Parts for Frigidaire FGHC2334KE1: 07 - Cabinet Parts

The Water Filter is an OEM replacement part for Frigidaire refrigerators. This PureSource Ultra Ultrawf Refrigerator Water Filter is designed to provide superior filtration, ensuring that your water and ice are clean and refreshing.

With the Frigidaire Refrigerator Water Filter, you can enjoy up to six months of crystal-clear water and ice. For the filter bypass, order part number 242294402. Get the most out of your Frigidaire appliance with a new OEM water filter, and enjoy clean, refreshing water and ice every time!

Causes of a bad part:

• Overused or expired
• Clogged by excessive impurities

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This evaporator coil cover protects the refrigerator's evaporator assembly and helps direct airflow for more consistent cooling. It replaces a damaged or missing interior cover to keep the coil shielded and the compartment operating as intended. What it does:

• Shields the evaporator coil from contact and debris to prevent accidental damage
• Helps direct cold air across the evaporator for more even cooling performance
• Reduces unwanted airflow patterns that can cause frost buildup or uneven temperatures
• Covers sharp edges on the evaporator assembly for safer access during service

• One evaporator coil cover

• Disconnect power to the appliance before beginning any repair
• Remove interior panels and shelves as needed to access the evaporator area
• Handle the evaporator and cover carefully to avoid bending fins or damaging nearby components
• Fully defrost the evaporator before installing the new cover

This plug covers the small factory test opening on an appliance cabinet or liner. Replacing a missing or damaged plug helps close the opening to maintain a better seal and restore a clean, finished appearance.

• Seals the factory test opening in the cabinet/panel
• Helps limit air and moisture infiltration through the hole
• Reduces condensation or frost forming around the opening
• Restores a finished look when the original cap is missing or damaged

• Disconnect power before servicing the appliance
• Clean and dry the opening area for proper fit
• Align and press the plug in by hand until it sits flush—do not force or enlarge the hole
• Avoid sharp tools or sealants that could damage the liner or insulation

The Door Light Switch is an OEM part for Frigidaire refrigerators. It is a component located inside the refrigerator door that turns the interior light on and off based on door position. The light switch works with a door switch plate and light socket assembly to automatically illuminate the interior when the door is opened.

Causes of a bad switch can be normal wear and tear over time, especially from frequent door openings. The contact points within the switch can become corroded or damaged.

Symptoms of a bad light switch include:

• Interior light not turning on at all when door is opened
• Light remaining constantly on even when door is closed
• Inconsistent or intermittent lighting

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
 

This genuine replacement screw secures appliance components and panels so parts stay properly aligned and rattle-free. Use it to replace a missing, stripped, or corroded fastener and restore a snug, reliable fit.

• Fastens brackets, covers, panels, and other hardware in their original locations
• Helps resolve loose or vibrating components and rattling noises
• Replaces missing or damaged hardware that can cause gaps or misalignment
• May be used in multiple locations

• Disconnect power; shut off water supply if working near water lines
• Compare to the original screw and install in the same location/orientation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Refer to your model's exploded view to verify quantity and placement

The Screw is an OEM replacement part for Frigidaire refrigerators. This small but essential component is used to secure various parts of the appliance, such as panels, brackets, or internal fixtures, ensuring the refrigerator's structural integrity and proper operation.

Over time, screws may become loose, stripped, or corroded due to regular use, environmental factors, or maintenance work. A damaged or missing screw can lead to misaligned parts or reduced stability of the appliance.

Symptoms of a bad or missing screw include:

• Loose or wobbly components within the refrigerator
• Panels or fixtures coming apart or misaligned
• Difficulty securing parts during maintenance or repair
• Rattling or unusual noises during operation

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Upper Door Closer is an OEM part for Frigidaire refrigerators. It helps ensure that the refrigerator door closes smoothly and seals tightly, preventing cold air from escaping and maintaining optimal cooling efficiency.

