Parts for Kitchenaid KUID508HPS01: Cabinet, Door And Liner Parts

Size: 8-18 x 1 1/4 inch.

This replacement door bin restores inside-door storage on your refrigerator so bottles, condiments and small items stay organized and secure. Durable molded plastic matches the original fit and function. What it does:

• Provides a removable shelf inside the refrigerator door to hold bottles, jars and small containers
• Replaces cracked, broken or missing door storage that no longer secures items
• Restores original storage capacity and prevents items from falling when opening the door
• Fits into existing mounting ledges or rails and snaps into place for everyday use

• Empty contents from the damaged bin before removal
• Most installations are tool-free—lift out the old bin and snap the new one into the door ledges
• Inspect door ledges for damage before installing; replace any broken mounting clips if needed
• Handle carefully to avoid sharp edges on broken plastic and follow safety precautions

This spacer positions and supports appliance components to maintain correct clearance and alignment, helping parts fit securely and reducing wear. Replace damaged or missing spacers to restore proper component spacing and quiet operation. What it does:

• Keeps panels, brackets or assemblies properly spaced to prevent rubbing and misalignment
• Helps maintain correct clearance for moving parts and seals
• Reduces vibration and noise caused by loose or shifted components
• Restores fit when a broken or worn spacer allows parts to sit unevenly

• Disconnect power before servicing; follow all safety instructions in your owner's manual
• Confirm correct orientation and placement before tightening fasteners
• Inspect surrounding parts (brackets, fasteners, mounting points) and replace if damaged

Size: 8-18 x 1/2 inch.

This exterior door panel restores the dishwasher's front appearance and protects the inner door assembly from everyday wear. A factory-style replacement that matches original color and finish for a clean, finished look. What it does:

• Replaces a scratched, dented, or faded outer door surface to improve appearance.
• Covers and protects inner door components and trim from moisture and damage.
• Helps ensure the control panel and handle area have a proper mounting surface and alignment.
• Matches original color/finish so the appliance looks consistent with the rest of the cabinet.

• One exterior door panel

• Install requires removing the door trim and possibly the inner door liner; follow for panel removal and reassembly.
• Handle and control trim may need to be transferred; only the outer panel is listed as supplied.
• Use caution supporting the door during disassembly to avoid dropping or damaging the door or hinges.
• Disconnect power and water to the appliance and follow all safety procedures before beginning repair.

A small metal clamp that secures flexible hoses or tubing in laundry and kitchen appliances to prevent leaks and keep connections tight. Simple, durable replacement for a worn or loose hose fastening point. What it does

• Holds a hose or tube firmly to a barb, fitting or nipple to stop leaks and movement
• Restores a secure connection where a cracked or corroded clamp allows fluid or air escape
• Common service item for loose drain, fill, or vent hoses showing seepage or slipping
• Helps maintain proper appliance function by ensuring sealed hose connections

• One clamp

• Disconnect power and water before servicing; follow your appliance safety procedures
• Inspect mating hose and fitting for damage; replace hose if cut or brittle
• Use the correct pliers or clamp tool for safe installation and to avoid over-tightening

This 18" door gasket seals the appliance door to help maintain proper temperature and efficiency. It replaces a worn or damaged seal so the appliance can run normally and reduce energy loss. What it does:

• Creates a tight seal around the door to help prevent air leaks and temperature drift
• Helps reduce frost or moisture buildup caused by a failing gasket
• Can stop excessive cycling or longer run-times tied to seal failure
• Restores proper door closure for consistent performance

• Disconnect power to the appliance before starting any repair
• Remove the old gasket carefully; some adhesive or retainer clips may be present
• Inspect the door and retainer for damage or debris before installing the new gasket

This retainer clip secures the appliance axle in place to keep rotating parts aligned and running smoothly. Replacing a worn or broken clip helps reduce noise, vibration and drivetrain misalignment for reliable operation. What it does:

• Holds the axle/shaft in position to prevent lateral movement and maintain alignment
• Prevents excessive play that can cause noise, vibration or uneven wear
• Helps keep connected components (drum/rotor/wheel) tracking correctly
• Commonly replaced when clipped, bent or missing after repair or wear

• Disconnect power before starting any repair
• Removal may require pliers or a small punch to release the old clip; reinstall by snapping into the axle groove
• Inspect mating shaft and housing for wear or damage before installing the new clip

This name plate is the appliance's model and serial identification label—an easy way to restore clear product ID for service, parts ordering, and warranty records. Keeps your appliance information visible and readable. What it does:

• Displays manufacturer model and serial numbers and other factory ID details
• Restores a missing or damaged ID label so technicians can identify the correct parts and specs
• Helps when registering the appliance or filing warranty and service requests
• Prevents delays caused by unreadable or absent identification information

• Clean and dry the mounting surface before applying; remove old adhesive residue
• Align carefully and press firmly; some name plates use adhesive backing or mounting tabs
• Do not cover vents, controls, or safety labels when installing

Size: 8-18 x 5/8 inch.

