Parts for Thermador MED272ES01: Bottom Oven Parts

This sealing plug closes an unused port or opening to prevent leaks and keep internal components protected. It restores a watertight seal and helps prevent debris or moisture from entering appliance cavities. What it does:

• Seals an open port or service access to stop water leaks and moisture intrusion
• Helps keep debris and contaminants out of pumps, valves or internal cavities
• Restores proper sealing after maintenance or component replacement
• Can reduce risk of water damage or corrosion when installed correctly

• Disconnect power and water supply before accessing the part
• Inspect any O-rings or sealing surfaces; replace damaged seals
• Hand-tighten or press into place per manufacturer guidance; avoid over-tightening

The Bake Element is an OEM part for Bosch ranges. This bake element replaces the standard heating coil located at the bottom of the oven cavity and provides reliable, even heating for baking, roasting and more.

Causes of a bad bake element can include normal wear and tear over time, becoming clogged with burnt-on residue, or failure of internal wires or heating coils.

Symptoms of a bad bake element include:

• Fluctuating oven temperatures
• Uneven or inefficient cooking/baking
• The oven not heating at all or only heating to a low temperature

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This replacement door seal is the appliance gasket that restores a tight, reliable seal where the door meets the cabinet. Replacing a worn or damaged seal helps stop leaks, reduce energy loss, and improve performance. What it does:

• Creates a weather-tight barrier at the door to prevent water or air from escaping
• Helps maintain proper internal temperature and energy efficiency
• Reduces drafts, moisture build-up, and related odors
• Restores normal operation when a torn, compressed, or hardened gasket causes leaks

• One door seal/gasket

• Disconnect power to the appliance before starting any work
• Remove the old gasket carefully; some models use clips, channels, or adhesive—retain fasteners as needed
• Seat the new seal evenly into the channel and compress gently to form a continuous seal
• After installation, run a brief test (no operation if unsafe) and inspect for uniform contact around the door

This service access cover protects internal components and wiring while keeping the appliance's exterior neat. It restores a clean appearance and helps prevent accidental contact with internal parts during normal use. What it does:

• Protects internal components, connectors and wiring from dust and debris
• Helps reduce risk of accidental contact with electrical parts
• Restores the appliance's finished look after repairs or maintenance
• Useful when replacing or servicing nearby components that require the cover removed

• Disconnect power (unplug or switch off circuit breaker) before starting any work
• Remove and reinstall using the factory mounting clips or screws; avoid forcing the cover to prevent breakage
• Handle plastic tabs gently—inspect tabs and mounting points for damage before final install

The Sensor is an OEM replacement part for Bosch ranges. It monitors conditions inside the oven compartment such as temperature and diagnosing faults. 

Symptoms of a bad sensor include:

• The oven not heating or cooking unevenly
• Inaccurate temperature readings displayed  
• Erratic or unpredictable ignition/operation  
• Error codes appearing related to sensor faults

Causes of failure can be normal wear over time from high heat exposure, accidental damage compromising sensor integrity, or intrusion of liquids or debris confusing readings.

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore ranges.

Heater-Bottom replaces the dishwasher's lower heating element, restoring water heating and improving wash and drying performance. It heats wash water for effective cleaning and helps reduce moisture left in the tub after a cycle. What it does:

• Warms wash and rinse water so detergent dissolves and soils are removed more effectively — symptom: poor cleaning performance.
• Raises final rinse temperature to aid drying — symptom: dishes stay wet after cycle.
• Replaces a failed or open bottom heating element — symptom: no heat or heater-related error/alerts.
• Restores normal cycle operation when temperature-dependent functions are affected.

• Disconnect power to the appliance before beginning any repair to avoid electric shock.
• Route wires exactly as the original; ensure all connector terminals are fully seated.
• Inspect wiring and insulation for damage and replace any compromised components to prevent shorts.
• Test the element for continuity with a multimeter before and after installation to ensure proper operation.

This support mounting bracket secures internal components to the appliance frame, restoring proper alignment and stable operation. It replaces a worn, broken, or loose support to help reduce rattling and prevent component sag. What it does:

• Provides a secure mounting point for internal parts and assemblies
• Re-establishes correct alignment when a bracket is bent or broken
• Helps reduce vibration and rattling caused by loose or damaged supports
• Commonly replaced when a component shifts, rubs, or no longer sits flush

• Disconnect power and water before starting any repair.
• Basic hand tools are typically required; follow OEM service instructions for disassembly/reassembly.
• Inspect adjacent fasteners and clips; replace any that are damaged to ensure a secure fit.