Causes of a bad door closer can include regular wear and tear from frequent use, accidental impact, or misalignment. A faulty door closer can lead to energy loss and inefficient cooling.

Symptoms of a bad upper door closer include:

• The refrigerator door not closing properly
• Gaps or poor sealing around the door
• Increased energy consumption due to escaping cold air
• Unusual noises when opening or closing the door

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This turntable roller assembly sits under the glass tray to support and guide it as it rotates. Replacing a worn or damaged ring helps restore smooth tray movement for more even heating and dependable microwave performance.

• Supports the glass tray and allows smooth, consistent rotation
• Helps prevent tray wobble, binding, or scraping noises
• Can address issues like the tray not turning or uneven cooking
• Replaces cracked, warped, or missing roller rings

• Disconnect power before servicing
• Remove the glass tray, lift out the old ring, and clean the cavity floor
• Place the new ring wheels-down, seat the tray on the coupler, and test rotation
• Do not operate the microwave without the roller ring and tray properly installed

This lower hinge secures and pivots a refrigerator door, restoring proper alignment and smooth opening. It helps stop door sag, uneven sealing, and rubbing that can cause cold loss or noisy operation. What it does:

• Provides a durable pivot point for the refrigerator door to open and close smoothly
• Restores correct door alignment to improve the door seal and cooling performance
• Stops door sag, rubbing against the cabinet, and uneven gaps that can lead to air leaks
• Helps reduce noise from a misaligned or worn hinge

• Support or remove the door before replacing the hinge to avoid injury or damage
• Keep fasteners and any hinge shims or bushings; reuse only if in good condition or replace with OEM parts
• Tighten mounting screws securely and check door alignment; minor shimming may be required

Lower hinge secures the bottom corner of a refrigerator door and provides a durable pivot for smooth opening and closing. Replacing a worn hinge restores proper door alignment and helps maintain a tight seal. What it does:

• Supports the weight of the lower door corner and provides a pivot point for opening/closing.
• Keeps the door aligned so the gasket can seal properly.
• Worn or damaged hinges can cause door sag, uneven gaps, rubbing, or difficulty closing.
• Restoring a solid hinge reduces stress on the door and latch for more reliable operation.

• Disconnect power to the appliance and remove food/items from the door before starting.
• Always support the door while removing/installing the hinge to prevent dropping or damage.
• Use the correct tools and hardware; tighten fasteners snugly but avoid over-torquing.
• After installation, check door alignment and seal; adjust as needed for proper operation.

This cabinet corner trim is a replacement corner piece that restores the finished edge of the appliance cabinet for a clean, protected look. It helps cover damaged or worn corners and improves the cabinet's appearance. What it does:

• Replaces a cracked, chipped or missing cabinet corner trim to restore a smooth finished edge
• Protects the cabinet corner from dings, moisture, and dirt buildup
• Improves cosmetic appearance by covering exposed cabinet edges
• Keeps adjacent panels aligned and reduces visible gaps around the cabinet corner

• Disconnect power to the appliance before working near electrical components
• Remove any damaged trim and clean the mounting area before installing the new piece
• Trim may snap into place or secure with screws/adhesive depending on model—use appropriate fasteners

This refrigerator bracket is the OEM mounting piece that secures a specific internal assembly in place. Replacing a cracked or missing bracket restores a solid fit, proper alignment, and smooth, rattle-free operation of the attached component.

• Provides a rigid mounting point for the designated refrigerator component
• Maintains proper alignment to help the assembly operate correctly
• Helps reduce vibration and movement that can cause noise or wear
• Typical signs of failure: broken tabs, stripped holes, loose or misaligned parts

• Disconnect power; turn off water supply if working near ice/water components
• Access the area per your product's diagram; retain and reuse existing screws/fasteners
• Transfer any clips, spacers, or grommets from the old bracket to the new one
• The mounted component seats fully and operates before reassembling panels/shelves

This hinge bracket supports and aligns the refrigerator door at the pivot point, helping the door open and close smoothly and seal properly. Replacing a worn bracket can restore stable door movement and reduce air leaks.

