Parts for Thermador PDR364GDZS/06: Pc Board / Ignitor Parts

The Oven Control Board is an OEM part for Bosch ranges and ovens that controls the power supply and operation of your oven. It receives signals from the control panel and relays the appropriate power to various heating elements and components, allowing you to cook.

A bad control board can occur due to electrical surges, component failure, or internal malfunctions. Signs of a faulty board include power irregularities, error codes, or unresponsive controls.

Symptoms of a bad control board include:

• Oven not turning on or heating 
• Unresponsive or erratic control panel 
• Error codes displayed 

Replace your malfunctioning control board with this genuine OEM Bosch part to restore your oven. This Bosch part can also be used on Thermador and Gaggenau appliances.
 

This OEM replacement pin is a small hardware fastener used to secure or pivot mating components within the appliance. Replacing a worn or missing pin restores proper alignment and reliable movement of the affected part or linkage.

• Serves as an axle/retainer for hinges, brackets, or linkages
• Maintains alignment of moving parts to reduce wobble or binding
• When bent, worn, or missing, you may notice looseness, rattling, misalignment, or difficulty opening/closing related components
• Direct-fit OEM replacement for the specified application

• Disconnect electrical power and shut off water or gas before servicing
• Support the component being serviced to prevent strain or damage during removal/installation
• Note the original orientation and retain any washers, clips, or spacers for transfer to the new pin
• Inspect mating holes/bushings; replace related worn parts to ensure proper fit and operation

This is a quality spark re-igniter module for stoves, ranges, and ovens. This part is located between the cooktop on the stove. This part creates a spark to ignite a low-pressure gas flow that goes to the flame pilot light. It will stay lit until the thermostatic control on the oven is turned to the off position.Sometimes, the spark re-igniter will become damaged or stop working, which can cause problems using the range. If there is a weak or nonexistent spark between the igniter pin and the edge of the gas burner, this is a sign the spark re-igniter needs to be replaced. The first thing to do is unplug the stove from the wall. Access the back of the stove and remove the large panel. Remove the original component and install the new one in its place.This is an authentic OEM replacement part that has been obtained directly from the manufacturer. The spark re-igniter module is sold as a single part. It is made to be compatible with Bosch and Thermador stoves and ranges.

The Simmer Control is an OEM component specifically designed for Bosch ranges. It regulates gas flow to provide the lowest possible flame setting needed for delicate cooking tasks. Precise control allows for uniform, attentive simmering.

Symptoms of a bad simmer control include inconsistent or unadjustable flame heights on low settings. Cracks, damage, or wear of internal mechanisms over time can also cause unstable flame control.

Causes of bad simmer control can be normal wear and tear issues like dirt buildup impeding mechanisms. Accidental impact or overheating leading to cracks are other causes for replacement.

Symptoms of a bad simmer control include:

• Flames that surge or fluctuate below the lowest settings   
• Inability to adjust the flame down sufficiently low
• Burners that shut off or cause overflow flooding on low-heat  

This OEM Bosch part is also compatible with Thermador and some Kenmore ranges. Replace for dependable, Fine-tuned low-heat performance.
 

This ignition device generates the spark needed to light gas burners, restoring reliable ignition and preventing continuous clicking or no-light conditions. Replace a failed module to re-establish normal burner ignition. What it does:

• Sends high-voltage sparks to the burner electrodes to ignite the gas flame
• Replaces a faulty spark generator when burners won't light or there is no visible spark
• Stops continuous clicking or rapid sparking caused by a failing ignition module
• Works as the central control for timed spark output to each burner electrode

• Disconnect electrical power and shut off the gas supply before starting any work
• Remove the oven/range access panel and note wire locations or take a photo to ensure correct reconnection
• Handle the electrode and module carefully to avoid bending or contaminating the spark tip

The Ignition Device is an OEM part for Bosch ranges and ovens. Located near each gas burner, the ignition device provides the critical spark needed to light the burners during startup. 

Causes of a bad ignition device can include wear from prolonged use over many years. Mineral buildup or debris accumulation may also prevent the spark from jumping across.

Symptoms of a bad ignition device include:

• Burners failing to light or staying lit
• Repeated attempts needed to ignite the gas  
• Inconsistent flame heights or burner performance
• Fault codes or error messages displayed

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models. 

This Wire is an OEM part for Bosch ranges. As an essential component of the appliance's electrical system, this wire ensures secure connections between various electrical components within the range. Its durable construction and precise design contribute to reliable power distribution and safe operation.

A common issue with a faulty Wire involves wear and tear over time, leading to wire fraying, exposure, or damage. Exposure to heat or physical strain can also compromise its integrity, potentially causing electrical malfunctions within the range.

Symptoms of a malfunctioning Wire may include:

• Inconsistent power supply to the range
• Non-functional heating elements or components
• Visible damage, such as fraying or exposed wires

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.