Parts for Thermador PCG486GD/05: Cabinet Parts

This factory fixing kit supplies the OEM hardware required to secure the appliance or designated components during installation or service. Replacing missing or damaged fasteners restores a solid, aligned mount so the unit stays stable without shifting, rattling, or gaps.

• Provides the correct hardware to fasten parts per your model's installation or service instructions
• Replaces stripped, corroded, or missing screws/clips that lead to looseness
• Helps maintain alignment and clearances to prevent gaps, rattles, or vibration
• Typical symptoms: loose mounting, panels that shift, or movement when opening/closing doors or drawers

• Disconnect power; shut off water or gas if applicable before starting work
• Follow the model-specific installation/service manual for attachment points and sequence; use the proper driver bit and do not overtighten
• Verify the unit is level and securely anchored; check clearances and operation after securing

This OEM replacement pin is a small hardware fastener used to secure or pivot mating components within the appliance. Replacing a worn or missing pin restores proper alignment and reliable movement of the affected part or linkage.

• Serves as an axle/retainer for hinges, brackets, or linkages
• Maintains alignment of moving parts to reduce wobble or binding
• When bent, worn, or missing, you may notice looseness, rattling, misalignment, or difficulty opening/closing related components
• Direct-fit OEM replacement for the specified application

• Disconnect electrical power and shut off water or gas before servicing
• Support the component being serviced to prevent strain or damage during removal/installation
• Note the original orientation and retain any washers, clips, or spacers for transfer to the new pin
• Inspect mating holes/bushings; replace related worn parts to ensure proper fit and operation

The Re-Ignition Spark Module is an OEM replacement part Bosch ranges. It is an electronic component that generates sparks to reliably light the burners on a gas cooktop. Consistent sparking is necessary for fully lighting the burner flames and facilitating safe and efficient cooking operation.

Causes of a bad spark module can include normal component wear over time or damage from exposure to moisture or other contaminants. Improper cleaning methods could potentially impact performance.  

Symptoms of a bad spark module include:

• Burners not lighting or sparking when the knob is turned 
• Unreliable or intermittent lighting requiring multiple attempts
• Burner flames that emit an inconsistent or unstable pattern
• Sparks appearing outside of the burner ring pose a safety risk

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore model

This support mounting bracket holds and stabilizes internal components to keep the appliance assembly aligned and secure. Replaces worn or broken supports to reduce movement and restore proper fit. What it does:

• Provides structural support for the appliance's internal panel or assembly
• Prevents sagging, misalignment, or excessive vibration of the supported part
• Helps eliminate rattling or shifting noises caused by a damaged bracket
• Restores secure attachment points for panels or components

• Disconnect power and water before starting any repair
• Use the OEM fasteners and follow component alignment when installing
• Wear gloves to protect against sharp edges; handle parts carefully

This support mounting bracket secures internal components and helps maintain proper alignment for reliable operation. It replaces worn or damaged supports to reduce rattling and prevent part misalignment. What it does:

• Holds and stabilizes internal assemblies to keep components aligned during use
• Reduces vibration and rattling caused by loose or broken supports
• Helps prevent improper operation from misaligned parts
• Can be replaced when support is cracked, bent, or visibly worn

• Disconnect power and water before starting any repair
• Inspect adjacent parts for wear; replace damaged components to prevent repeat failure
• Use manufacturer-recommended fasteners and torque; do not overtighten

This cable harness routes power and signals between key components to restore reliable electrical connections and normal appliance operation. Replace a damaged harness to fix intermittent power, control failures, or non-responsive functions. What it does:

• Provides the multi-conductor wiring path that links control boards, sensors, and motors
• Carries low-voltage signals and/or line power needed for normal appliance functions
• Commonly replaced when wires or connectors are damaged, burned, or corroded
• Can resolve symptoms such as intermittent operation, no power to components, or control errors

• Disconnect all power before accessing wiring or controls to avoid shock
• Route harness along original clips and channels to prevent pinching or chafing
• Inspect connectors for damage and replace if terminals are loose or burned