• Provides rigid support for the door hinge to maintain proper alignment
• Helps ensure a consistent door seal to prevent temperature fluctuations
• Common fix for loose, sagging, or misaligned doors
• Helps if the door makes popping/grinding noises when opening or closing

• Unplug the refrigerator and wear cut-resistant gloves
• Support the door before removing hinge fasteners to prevent drops
• Transfer and reinstall existing screws/hinge pin as needed
• Check door alignment and gasket contact after installation

This upper hinge cover protects and finishes the refrigerator door hinge area for a clean look and to keep the hinge free of debris. Replaces cracked or missing covers to restore appearance and help prevent dirt buildup. What it does

• Covers the upper door hinge to shield the hinge mechanism from dust and spills
• Prevents debris from collecting around the hinge that can affect movement
• Restores finished appearance when original cover is broken, cracked, or lost
• Helps keep hinge area easier to clean and maintain

• Snap-on/slide-on replacement; no special tools typically required
• Align cover over the upper hinge and press until it seats securely
• Inspect hinge for damage before installing; replace hinge hardware if worn
• Disconnect power only if needed for adjacent service; follow manufacturer safety guidance

This upper hinge cover protects and conceals the refrigerator's top door hinge for a finished look and safer edges. It restores proper appearance after damage or wear and helps keep the hinge area clean. What it does:

• Covers the upper door hinge to hide hardware and reduce dirt buildup
• Protects fingers and clothing from exposed hinge parts
• Restores cabinet appearance when the original cover is cracked or missing
• Works with the existing hinge assembly; does not affect door alignment when intact

• One upper hinge cover

• Designed to snap or slide into place over the upper hinge; may require removing the hinge trim or loosening the hinge for access
• Use basic hand tools; avoid over-tightening hinge fasteners after reassembly
• Disconnect power to the appliance if required for safe access to the hinge area
• Replace damaged components before installing the cover

Specs: 1.40`` long

Specs: Hex head ,1/4-20 x 5/8

This turntable roller assembly sits under the glass tray to support and guide it as it rotates. Replacing a worn or damaged ring helps restore smooth tray movement for more even heating and dependable microwave performance.

• Supports the glass tray and allows smooth, consistent rotation
• Helps prevent tray wobble, binding, or scraping noises
• Can address issues like the tray not turning or uneven cooking
• Replaces cracked, warped, or missing roller rings

• Disconnect power before servicing
• Remove the glass tray, lift out the old ring, and clean the cavity floor
• Place the new ring wheels-down, seat the tray on the coupler, and test rotation
• Do not operate the microwave without the roller ring and tray properly installed

This replacement screw fastens appliance components such as panels, brackets, and covers. Installing a new fastener restores a snug, rattle-free fit when the original screw is missing, stripped, or corroded.

• Secures covers, brackets, or trim to the cabinet or liner
• Replaces missing, stripped, or rusted hardware
• Helps reduce vibration and rattling from loose parts
• Supports proper alignment and stability of assemblies

• Disconnect power before servicing the appliance
• Use the correct driver/bit and start threads by hand to avoid cross-threading
• Do not overtighten, especially into plastic or thin sheet metal
• Retain and reinstall any original washers or spacers, if present

This board-switch is the user control/selector module that sends settings signals to an appliance's control system, restoring reliable selection of cook or cycle options and user-input functions. What it does

• Acts as the selector/control interface that registers knob or button selections and sends corresponding signals to the main control
• Re-establishes lost or intermittent selection responses when worn contacts or a failed switch board prevent input recognition
• Can fix symptoms such as unresponsive selector buttons/knobs, inability to change cycles or modes, or intermittent control inputs
• Works as the electrical switching/selector component rather than a full electronic control board

