Parts for Lg LW1213HR/00: Air Conditioner Parts

This clamp secures a line or connection inside your appliance, maintaining a tight fit under vibration. Replacing a fatigued clamp helps prevent leaks or disconnections and keeps components anchored so the system operates reliably.

• Holds a line/fitting firmly to keep the joint sealed and secure
• Helps prevent leaks or disconnections at hose/tube connections
• Resists vibration that can loosen fittings during operation
• Replace if bent, weakened, or corroded, or if the connection repeatedly loosens

• Disconnect power and, if applicable, shut off water supply before service
• Note clamp orientation and routing; seat the clamp just behind the fitting bead/stop
• Use the correct tool for your clamp style to compress or tighten evenly
• After reassembly, restore utilities and test for leaks or movement

This remote controller assembly is the complete handheld control used to operate compatible appliances, restoring lost or damaged remote control functions for convenient, wireless operation. What it does:

• Sends the appliance's infrared/remote commands to control settings and cycles
• Replaces a broken, unresponsive, or missing remote to regain full remote functionality
• Helps resolve symptoms like no response from remote, intermittent command reception, or damaged buttons
• Works as the user-facing control interface for selecting modes, temperatures, or timed functions

• One remote controller assembly (as shown)

• Replace with the power source removed and follow the appliance manual for pairing or setup
• Handle electronic components carefully; avoid moisture and static discharge
• If the original remote used batteries, install fresh batteries and test operation after replacement
• If commands still fail, verify line-of-sight to the appliance and that the appliance receiver is powered

This power cord assembly supplies mains power to your appliance and replaces a worn, damaged, or broken cord to restore reliable electrical connection. Designed to match the original cord form and plugged connection for a direct replacement. What it does

• Delivers AC power from the wall outlet to the appliance's inlet.
• Replaces frayed, cut, or heat-damaged cord that can cause intermittent power or no power.
• Restores a secure plug connection when the plug or wiring is loose or exposed.
• Helps prevent arcing and unsafe connections when the original cord is compromised.

• One power cord assembly.

• Always unplug the appliance or shut off power at the breaker before installing.
• Installation is typically a direct swap; route the cord and secure strain relief as original.
• Verify the cord's connector seats fully and that wiring matches the appliance inlet polarity.

The A/C Condenser Fan Blade is an OEM part for LG air conditioners. This fan blade is responsible for drawing air through the condenser coils to dissipate heat, ensuring the air conditioner operates efficiently and effectively.

Over time, the condenser fan blade can become damaged or worn out due to exposure to outdoor elements, debris, or physical impact. Additionally, regular use can lead to wear and tear, affecting the fan blade’s performance.

Symptoms of a bad A/C condenser fan blade include:

• Reduced cooling efficiency
• Unusual noises such as rattling or clanking from the fan area
• The fan not spinning or spinning unevenly
• The air conditioner frequently cycling on and off due to overheating

This OEM LG part is also compatible with Sears/Kenmore models.

This blower is the rotating wheel that moves air through the dryer to support proper drying and venting. Replacing a worn or damaged blower restores airflow for more efficient, consistent drying performance. What it does

• Spins to pull air from the drum through the heater and out the vent
• Restores normal airflow when a blower wheel is cracked, broken, or missing fins
• Helps reduce long dry times, overheating, or unusual noises caused by a failing blower
• Works with the dryer motor and housing to maintain proper ventilation

• One blower wheel

• Disconnect power to the dryer before starting any repair
• Access typically requires removing the dryer front or rear panel and detaching the drum or blower housing
• Inspect the motor shaft and mounting hardware; replace any worn fasteners or bearings as needed

This isolator routes microwave energy between the magnetron and waveguide to help protect components and maintain consistent heating performance. Replacing a failed isolator can restore reliable cooking and help prevent further high-voltage damage. What it does:

• Directs RF energy from the magnetron into the waveguide/cavity
• Helps protect the magnetron by reducing reflected energy
• Aids in preventing arcing or burn damage in the waveguide area
• Common symptoms of failure: no heat or uneven heating, loud humming/buzzing, visible arcing/burn marks near the waveguide

• 1 isolator

• Disconnect power and discharge the high-voltage capacitor before servicing; risk of electric shock
• Handle waveguide components carefully; avoid contaminating RF surfaces and note exact orientation
• Take photos of the original setup to match positioning and fastener locations

The Thermistor Assembly is an OEM part for LG air conditioners. It is typically located near the evaporator coil or in the air intake area of the unit. It measures the ambient temperature and sends signals to the control board to adjust the cooling output accordingly.

Causes of a faulty or malfunctioning thermistor assembly can include normal wear and tear, exposure to extreme temperatures, or electrical issues. These factors can lead to inaccurate temperature readings, improper cooling performance, or erratic behavior of the air conditioner.

Symptoms of a bad thermistor assembly may include:

• Inconsistent cooling or insufficient cooling
• Inaccurate temperature display on the control panel
• Frequent cycling on and off of the compressor

This OEM LG part can also be used on Kenmore/Sears appliances. 

Replace a missing or damaged installation kit with this Install Part Assembly. Designed for select air conditioners, it helps secure and seal the unit during setup for a stable fit and reliable performance.

• Provides the correct mounting/finishing components needed for proper installation
• Helps seal the opening to minimize air leaks and reduce vibration/noise
• Restores secure, stable support of the chassis during and after install
• Symptoms indicating replacement: incomplete installation, loose fit, rattling, or drafts around the unit

• Disconnect power before beginning; use two people to lift and support the unit
• Follow the model's installation instructions carefully
• Inspect the opening/sleeve; install level and tighten all fasteners securely
• After installation, verify a tight perimeter seal and stable, rattle-free operation