Parts for Ge C2Y366P3T1D1: Body Parts

This stainless steel bullnose is the front trim piece that restores the look and fit of your range or oven control area. It provides finished protection for the control panel edge and improves appearance when the original trim is bent or damaged. What it does:

• Covers and protects the exposed edge of the control panel for a clean, finished appearance
• Replaces bent, dented, scratched or corroded front trim that affects aesthetics
• Helps keep debris and moisture out of the control-panel seam
• Restores proper alignment and fit of the control-panel face

• One stainless steel front bullnose trim

• Disconnect power to the appliance before starting any work
• Removal of the oven door or control panel may be required depending on model; basic hand tools typically needed
• Handle part carefully to avoid scratches; metal edges may be sharp

This anti-tip brace secures the range to the floor or wall to help prevent the appliance from tipping forward when a heavy load is on an open oven door or when pressure is applied to the top edge. It restores a key safety restraint and helps stabilize the appliance. What it does

• Anchors the range to reduce forward tipping when the oven door is open or heavy items are placed on the door
• Helps prevent accidents and appliance movement during normal use
• Works with the range's built-in leveling and mounting points to provide a secure attachment
• Commonly replaced after a move, installation, or if the original bracket is damaged or missing

• One anti-tip brace

• Follow the appliance installation manual for correct placement and mounting location
• Unplug the appliance (or shut off power) and remove access panels as needed before installing
• Use appropriate fasteners for your floor/wall material; secure to framing or floor as specified

This anti-tip bracket secures a freestanding range or oven to the floor or wall to help prevent tipping during normal use, improving safety and stability. Simple, durable bracket designed to restore the factory anchoring point. What it does:

• Anchors the rear/base of a freestanding range to help prevent the unit from tipping forward
• Reduces rocking or shifting when opening heavy oven doors or sliding cookware
• Restores the proper mounting point after damage or missing hardware
• Helps address symptoms like a range that tilts or moves when pressure is applied

• One anti-tip bracket

• Follow the appliance OEM installation instructions; bracket mounts to floor or wall framing—locate a stud or secure to recommended substrate
• Turn off and disconnect power (and gas if applicable) and remove access panels as required before beginning work
• Use proper fasteners for your floor/wall material; do not rely on adhesive or weak anchors

The Cooling Fan Sensor is an OEM replacement part for GE ovens and ranges. It is a critical component that monitors and regulates the operation of the cooling fan, ensuring proper ventilation and temperature control within the appliance.

Symptoms of a bad cooling fan sensor:

• Overheating issues, with the oven or range becoming excessively hot
• Failure of the cooling fan to turn on or operate correctly
• Error codes or warning lights related to temperature or ventilation problems
• Potential safety hazards due to inadequate cooling and heat buildup

Causes of a faulty cooling fan sensor can include exposure to high temperatures over time, electrical malfunctions, or physical damage to the sensor or its wiring.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore ovens and ranges.

This strain relief secures and protects the appliance power cord or wiring where it enters the cabinet, reducing stress and preventing chafing or accidental disconnection for safer, more reliable operation. What it does:

• Locks the power cord or wiring in place to prevent pull-out or separation from internal connections
• Protects wires from sharp edges and abrasion at the cabinet entry point
• Helps maintain a safe routing path to reduce electrical wear and intermittent power issues
• Suitable when the cord feels loose, shifts at the entry, or shows signs of wear near the entry point

• Disconnect power at the breaker or unplug the appliance before installing
• Access the cord entry point per your model's service instructions; remove panels only as needed
• Seat the cord into the strain relief and secure it in the cabinet opening, ensuring no pinched conductors

The Wall Oven Capacitor Motor is an OEM part for GE wall ovens. Located inside the oven cavity, this motor is responsible for turning the convection fan which circulates hot air for even baking and roasting. 

Symptoms of a bad capacitor motor include:

• Inability to select convection bake or roast features 
• Uneven cooking results 
• Lack of air circulation inside the oven
• Strange noises coming from the fan/motor area
• The convection fan not turning on 

Causes of failure can be wear over time, damage from debris inside the oven, or occasional voltage fluctuations which can degrade motor components.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This is a stainless-steel machine screw used to secure components in appliances. Its #8-18 thread and 3/8" length provide a reliable, corrosion-resistant fastening where a short machine screw is required. What it does:

• Fastens panels, brackets, or small assemblies with a #8-18 threaded hole
• Resists rust and corrosion in humid appliance compartments
• Provides a short, secure hold where space is limited
• Compatible with standard #2 Phillips or compatible driver bit for installation

• Power off and unplug the appliance before servicing
• Use the correct driver to avoid stripping the head
• Do not overtighten; stop when snug to avoid thread or component damage
• If replacing multiple fasteners, reuse only the same size and type

This is a replacement 8-18 x 5/16 machine screw used to secure appliance panels and components. It restores proper fastener fit so parts stay mounted and operate safely. What it does:

• Fastens panels, brackets, and small components where an 8-18 x 5/16 screw is specified
• Prevents loose parts, rattling, and misalignment caused by missing or worn screws
• Provides the correct thread size and length for reliable reattachment
• Works wherever the OEM calls for this specific 8-18 x 5/16 screw

• Turn off and unplug the appliance before starting any repair
• Use the correct screwdriver or driver bit to avoid stripping the head
• Do not overtighten; snug until secure to prevent damage to threads or mounting surfaces
• If replacing multiple fasteners, use matching screws to maintain proper fit and function

Replacement front frame bumper that cushions and supports the appliance's front frame or door trim, helping reduce vibration and prevent metal-on-metal contact—restoring a secure, quiet fit for the door or trim assembly. What it does:

• Cushions the front frame/door trim to prevent wear, chipping, and metal rubbing.
• Helps align and stabilize the door/frame for proper closing and fit.
• Reduces rattling and vibration noise during operation.
• Commonly replaced when the door feels loose, rubs against the cabinet, or makes noise.

• Disconnect power to the appliance before beginning any repair.
• May require removal of the door trim or front panel—use basic hand tools and keep fasteners organized.
• Seat the bumper fully in its mounting location; avoid forcing or deforming the part.