Parts for Ge GTUP240EM6WW: Cabinet (2) Parts

Size: 8 - 18 ab.

A push-on speed nut that secures panels, trim, or lightweight components to studs and shafts, restoring a tight, rattle-free fit. Ideal when the original retaining nut is damaged or missing. What it does

• Climbs and locks onto a threaded stud or shaft to hold panels and assemblies in place
• Prevents loosening and vibration that can cause rattles or misalignment
• Common replacement when the original nut is stripped, cracked, or no longer grips

• Disconnect power and water (if applicable) before servicing the appliance
• Press the nut firmly onto the stud or shaft until fully seated; use pliers for tight fits if needed
• Replace any damaged mating hardware for a secure repair

This is a #8-18 by 5/8-inch Torq II-head screw used to secure appliance panels and components. It provides a reliable fastener option when replacing stripped or missing screws to restore proper fit and reduce vibration or rattling. What it does:

• Secures trim, panels, brackets or small components to appliance frames
• Restores proper alignment and reduces noise from loose parts
• Replaces worn, stripped, or missing fasteners to prevent further damage
• Compatible where an 8-18 thread and 5/8" length with a Torq II-style head are specified

• One screw

• Use the correct Torq II driver bit to avoid cam-out or head damage
• Tighten until snug; avoid over-tightening which can strip threads or crack plastic
• If replacing rusted or stripped screws, inspect mating threads and replace as needed
• Disconnect power and follow appliance safety instructions before servicing

This is a replacement 8-32 trilobular hex screw used to fasten appliance panels and components. It restores secure mounting and helps eliminate loose parts or rattling caused by missing or worn fasteners. What it does:

• Secures panels, brackets, or components in place using an 8-32 trilobular thread form
• Helps prevent vibration, rattling, and loose connections when fasteners are missing or stripped
• Designed to match OEM thread style for proper engagement and retention
• Used wherever a small hex-head machine screw is required for assembly

• Use the correct driver/socket to avoid rounding the hex head
• Tighten to snug fit; avoid over-torquing which can strip threads or damage parts
• If replacing a stripped hole, inspect mating threads and consider a thread repair or alternate fastening method
• Disconnect power to the appliance before accessing internal components to reduce risk of shock or injury

This electronic control board assembly is the washer's central controller, managing cycle selection, timing, and communication with key components. Replacing a failed board can restore proper operation and dependable cycle performance. What it does

• Interprets user inputs and sensor signals to run wash, rinse, and spin sequences
• Sends power and control signals to the motor, drain pump, water valves, and lid/lock as designed
• Controls cycle timing, speeds, and status indicators
• Symptoms may include: washer won't power on or start, unresponsive controls, cycle won't advance or stops mid-cycle, or error codes/blinking lights

• One electronic control board assembly

• Disconnect power before servicing; verify no voltage is present
• Handle the PCB by the edges and use ESD protection
• Photograph/label wiring; transfer connectors to the new board one at a time
• Secure the board in the original mounts; some models may require configuration per service instructions

This enclosure board is the molded housing that secures and protects the refrigerator's control electronics and user interface components. It helps keep wiring and circuit boards organized and shielded from moisture and debris for reliable operation. What it does:

• Holds and protects control boards, connectors, and wiring inside the control cavity
• Keeps moisture and dust away from sensitive electronics to reduce failure risk
• Provides mounting points and alignment for switches, displays, and harnesses
• Restores proper fit and clearance for the appliance's control assembly

• Recommended for technicians or experienced DIYers comfortable working with appliance electronics
• Disconnect power to the appliance before servicing to avoid shock or damage
• Handle PCB-mounted connectors and wiring carefully; avoid sharp bends or pinching the harness
• Secure all fasteners to prevent vibration issues