restricted airflow
• Compatible with factory mounting points and seal surfaces for a proper fit

• Disconnect power (and gas if applicable) before starting any repair.
• Inspect vent hose and adjacent seals; replace any damaged components for best performance.
• Tighten fasteners to OEM torque; avoid over-flexing the duct when reinstalling.
• Check external venting and lint trap/duct for obstructions.