Parts for Hot Point RGA720EK7WH: Body Parts

Replacement power cord for gas ranges. Connects your unit to the wall outlet. Replace if cord is worn, cut, heat-damaged, or causing burning smells.

Panel mounting screw secures trim, bezels, and internal components on ranges and cooktops. Replace when stripped, corroded, or missing to restore fit.

This replacement screw secures trim and appliance panels with a compact 3/8" length and #8-18 thread, providing a simple fastener solution for loose or missing hardware. Fits a variety of appliance assemblies where short machine screws are used. What it does

• Fastens panels, trims, brackets, and small components that use #8-18 threaded holes
• Restores secure attachment for loose or rattling parts
• Replaces stripped or missing short screws to prevent gaps or movement
• Small size is suited for shallow mounting areas and sheet-metal attachments

• One screw

• Use the correct driver or bit to avoid stripping the head; a magnetic screwdriver helps with small fasteners
• Tighten until snug—do not overtighten to prevent thread damage or panel deformation
• Disconnect power to the appliance before working on internal components or near electrical connections
• Match those details for best fit and performance

Replacement screw for electric and gas ranges. Secures internal components and panels. Needed when original hardware is stripped, missing, or lost during repairs.

Secures your range power cord at cabinet entry to prevent wire damage and disconnection. Replace if cord is loose or clamp is cracked. Confirm fit with your model number.

This metal backguard panel restores the rear cover and mounting surface on your range, protecting wiring and supporting control components. It returns the unit to a finished appearance and maintains safe clearance at the rear. What it does:

• Covers and protects the range's rear wiring, terminals and internal components from spills and debris
• Provides a mounting surface for switches, receptacles or control housings as designed
• Helps maintain proper appliance ventilation and a finished exterior look
• Commonly replaced if bent, rusted, cracked or missing after service or impact

• Disconnect power (and gas supply if applicable) before servicing the appliance
• Remove cooktop or rear access panels as required to access mounting fasteners
• Support the panel during removal/installation to avoid scratching surrounding surfaces
• Use only manufacturer-specified fasteners and ensure wiring/ground connections are secure after reassembly

This oven floor deflector assembly restores proper airflow and heat protection in the lower oven cavity so food cooks evenly and internal components stay shielded from direct heat. It's a direct replacement for a damaged or warped deflector. What it does:

• Redirects and evens oven heat across the lower cavity to improve baking and roasting consistency.
• Shields internal insulation and components from hot bake/broil flames and debris.
• Replaces warped, dented, or missing deflector that can cause uneven cooking or rattling.
• Helps prevent direct flame contact with oven floor and lowers risk of food drippings burning on surfaces.

• One bottom oven and deflector assembly

• Disconnect power to the appliance and allow the oven to cool completely before starting.
• Basic hand tools are typically required; follow the appliance service manual for panel removal steps.
• Handle edges carefully—metal parts may be sharp.

8-18 x 1/2 inch screw for gas range assembly. Replace when missing, stripped, or corroded during oven repairs or maintenance work.

Replace your range's anti-tip bracket to secure your appliance safely to the wall. Essential safety component that prevents tipping when installed.

Base support kit for gas ranges. Installs at the bottom of the range to provide structural stability. Replace if cracked, broken, or missing.

This replacement leveling screw secures and adjusts an appliance's leg so the unit sits level and stable on the floor. Restores proper tilt for even door operation and stable performance. What it does:

• Replaces a worn or damaged leveling screw used to raise or lower an appliance leg
• Helps stop rocking, reduce vibration, and keep doors aligned
• Common fix when an appliance tilts forward/back or is uneven on the floor
• Works with the corresponding leveling leg/assembly to set final height

• Support the appliance before adjusting or removing leveling hardware to prevent tipping
• Use appropriate hand tools; tighten securely but avoid over-torquing
• No electrical disconnection is typically required, but unplug if working near electrical components
• If the leveling leg assembly is damaged, replace the entire leg/assembly per manufacturer instructions

Wire clip secures electrical connections to heating elements in ranges. Replace if worn, cracked, or loose to restore proper contact. Verify fit with model.

Screw for electric and gas ranges. Secures internal components and panels. Replace if lost, stripped, or corroded to properly fasten range parts.

Insulation that wraps around the safety valve on gas ranges. Replace if torn, deteriorated, or missing to maintain proper heat protection.