• One board-switch assembly as shown

• High-level replacement: power must be disconnected at the breaker or plug before access and replacement
• Handle the board by edges; avoid contact with components and use anti-static precautions if possible
• Installation may require removal of the control console or panel and basic hand tools; keep screws and connectors organized

This factory screw fastens refrigerator components and panels. It replaces missing or damaged hardware so parts stay aligned and secure, reducing looseness and rattles caused by vibration. What it does:

• Secures panels, brackets, and trim per your model's design
• Helps maintain alignment and reduce vibration-related loosening or noise
• Replaces missing, stripped, or corroded hardware
• Restores a snug fit when threads or heads are worn

• One screw

• Disconnect power; turn off the water supply if working near ice or dispenser systems
• Use the correct driver; start threading by hand to avoid cross-threading
• Tighten until snug—do not overtighten to prevent stripping or cracking adjacent plastic
• Refer to your model's diagram to confirm location and quantity used

This lower kickplate grille covers the refrigerator's toe-kick opening to protect components and finish the appliance's front. It restores appearance and maintains proper airflow through the cabinet bottom. What it does:

• Covers and protects the lower front area and components behind the toe kick
• Helps direct airflow under the cabinet where condenser/venting passages are located
• Replaces cracked, broken, bent, or missing lower grille pieces that leave the opening exposed
• Restores a finished look to the appliance front

• One lower kickplate grille

• Disconnect power to the appliance before starting any work
• Remove the old kickplate by releasing retained clips or fasteners, then align and secure the replacement
• Use gentle pressure to avoid bending the grille or damaging adjacent finishes
• Replace with OEM-specified hardware

This factory fastener secures appliance panels and components. Replace a missing, stripped, or corroded screw to restore a tight, rattle-free fit and keep brackets and covers properly aligned.

• Fastens panels, brackets, and internal parts as specified by the manufacturer
• Helps maintain alignment and reduces vibration/rattling
• Replace if the head is stripped, threads are damaged, or corrosion is present
• Symptoms include loose/missing hardware, gaps, or rattling during operation

• Disconnect power; shut off gas/water if applicable before servicing
• Use the correct driver/bit size to avoid stripping the head
• Start threads by hand to prevent cross-threading; do not overtighten
• Match screw length/thread to the location; replace in sets when required

This replacement rear compressor base roller supports the refrigerator compressor on the cabinet rear base, helping keep the compressor properly seated and reducing wear from vibration and movement. What it does

• Provides a rolling support under the compressor to keep it aligned and off the cabinet floor
• Helps reduce vibration and rattling that can occur from a loose or worn compressor mount
• Prevents compressor body from dragging or scraping the cabinet base
• Commonly replaced when the roller is cracked, worn flat, missing, or causing noise

• Disconnect power to the appliance before starting any work
• Support or secure the compressor and cabinet before removing the old roller to avoid sudden movement
• Basic hand tools usually required; inspect mounting hardware and replace any damaged fasteners
• Do not attempt sealed-system repairs.

This rivet is a metal fastener used to permanently secure panels, brackets, or internal components in your appliance. Replacing a damaged or missing rivet restores a tight fit and helps prevent vibration, rattles, and looseness.

• Permanently joins thin metal parts where screws or nuts aren't used
• Maintains alignment and structural integrity of housings and frames
• Helpful when panels or components are loose, rattling, or won't stay secured
• Direct replacement for a worn, broken, corroded, or drilled-out factory rivet

• Disconnect power and shut off gas/water (as applicable) before servicing
• Support the part being fastened; drill out the old rivet head if needed
• A hand riveter/rivet tool may be required to set the new rivet
• Wear eye and hand protection during drilling/riveting

This cover assembly replaces a damaged or missing cover on your appliance, protecting internal components and restoring a clean, finished appearance. Use it when the original is cracked, loose, or no longer secures properly.

