Parts for Frigidaire FRT22INLHC1: 03 - Cabinet Parts

Mounts the evaporator fan and directs airflow across the coil in your refrigerator. Replace if cracked, broken, or missing to restore proper function.

This fan motor mounting bushing is used in refrigerator fan motor assemblies to prevent vibrations between the fan motor and the surrounding components. Over time, the rubber on the bushing may become cracked or broken and fall off. Loud noises coming from the refrigerator's freezer section where it is mounted are a good indicator that the bushing needs to be replaced. To start, disconnect the refrigerator's power and empty the refrigerator and freezer's contents into an ice chest to keep them cold until the motor mount bushing is replaced. Open the freezer door and remove the plastic access panel on the back wall; the fan blade and motor are located behind it. Gently pull the fan blade off the center post. Remove the screws holding the motor in place and remove the motor. Take the old bushing off and install the new bushing. Replace the panel. Put the food contents back inside the freezer and refrigerator and restore the power.This motor mounting bushing is an authentic OEM replacement part sourced directly from the manufacturer. It is sold individually. It is designed for use in refrigerators manufactured by Frigidaire, Kenmore, Gibson, and Kelvinator.

Front evaporator fan motor mounting bracket

Covers the factory test opening on your refrigerator cabinet or liner. Replace if missing, cracked, or damaged to restore a finished look and seal.

Fix squealing freezer noise or warm fridge temps? Your evaporator fan motor may have failed. Most DIYers replace this in 10-15 minutes with basic tools.

Secures moving components and provides a stable pivot surface in your refrigerator. Replace when worn, broken, or causing looseness and poor alignment.

Black button plug that covers upper hinge mounting holes on your refrigerator. Replace if original plug is missing, cracked, or broken for a clean finish.

Drain tube spout for refrigerators. Directs defrost water from drain into drip pan. Replace if cracked, broken, or missing to prevent leaks or water damage.

Hex head bolt that secures the adjustment roller assembly to your refrigerator. Replace if stripped, missing, or damaged to restore proper leveling.

Black center hinge bracket for refrigerators. Mounts between fresh food and freezer doors. Replace if cracked, broken, or causing door misalignment.

Center hinge pin for refrigerator doors. Replaces worn, broken, or missing pins that secure the door hinge assembly. Essential structural component.

Black corner trim cap for refrigerator cabinet. Covers and protects cabinet corner edges. Replace if cracked, broken, or missing for a clean finish.

Black plastic cover that conceals the upper door hinge on your refrigerator. Replace if cracked, broken, discolored, or missing for a clean finish.

Rear roller assembly for refrigerators. Mounts under the back of the unit to allow smooth rolling and positioning. Replace if cracked, worn, or broken.

Replacement screw for various appliances. Used to secure panels, components, or housing. Replace if stripped, corroded, missing, or damaged hardware.

Replacement screw for various appliances. Used to secure panels, components, or housing. Replace if stripped, corroded, missing, or damaged hardware.

Secures panels, brackets, and handles in refrigerators and other appliances. Replace missing or stripped screws to restore secure mounting.

Factory fastener that secures panels, brackets, and internal components. Replace missing, stripped, or corroded screws to restore tight fit and eliminate rattling.

Replacement mounting screw for securing brackets, trims, covers, and components inside your refrigerator. Replace missing, stripped, or lost hardware.

Refrigerator ice maker mounting bracket secures the ice maker assembly to the freezer wall. Replace if cracked, broken, or missing to properly support installation.

Black plastic plug button that covers the center hinge hole on your refrigerator. Replaces missing, cracked, or damaged hinge hole cover inserts.

The Crisper Shelf Support is an OEM part for Frigidaire refrigerators. It is designed to hold the crisper shelf securely in place, providing stable support for the storage of fruits and vegetables.

Over time, the crisper shelf support can become worn or damaged due to regular use, heavy loads, or accidental impacts. If the support breaks or fails, it can lead to an unstable or sagging crisper shelf.

Symptoms of a bad crisper shelf support include:

• The crisper shelf not sitting level
• The shelf falling out of place or not staying securely in position
• Difficulty in inserting or removing the crisper drawer
• Visible cracks or damage to the support

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Nylon washer for the evaporator fan motor shaft in refrigerators. Replace if worn, cracked, or missing to ensure proper fan alignment and operation.

Replacement shelf support plug insert for freezer shelves. Installs into shelf brackets to secure wire racks. Order when original is cracked or missing.

Lower hinge tapping plate for refrigerators. Secures the bottom door hinge to the cabinet frame. Replace if cracked, stripped, or damaged.

Touch-up paint for appliances to cover scratches, chips, and worn areas on exterior surfaces. Restores appearance of refrigerators, ranges, and more.