This hinge spring is the OEM replacement tension spring that helps support and balance the oven/range door for smooth opening, controlled closing, and proper door positioning. Restores stable door movement and reduces sudden drops. What it does:

• Provides tension to the door hinge so the door opens and closes smoothly
• Helps keep the door in the intended open or partially open position
• Reduces door sag, slipping, or sudden closing
• Can stop noisy or uneven hinge movement caused by a worn spring

• Disconnect power to the appliance before starting any repair.
• Use gloves and eye protection; springs are under tension and can snap back.
• Follow the manufacturer's removal/installation steps — you may need to partially or fully remove the door to access the hinge spring.

Size: 8 x 1-1/4 inch.

This screw grommet anchors a screw in thin appliance panels so trim, covers, or consoles stay tight. It provides a snug, vibration-damping fit where a standard screw could loosen or strip over time.

• Creates a captive insert so a screw can securely fasten to sheet metal or plastic panels
• Replaces a worn, cracked, or missing grommet to restore proper screw retention
• Helps reduce panel rattles and movement from vibration
• Typical signs of failure: screw won't tighten, panel or trim feels loose, grommet falls out

• Disconnect power and shut off gas/water as applicable before servicing
• Remove the screw and lift out the old grommet; clear debris from the opening
• Press the new grommet straight into the hole until fully seated and flush
• Reinstall the screw and tighten gently to avoid deforming the grommet

This front grille is the exterior trim piece that covers and protects the lower front of an 18-inch built-in ice maker, restoring appearance and allowing proper airflow. It replaces a cracked, faded, or damaged grille to keep the unit looking finished. What it does:

• Covers the ice maker's lower front opening and provides a finished appearance
• Protects internal components from debris while allowing ventilation
• Helps prevent drafts and keeps the trim line sealed and tidy
• Common symptom: grille is cracked, broken, loose, or discolored

• Designed for drop-in or snap-fit replacement at the front of the ice maker;
• Remove power to the appliance and empty nearby ice/water before beginning service
• Use basic hand tools; avoid excessive force to prevent breaking surrounding trim

This genuine fastener secures panels and components on compatible appliances so panels and parts stay safely in place during use. Small and simple, it restores proper fit where a missing or damaged screw causes loose or rattling parts. What it does:

• Fastens panels, brackets, or small components to restore secure attachment
• Helps eliminate loose panels, rattling, or misaligned parts caused by missing hardware
• Used wherever the OEM screw is specified for a clean, factory-fit repair
• Matches the original thread and head style for proper engagement

• Always disconnect power and water before starting appliance repairs
• Use the correct screwdriver or driver bit to avoid stripping the head
• Hand-start threads, then tighten snugly — do not overtighten to avoid damaging parts
• Keep small parts away from children and pets during repair

This adjustable leveling leg threads into the appliance base to set height and stabilize the cabinet. Replacing a worn or missing leg helps stop rocking and vibration and helps maintain proper alignment for reliable operation.

• Provides adjustable support at one corner of the appliance
• Helps level the unit for correct alignment with floor or cabinetry
• Reduces rocking, vibration, and rattling noises
• Replaces stripped, bent, cracked, or missing leg

• Disconnect power and, if applicable, shut off water before servicing
• Carefully support or brace the appliance to access the base safely
• Start the new leg by hand to avoid cross-threading; adjust height gradually
• Use a level to check side-to-side and front-to-back, then recheck after positioning

This refrigerator door handle provides a reliable grip for opening and closing the fridge door and restores a finished look after the original handle is cracked, loose, or damaged. It's a direct-fit replacement designed for easy swap-out. What it does:

• Restores secure, comfortable grip for normal door operation
• Replaces cracked, broken, loose, or cosmetically damaged handles
• Helps prevent door damage from continued use of a compromised handle
• Matches original mounting points for proper alignment and function

• Turn off power to the appliance or unplug before starting any service that may expose wiring or lights
• Use basic hand tools; save original screws and hardware when possible
• Support the door while removing/installing the handle to avoid stress on hinges

This edge guard grommet cushions and protects a cabinet or appliance panel edge to prevent wear and reduce chafing. It restores a finished look and helps keep adjacent parts from rubbing or vibrating. What it does:

• Provides a protective barrier along a sharp or exposed edge to prevent damage and wear
• Cushions panels and trim to reduce noise from vibration or movement
• Helps maintain a finished appearance where panels meet or overlap
• Can prevent metal-on-metal or metal-on-plastic contact that leads to abrasion

• One edge guard grommet

• Inspect the mounting area for damage or debris and clean before installing
• Press or slide the grommet into place along the edge until fully seated; trim excess if applicable
• If adhesives or clips are used, follow OEM recommendations for secure attachment
• Disconnect power and follow all safety precautions when working near electrical components

This lower panel wrap replaces the stainless steel trim that covers the bottom front of your range/oven, restoring the appliance's finished look and protecting internal components from dirt and spills. Ideal for cosmetic repairs and panel damage. What it does:

• Replaces a dented, scratched or discolored lower front wrap to restore appearance
• Covers and protects internal components behind the kick area from debris and spills
• Helps maintain a finished trim line under the oven door
• Can reduce visible gaps or misaligned trim after impact or wear

• Disconnect power to the appliance before beginning any work
• May require removal of the oven door, kick plate or mounting screws for access
• Handle edges carefully—metal trim can have sharp edges