Parts for Ge JB755BJ8TS: Body Parts

Mounting bracket that secures the capacitor to your range frame. Replace if bent, broken, or missing to properly support and position the capacitor.

Rangetop enclosure for electric ranges. Installs on the main cooking surface to contain and support the heating elements. Replace if cracked or damaged.

Range not heating or burners not working? This terminal block connects power to your electric range elements. Common fix for heating failures on ovens and cooktops.

Replace your electric range's lower drawer assembly if bent, jammed, cracked, or missing. Restores smooth glide operation and proper alignment.

Replace a cracked, dented, or missing side panel on your electric range. This structural cover panel installs on the exterior side of your appliance.

This replacement drawer panel restores the finished front trim of the appliance's drawer for a clean, even appearance. It matches original fit and finish to replace a scratched, dented, or damaged drawer front and refresh the unit's look. What it does:

• Replaces a worn, dented, scratched, or otherwise damaged drawer front to restore proper appearance
• Provides the correct fit and mounting points so the drawer closes and lines up with surrounding cabinetry
• Maintains original exterior finish and edge trim for a consistent look
• Supports proper function of the drawer by replacing bent or distorted front surfaces

• Disconnect power to the appliance before beginning any repair that exposes electrical components
• Remove drawer and mounting hardware per factory instructions to access fasteners; keep track of clips and screws
• Align panel to drawer frame and secure with original fasteners; do not overtighten to avoid distortion

Rear insulation panel that installs behind the oven cavity to contain heat and protect surrounding components. Replace if cracked, damaged, or missing.

Replace a missing, bent, or corroded oven rack in your electric range. This rack slides on side rails to support bakeware and cookware at the correct level.

Aligns and stabilizes your range's lower storage or warming drawer for smooth sliding and flush closure. Replace if cracked, worn, or missing to restore fit.

Oven slow to heat or not heating at all? This hidden bake element delivers consistent bottom heat for proper baking. Moderate DIY, about 1 hour.

Broiler not working or burned out? This broil element radiates intense heat from above to sear and brown foods. Straightforward DIY replacement.

Fix F2 error codes and inaccurate oven temperatures by replacing a faulty temperature sensor. Simple 15-minute DIY repair with basic tools.

Halogen oven light assembly illuminates your electric range interior so you can monitor cooking without opening the door. Replace when dim or burned out.

Black front trim frame for electric range. Covers gaps and restores finished edge around door or control panel. Replaces cracked, scratched, or missing trim.

Secures your range to the floor or wall to prevent forward tipping. Replace if bracket is bent, broken, or missing during appliance relocation.

Range won't power on or has a loose power connection? This terminal block mount secures the electrical connection. Straightforward install in under an hour.

Secures your range door hinge to the cabinet frame for proper pivot and seal. Replace if door sags, won't close flush, or hinge is loose. Confirm fit with your model number.

Rear drawer support bracket mounts at the base of your range to provide weight-bearing support for the lower oven drawer. Replace if cracked or missing.

Reflector pan sits under the bake element in your electric range oven cavity. Replace if cracked, warped, or rusted to restore proper heat direction.

Convection fan won't run or oven bakes unevenly? This wall oven fan motor circulates hot air for even cooking. Moderate DIY repair, 1-2 hours.

This temperature sensor harness connects the refrigerator/freezer thermistor to the main control board, restoring reliable temperature sensing and control. It helps the appliance maintain consistent cooling by ensuring the temperature sensor communicates correctly. What it does:

• Carries the thermistor signal from the evaporator/well sensor to the control board
• Replaces frayed, damaged, or corroded wiring that can cause temperature errors
• Helps resolve symptoms like erratic temperatures, incorrect cooling cycles, or temperature error codes
• Maintains proper connector fit and routing to prevent intermittent sensor readings

• One temperature sensor harness

• Disconnect power before installing to avoid shock or short circuits
• Access may require removing interior panels or the control housing; keep fasteners organized
• Match connector orientation and route harness away from sharp edges and moving components

Replacement mounting screw for cooktops and ranges. Secures cooktop components to the frame. Replace if screw is stripped, missing, or damaged.