• Shields internal parts from debris, spills, and accidental contact
• Helps keep components enclosed and aligned for reliable operation
• Restores the appliance's finished look after damage or wear
• Common signs of failure: cracks, broken or missing tabs, discoloration, rattling, or a cover that won't stay in place

• Disconnect power before servicing; shut off water supply if working near water connections
• Remove retaining screws or release tabs; note the orientation of the original cover
• Transfer and reuse original screws, clips, or seals if required
• Do not overtighten fasteners into plastic; ensure all tabs fully engage before testing

This coil cover seal is a molded gasket that fits around the evaporator/coil cover to help keep airflow directed and reduce moisture and frost buildup. It restores the cover's sealing surface for more consistent cooling performance. What it does:

• Seals the evaporator/coil cover to help maintain proper airflow through the coil
• Helps reduce frost or ice buildup by keeping moist air away from cold coil surfaces
• Can prevent water dripping or pooling inside the cabinet near the coil
• Restores a tighter seal after a cracked, torn, or compressed gasket reduces effectiveness

• Disconnect power to the appliance before starting any repair
• You may need to remove the evaporator/coil cover or access panel to reach the seal
• Clean the mating surfaces and dry thoroughly before installing the new seal
• Handle the gasket gently and press evenly to seat; avoid stretching or sharp tools that could damage the part

This replacement screw secures refrigerator components such as brackets, trims, and covers. Replace missing or stripped hardware to keep parts tight and aligned, helping eliminate rattles and restoring a solid, reliable fit.

• Fastens interior or exterior components to the cabinet or doors
• Replaces missing, rusty, or stripped hardware
• Helps reduce vibration noises from loose parts
• Restores proper fit and alignment of panels, trims, or covers

• Disconnect power; turn off water supply if working near the dispenser or ice system
• Retain and reuse any original spacers or washers
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace one fastener at a time to maintain alignment

This light switch controls the interior lamp, turning it on when the refrigerator door opens and off when it closes. Replace a worn or stuck switch to restore proper lighting and prevent the light from staying on. What it does:

• Door-activated plunger switch that opens/closes power to the interior light
• Restores interior lighting when the door is opened
• Resolves lights that stay on with the door closed, which can warm the compartment
• Addresses intermittent or flickering light from worn contacts

• 1 light switch

• Disconnect power before servicing
• Gently pry the old switch from the liner or remove the control housing as required for access
• Transfer the wire connectors to the new switch, matching positions
• Press the new switch fully into place, restore power, and test light operation

The Rear Crisper Cover Support is an OEM part for Frigidaire refrigerators. It plays a key role in supporting the crisper cover, which is the shelf that holds the crisper drawers. This part ensures that the cover remains stable and level, providing reliable support for storing fresh produce and other items in the crisper drawers.

Symptoms of a bad Rear Crisper Cover Support include:

• The crisper cover sagging or failing to stay in place
• Difficulty sliding the crisper drawers in and out
• Noticeable instability or wobbling of the cover
• Cracks or breakage where the support attaches to the refrigerator wall

Causes of a bad Rear Crisper Cover Support can involve regular wear and tear, excessive weight placed on the crisper cover, or accidental damage during cleaning or handling.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Front Crisper Cover Support is an OEM replacement part for Frigidaire refrigerators. It is a component that provides structural integrity and support for the crisper cover or glass shelf located in the refrigerator's crisper drawers.

Symptoms of a faulty Front Crisper Cover Support include:

• Sagging or misaligned crisper cover or glass shelf
• Difficulty in opening or closing the crisper drawers
• Visible cracks, breaks, or damage to the support itself

Causes of a bad front crisper cover support can include normal wear and tear, physical impact or mishandling, or exposure to excessive moisture or temperature fluctuations.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore refrigerator models.

Specs: .875`` long

Color: Black

This part number contains one (1) screw.