Parts for HCR2250ADS: Body Parts

A replacement wire oven rack that restores stable, level support for cookware and bakeware. Designed to slide into existing oven rack supports for easy re-use and reliable cooking performance. What it does:

• Provides a sturdy, level surface to hold pans, baking sheets and cookware
• Replaces bent, warped or rusted racks that cause uneven cooking or tipping
• Restores smooth in-and-out sliding if the original rack was sticking or misaligned
• Helps prevent cookware from contacting oven walls or heating elements

• Allow the oven to fully cool before handling the old rack or installing the new one
• Install by aligning the rack with the oven's side supports and sliding it into place; no tools required for most models
• Inspect rack supports for damage before installation; replace any damaged support components separately
• Clean with non-abrasive cleaners; avoid harsh chemicals that can damage coatings

This guide rail nut secures the oven rack guide/rail to the range/oven body so racks slide smoothly and stay aligned. A small replacement that restores proper rack movement and prevents rail separation or loose, wobbly racks. What it does:

• Fastens the oven rack guide/rail to the oven chassis so racks track correctly
• Helps stop the rack from sagging, slipping off, or becoming misaligned
• Restores smooth in-and-out rack movement when the original nut is stripped or damaged
• Works with the existing guide/rail and mounting hardware to secure the assembly

• One guide rail nut (quantity: 1)

• Disconnect power to the appliance before starting any repair
• Remove oven racks and any door panels needed for access per OEM instructions
• Replacement typically requires removing a retaining screw/clip and swapping the nut; keep existing screws and clips unless otherwise specified

This adjustable leveling leg replaces a worn or damaged foot to stabilize and level your appliance, improving door alignment and preventing rocking. It restores safe, even contact with the floor for better performance and fit. What it does:

• Provides a height-adjustable support foot to level the appliance on uneven floors
• Helps stop rocking, vibration, and uneven door gaps caused by a collapsed or missing leg
• Transfers appliance weight to the floor so controls and doors operate correctly
• Works with appliances that use a threaded, screw-in leveling foot design

• Disconnect power (and gas if applicable) and unplug the appliance before service
• Tilt or raise the appliance only as recommended by the manufacturer; use a second person or support to prevent tipping
• Turn the leg by hand or with a wrench to raise or lower; adjust until appliance sits level and stable
• Do not overtighten or force parts; if the mounting bracket or threads are damaged, replace bracket and/or

This replacement oven door gasket seals the oven cavity to help maintain consistent cooking temperatures and keep heat inside the oven for efficient operation. It restores a tight seal on worn, cracked, or deformed door seals. What it does:

• Creates a heat-tight barrier between the oven door and cavity to help maintain oven temperature
• Helps prevent heat and steam from escaping during cooking or self-clean cycles
• Reduces energy loss and improves cooking performance when the original seal is no longer effective
• Commonly replaced when the gasket is torn, compressed, brittle, or missing sections

• One oven door gasket

• Inspect the door and channel for debris before installing; clean surfaces for best fit
• Most gaskets press or tuck into a continuous channel around the door — follow the oven manufacturer's alignment method
• Wear gloves to avoid cuts from sharp edges and allow the oven to cool completely before starting

This anti-tip bracket assembly secures the rear of your range to the floor or wall. It helps prevent the appliance from tipping forward during everyday use and supports compliance with manufacturer safety and installation requirements. What it does:

• Anchors the range so the rear leveling foot engages the bracket to help prevent tipping
• Helps correct a range that rocks, shifts, or tilts when the door is opened or racks are pulled
• Replaces a missing, bent, or corroded anti-tip bracket
• Supports passing the required anti-tip safety check after installation

• One anti-tip bracket assembly

• Disconnect power; for gas models, also shut off the gas supply before starting
• Mount the bracket to the floor or wall as directed in the range's installation instructions
• Slide the range back so the rear leveling foot fully engages the bracket; verify the unit is level
• Perform the anti-tip test specified in the installation manual to confirm proper engagement