Parts for Ge ZDBR240HAPS: Cabinet & Shelves Parts

This temperature sensor (thermistor) senses cabinet/evaporator temperature so the control can maintain proper cooling. Replaces a failed sensor to help restore accurate temperature readings and stable refrigerator operation. What it does:

• Measures internal temperature and sends readings to the control board
• Helps control compressor and fan cycling for consistent cooling
• Commonly associated with refrigerators that run continuously, cool inconsistently, or show incorrect temperature
• Can affect defrost cycles if the evaporator reading is incorrect

• Disconnect power before accessing components to avoid electrical shock
• Handle the sensor and lead carefully; avoid kinking or sharp bends in the wire
• Ensure the connector is fully seated and any mounting clip is snug but not overtightened
• Some models require removing interior panels or the evaporator cover for access

This short bottle rack replaces a broken or cracked door-mounted bottle holder to keep bottles and tall items organized and secure on the refrigerator door. Durable replacement that restores proper door storage and prevents bottles from tipping or sliding. What it does:

• Replaces damaged or missing short bottle rack on the refrigerator door
• Secures bottles, beverage containers and tall items so they stay upright during door use
• Prevents items from sliding or falling when the door is opened or closed
• Helps restore organized, usable door storage

• One short bottle rack

• Remove all items from the door shelf area before beginning
• Inspect door rail/clips and mounting points; align rack and press or fasten into place per original mounting method
• If clips or fasteners are damaged, replace them before installing the rack
• Refer to the refrigerator's service or owner's manual for model-specific installation guidance and safety precautions

This hinge and cam riser assembly replaces the upper hinge support that helps properly position and pivot the refrigerator door for smooth opening and a correct seal. It restores door alignment and stable hinge operation. What it does:

• Supports the top door hinge and provides the cam surface the hinge pin rides on
• Restores proper door alignment and helps prevent door sag or uneven gaps
• Reduces rubbing, binding, or noisy hinge movement caused by a worn riser
• Helps the door close fully so the gasket can seal properly

• One hinge and cam riser assembly

• Disconnect power or follow appliance safety guidance; support or brace the door before removing the hinge
• Loosen and remove top hinge fasteners to replace the riser; keep hardware for reinstallation
• Verify correct orientation and alignment before fully tightening fasteners; do not overtighten

This short frame guide helps support and guide the refrigerator drawer or bin for smooth opening and stable operation. It replaces a worn or broken guide to restore proper alignment and reduce drawer sticking or wobble. What it does:

• Guides and supports the drawer/bin along its track for consistent movement
• Helps prevent drawer misalignment, binding, and uneven wear
• Restores secure seating and reduces rattling or shifting during use
• Works as the short/secondary guide where appliances use paired guides

• Disconnect power to the appliance before servicing to avoid shock or injury
• Typical installation requires removing the drawer/bin and fastening the guide with original screws or clips
• Retain and reuse any original hardware unless replacement is explicitly supplied

This right-side upper door hinge secures the refrigerator door at the top and helps it swing smoothly while keeping alignment. A direct-fit hinge designed to restore proper door operation and prevent sagging or gaps that let cold air escape. What it does:

• Provides a durable pivot point for the refrigerator door to open and close reliably
• Restores correct door alignment to prevent rubbing, uneven sealing, or floor contact
• Helps maintain a tight door seal to preserve internal temperature and efficiency
• Replaces worn or damaged hinge that causes door sag, binding, or noisy operation

• One upper hinge, right side

• Disconnect power and empty door contents before starting
• Retain original mounting hardware if undamaged; replace hardware only if explicitly supplied
• Support the door while removing/installing the hinge to prevent injury or damage
• Check door alignment and seal after installation; adjust per manufacturer instructions

This reverse door hinge kit lets you change the swing direction of a compatible refrigerator door, restoring proper alignment and sealing after a hinge-side change. It's a direct replacement designed for straightforward door reversal. What it does:

• Reverses the door swing so the door opens from the opposite side
• Restores proper door alignment and helps seal the gasket for consistent cooling
• Replaces worn or bent hinge components that cause sagging or sticking
• Useful when relocating the refrigerator or changing kitchen layout

• Disconnect power and remove food from door area before starting
• Follow the refrigerator's service manual for hinge removal and reinstallation steps
• Use appropriate tools and support the door while removing/installing hinges to avoid injury or damage
• If screws or trim pieces are missing from the kit, verify kit contents against the appliance parts list before installation

A single replacement frame screw that secures the appliance's front frame or trim so panels stay aligned and stable. Use this OEM-style screw to replace a missing or damaged fastener and restore a snug, rattle-free fit. What it does:

• Secures the front frame or trim to the appliance cabinet to maintain proper panel alignment
• Stops loose or vibrating trim that can cause noise or visible gaps
• Replaces stripped, corroded, or missing screws that prevent panels from seating correctly
• Small hardware solution for restoring proper fit and finish after repairs

• Turn off and unplug the appliance (or shut off power at the breaker) before accessing panels
• Use the correct driver bit and hold the trim firmly to avoid stripping the head
• Do not overtighten; snug the screw until the panel is flush without distorting the trim
• If existing holes or threads are damaged, inspect for necessary thread repair or replacement parts

This temperature control bulb cover protects the refrigerator/freezer sensing bulb for reliable temperature readings and helps maintain consistent cooling. It replaces a damaged or missing bulb cover to restore proper sensor protection. What it does

• Shields the thermostat sensing bulb from contact, vibration, and accidental damage
• Helps the temperature control sense actual internal temperature for more consistent operation
• Commonly used when a cracked, missing, or deteriorated cover causes temperature fluctuations or inaccurate readings
• Compatible with thermostats that use an external sensing bulb and capillary tube design

• Disconnect power before servicing the appliance to avoid shock or injury
• Handle the sensing bulb and capillary tube gently; do not bend or kink the tube
• Install into the location of the original cover; may require removing interior panels or shelving for access