Parts for Ge ZGP366LN1SS: Body Parts

This wire bushing protects appliance wiring where wires pass through metal or plastic panels, helping prevent chafing and shorts. It restores a safe insulating barrier to wiring harnesses and terminals. What it does:

• Cushions and isolates wires where they pass through openings to prevent abrasion and wire damage
• Helps stop rubbing that can wear insulation and cause arcing or shorts
• Reduces risk of intermittent power, blown fuses, or burning smells from damaged wiring
• Restores proper routing and strain relief for affected harnesses

• Remove power to the appliance before accessing wiring; disconnect power at the breaker or unplug.
• Inspect surrounding wire insulation and harness for damage; replace any wires that show charring or exposed conductors.
• Push the bushing into the opening until seated, then route the wire through the bushing to ensure a snug fit.

Range display lights flickering or completely dark? This LED power supply module converts voltage to power your control panel lighting. Moderate DIY repair.

Secures the power supply assembly to your range or oven frame. Replace if bracket is bent, cracked, or missing to keep electrical connections stable.

Range not heating or igniting? This control relay board routes power to igniters and burners. Fixes intermittent operation and failed starts on gas ranges.

8-18 x 1/2 inch screw for gas range assembly. Replace when missing, stripped, or corroded during oven repairs or maintenance work.

Speed nut clip secures your range oven bottom panel. Replace when missing or damaged to prevent panel rattling. Verify fit with your model number.

Front frame gasket for gas ranges. Replace when worn, cracked, or causing heat loss around oven door. Verify compatibility with your model number.

Secures the toe kick panel to your range base. Replace if the toe kick is loose, rattling, or won't stay in place. Verify fit with your model number.

Leveling leg kit for ranges and wall ovens. Includes adjustable feet to stabilize and level your appliance. Replace cracked, bent, or missing legs.

Secures freestanding ranges to the floor or wall to prevent tipping. Replace if bracket is missing, bent, or damaged during appliance installation.

Secures your range to the floor or wall to prevent tipping when the oven door is open. Replace if bracket is bent, broken, or missing during installation.

Fix uneven oven temperatures or overheating electronics with this 45mm tangential blower motor. Restores directed airflow in your gas range cavity.

This small metal nipple secures or connects appliance components, restoring proper alignment and a stable mechanical or fluid connection. It's a simple replacement that helps appliances function reliably. What it does:

• Provides a secure mounting point or connection between parts
• Restores proper alignment for linked components
• Replaces worn or damaged fittings that can cause rattling or instability
• Helps maintain a leak-free or stable mechanical joint when used as intended

• Disconnect power and/or gas and follow all safety procedures before starting work
• Install in the original orientation; hand-start fasteners to avoid cross-threading, then tighten to secure
• If the nipple interfaces with a fluid or gas line, inspect seals and replace gaskets or O-rings as needed and check for leaks after reassembly

Controls gas flow to your range oven burner. Replace this regulator if it's cracked, corroded, or leaking to restore proper gas pressure control.

Convection fan won't run or oven bakes unevenly? This wall oven fan motor circulates hot air for even cooking. Moderate DIY repair, 1-2 hours.

Replacement power cord for gas ranges. Installs at the rear connection to supply mains electricity. Order when your original cord is frayed, cut, damaged, or worn.

Mounting screw hardware for ranges and cooktops. Replace missing, stripped, or corroded screws used to secure panels, brackets, or components.

Fixes gas range not igniting or burners not lighting. This safety valve controls gas flow to your burners. Moderate DIY repair, 1-2 hours install time.

Mounting bracket that secures the capacitor to your range frame. Replace if bent, broken, or missing to properly support and position the capacitor.

Replacement screw for refrigerators. Secures handles, panels, and internal components. Order if yours is missing, stripped, or lost during repairs.

Fix burners that won't light, gas odors, or sputtering flames with a new gas range safety valve assembly. Controls gas flow for safe operation.

Fix burners that won't ignite or turn off when your gas range control knobs aren't responding. This reed switch board detects knob positions.