Parts for Briggs & Stratton 128352-0049-E1: Air Cleaner, Exhaust System, Gear Reduction Parts

This oil seal is a common part engineered to work in engines that power generators, vacuum cleaners, snowblowers, leaf blowers, mowers, and other small engine applications. The seal sits between the crankcase and the crankshaft. It is designed as a barrier to prevent oil leakage and to stop contaminants from leaving the crankcase. When the gasoline engine exhibits diminished power, and especially if it begins to emit oily gray or bluish smoke, there is a good chance the oil seal needs to be replaced. In order to replace the faulty seal, begin by removing the starter housing and taking off the nut that holds the starter wheel to the main shaft. The user will find the old seal on this shaft. Remove it and install the new seal, pushing it into place with the edges of a socket, then tapping it securely into place with a hammer. When choosing a replacement seal, remember to use an OEM genuine replacement part that is guaranteed to match the specs for the original part. This will ensure a quality match and long replacement life. This seal is compatible with Toro, Lawn-Boy, and Briggs & Stratton engines.

This replacement exhaust gasket is an authentic OEM part for a snowblower or lawn tractor engine. On these appliances, the exhaust is located quite near to the air filter, meaning that there is a chance that exhaust could leak into the carburetor. The carburetor requires fresh air to oxygenate fuel for combustion, so manufacturers install a gasket to help seal off the exhaust. Once installed, gaskets exist under a lot of pressure and will absorb the heat of the engine. These stresses cause gaskets to slowly degrade and eventually break their seal. If the exhaust gasket blows, the engine will not perform as it should. Be cautious of a noisy engine that burns more fuel than usual and gives off a burning smell. These are signs that the exhaust gasket has given out. If so, use a socket wrench and wrench set to disassemble the blower and air filter housings, then remove the exhaust manifold and change out the broken gasket. This high-quality replacement exhaust gasket is compatible with engines made by Toro, Husqvarna, Briggs & Stratton, and Snapper. It comes sourced from the original manufacturer and ships individually.

This exhaust gasket is a genuine Midwest Engine replacement part for appliances that use small engines, such as chipper shredders, snowblowers, leaf blowers, and lawn mowers. The function of an exhaust gasket is to seal off the carburetor from the exhaust tube in order to protect the engine from the accumulation of dirt, debris, and gunk within the inner workings. The exhaust gasket may require replacement over time from general wear and tear. If the exhaust gasket is not sealing, allowing dirt and debris to accumulate within the carburetor and leaving the exhaust tube exposed, the part should be replaced immediately. Evidence of a damaged exhaust gasket could also manifest in the form of oil leakage, black smoke arising out of the exhaust tube, and unusually low pressure from the combustion when using the appliance. Any of these symptoms can be attributable to multiple factors, so one should assess if the exhaust gasket is responsible before ordering a replacement.This exhaust gasket is compatible with the following brands: Briggs and Stratton, Cub Cadet, Toro, and Simplicity. This part sold individually.

This genuine Midwest Engine foam pre-cleaner can be used as a replacement part for appliances operated by small engines, including lawn tractors, lawn mowers, snowblowers, leaf blowers, vacuums, and tillers. A foam pre-cleaner is an air filtration system made of a foam layer through which the air must pass before accessing the primary air filter. The purpose of a foam pre-cleaner is to put less stress and strain on the primary air filter, thereby requiring fewer primary air filter changes. The foam pre-cleaner in a small engine appliance should be cleaned once every 24 hours of appliance usage; if it is not cleaned regularly on this timetable, it is highly likely that it will have to be replaced after less than optimum hours of appliance usage. If the regular air filter has to be changed more than usual, it is likely that the current foam pre-cleaner has to be replaced as well. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This foam pre-cleaner is compatible with the following brands: Midwest Engine, Briggs & Stratton, Toro, and Simplicity.