Parts for Whirlpool GI15NDXZS0: 02 - Cabinet, Door And Liner Parts

Reduces chlorine, contaminants, and odors from your refrigerator's water and ice. Replace every 6 months for optimal performance. Confirm fit by model.

Replace missing or stripped mounting screws in your refrigerator or ice maker. 8-18 x 1 1/4 inch screw secures panels and components inside the unit.

Replacement mounting spacer for ice makers. Maintains proper clearance and alignment between components. Replace if cracked, broken, or missing.

8-18 x 1/2 inch mounting screw for refrigerators, washers, dryers, and other appliances. Replace stripped, missing, or damaged screws during repairs.

Replacement door for ice maker units. Installs on the front of the ice maker to provide access and seal the compartment. Order if original is cracked or broken.

Replacement door cam for freestanding ice makers. This plastic cam component controls door operation. Order a new one if your original is cracked or broken.

Ice maker door won't stay closed or seal properly? This door catch assembly restores secure latching to maintain proper temperatures and operation.

Bottom door gasket for ice makers. Seals lower door edge to maintain temperature and prevent frost buildup. Replace if worn, cracked, or leaking air.

Ice not freezing properly or melting too fast? A worn door gasket lets warm air in. This 15-inch seal restores proper insulation in about 20 minutes.

Door stop for freestanding ice makers. Prevents door from overextending and controls opening angle. Replace if broken, cracked, or missing.

Door stop for freestanding ice makers. Prevents door from overextending and controls opening range. Replace if broken, cracked, or missing to secure door.

Ice maker door won't close properly or alignment is off? This top hinge restores secure mounting and smooth operation. Simple DIY fix in under 30 minutes.

Replacement cover assembly for ice makers. Installs to replace cracked, broken, or missing covers. Protects internal components and restores appearance.

Replacement mounting screw for ice makers. Secures internal components and panels. Order a new screw if yours is stripped, missing, or damaged.

Filler end cap for 15-inch ice makers. Replaces cracked, broken, or missing black end cap trim pieces. Installs at cabinet edge for finished look.

Water pooling under your ice maker? A cracked or damaged drain tube causes leaks and floor damage. This 15-inch tube restores proper drainage flow.

Missing or damaged ice scoop? This replacement scoop fits most ice makers and provides sanitary ice retrieval. Measures 4" x 10.5" for easy handling.

White door handle for ice maker access doors. Replaces worn, cracked, or broken handles to restore smooth opening and secure grip on your unit.

Black handle for ice maker compartment door. Installs on front panel to provide grip for opening and closing. Replace if cracked, broken, or missing.

Secures flexible tubing to fittings on water and drain lines. Replace when clamps lose tension or you find leaks. Confirm fit with your model number.

This replacement screw secures panels and components on compatible Whirlpool appliances, restoring proper fit and reducing rattles or loose trim. It's sized for appliance sheet-metal and trim fastening and matches the OEM finish for visible areas. What it does:

• Fastens panels, brackets, trims and small components to prevent movement and vibration
• Helps restore proper alignment and reduces rattling or gaps caused by missing or damaged fasteners
• Fits standard 8-18 threads with a 1.00 in. shank for common appliance mounting points
• Matches white finish for a discreet appearance on exposed areas

• Disconnect power and remove any access panels before working on the appliance
• Use the proper driver (Phillips or specified head) and start threads by hand to avoid cross-threading
• Tighten firmly but avoid over-torquing to prevent stripping or damaging sheet-metal
• Replace all like fasteners for even fit and alignment

Replacement screw for securing refrigerator panels, brackets, and trim pieces. Needed when original fasteners are missing, stripped, or damaged.

Bottom door hinge for ice makers. Secures lower door section for smooth opening and reliable alignment. Replace if door sags or won't close properly.

Secures your ice maker door to the hinge assembly for smooth pivoting. Replace if worn, damaged, or causing door misalignment, rubbing, or sagging.

8-32 x 1/2 inch mounting screw for refrigerators. Secures panels, brackets, and components. Replace lost, stripped, or corroded screws.

Grey nameplate for refrigerators. Attaches to the exterior panel to display model information. Replace if faded, damaged, or missing from your unit.

Grey nameplate for refrigerators. Attaches to the exterior panel to display model information. Replace if faded, damaged, or missing from your unit.

Size: 8-18 x 3/4 inch.

10-32 x 1/2 inch pan head machine screw secures panels, brackets, and internal components in ice makers. Replaces missing or damaged screws.

Secures panels, brackets, and trim in dryers, washers, and ice makers. Replace worn, stripped, or missing screws to restore proper fit and alignment.

Replacement scoop holder that mounts on the ice maker door to keep your ice scoop secure and accessible. Replaces broken or missing holders.

Adjustable leveling leg threads into dishwasher base to set height and stabilize cabinet. Replace worn, missing, or stripped legs to stop rocking.

Black front grill panel for ice makers. Covers the front exterior of your unit. Replace if cracked, discolored, or damaged to restore appearance.

White front grill panel for freestanding ice makers. Replace this cosmetic part if your original grill is cracked, discolored, or missing.

This group top panel is the cooktop surface that covers and supports burners and controls, restoring a clean, protected cooking area and preventing heat or spills from reaching internal components. It's a direct replacement for the 15" group-top assembly. What it does:

• Replaces a bent, rusted, cracked or damaged cooktop surface so burners and controls mount securely
• Shields internal wiring and components from spills, grease and heat
• Provides a flat, stable surface for burner grates and cookware
• Helps restore proper alignment of burner components and control openings

• Disconnect power to the appliance before beginning any repair; follow all safety precautions
• Moderate hand tools typically required; retain fasteners and any trim for reuse
• Inspect adjacent parts (burner bowls, burner heads, mounting brackets) for wear during replacement