Parts for Briggs & Stratton 44K700 (0026-0124): Carburetor / Muffler Parts

Prevents oil leaks around the crankshaft in small gas engines. Replace if oil seeps from the bottom of the engine. Verify fit with your model number.

Flange screw for lawn and garden engines. Distributes connection force over a larger area. Replace if threads are stripped, head is damaged, or screw is missing.

Fix oil leaks or perform routine oil changes with this engine oil drain plug. Threads into the oil tank base for secure drainage. Simple DIY repair.

Engine won't restart after hitting an object? A sheared flywheel key is often the cause. This small part keeps the flywheel connected to the crankshaft.

This exhaust valve is a genuine Midwest Engine part, sold individually. This exhaust valve can be used as a replacement part for a variety of small engine outdoor appliances including lawn mowers, snowblowers, lawn tractors, and wood chippers. The purpose of an exhaust valve is to provide a channel for the burned gas to pass outside of the appliance and out into the air.The exhaust valve might have to be replaced at some point if it can no longer provide a passageway for burned gas to pass through on its way out of the appliance. If the exhaust valve has been blocked up, punctured, cracked, or warped, the component should be removed and replaced by this genuine OEM replacement part. It is a simple repair process that will take only a few minutes. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. Always unplug the appliance before performing any kind of repair or replacement. Sourced directly from the manufacturer, this component is a genuine replacement part that is sold individually. This exhaust valve is compatible with the following outdoor appliance brands: Midwest Engine, Briggs & Stratton, Toro, Cub Cadet, MTD, and Simplicity.

Replace a worn keeper valve if your small engine has valve train noise or poor compression. This small retaining clip secures valves in lawn mowers and outdoor power equipment.

Protects your lawn tractor engine from debris and dirt that could cause damage. Replace if cracked, broken, or clogged to maintain proper airflow and engine protection. Verify fit with your model number before ordering.

Fix engine flooding or hard starting with this float needle valve. Controls fuel flow in the carburetor. Common DIY repair, moderate difficulty.

Main jet for lawn and garden engine carburetors. Installs inside the carburetor bowl to regulate fuel flow. Replace if clogged, damaged, or missing.

Carburetor main jet for lawn and garden engines. Installs in the carburetor to regulate fuel flow. Replace if clogged, damaged, or missing.

Fix engine starting problems, rough idling, or stalling with this carburetor. Common repair for small engines that won't run smoothly or start easily.

Fix engine starting problems or rough idling with this float carburetor. Direct replacement restores proper fuel delivery. Moderate DIY repair.

Small metal hex nut for lawn mower engines. Secures components with threaded bolts. Replace if stripped, corroded, or missing during maintenance.

Mower won't start or runs poorly? Cracked or leaking fuel lines prevent proper fuel delivery. Simple 15-minute DIY repair restores engine performance.

Throttle link for lawn and garden engines. Connects the throttle control to the carburetor. Replace if bent, broken, or missing for proper operation.

This replacement governor gear is a certified genuine OEM part for a lawn tractor or mower engine. The governor is responsible for regulating the throttle. The interaction of the governor spring and governor gear works to position the throttle in such a way that it only allows a set amount of fuel into the carburetor. With less fuel in the carburetor, the engine will run slower. In this case, a slower engine means slower blade rotations. Like any gear, the governor gear has teeth the spin against another gear. Over time, the constant gnashing of gear teeth will cause the gears to wear down and possibly slip out of alignment. Once a gear is out of alignment, it will either stop working completely or degrade more quickly and should be replaced as soon as possible. Replacing the governor gear will require disassembling the engine cover and should be done in accordance with the owner's manual and manufacturer's instructions. This replacement governor gear is a high-quality part sourced from its original manufacturer. It is compatible with engines made by Briggs & Stratton and Toro. This shipment includes a governor gear and the brackets required for assembly.

Metal rear door panel for dryer drum access. Replaces cracked, dented, or rusted panels. Mounts to back of dryer cabinet for maintenance access.

Metal mounting screw for lawn and garden engines. Secures components together throughout the equipment. Replace when stripped, rusted, or missing.

The spark plug helps to start the engine by creating the spark that will cause the fuel to ignite in the engine during combustions. Over time, the spark plugs will become worn down and go bad. Multimeters are typically used to test the spark plugs. However, owners should also regularly look at the spark plugs to search for signs of corrosion that could indicate they are going to go bad. If they are not functioning properly, the engine will not fire and start. They will need to be replaced. This is an OEM replacement part that can be used on a range of small engines and lawn equipment from many brands. Compatible brands include Toro, Briggs & Stratton, Craftsman, Cub Cadet, Simplicity, and Snapper.

Engine won't start or runs rough? A cracked or missing spark plug boot causes misfiring and prevents proper ignition. Easy DIY replacement part.

Small but essential hardware nut for lawn and garden engines. Secures components in place when used with washers and screws. Replace if stripped or worn.

Engine won't start or flywheel won't turn? This ring gear screw secures the starter ring gear to enable proper engine cranking. Simple repair.

Fix a lawn mower that won't start or makes clunking noises when starting. This starter pinion gear engages the flywheel to crank your engine. DIY-friendly repair.

If your small engine won't start or has no spark, a faulty spark plug terminal may be the cause. This terminal connects the ignition coil to the plug.

This replacement valve seal is a genuine OEM part for a lawn tractor or mower. The valve stem is a type of valve that transfers oil into the cylinder and then immediately reseals due to the pressure in the chamber. However, if the seal is damaged, it will not close and oil will leak into the cylinder. If this happens, the cylinder head may become overly lubricated and not run well. This seal helps prevent that from happening. It fastens to the intake valve and valve stem keeper. Seals will naturally wear out over time due to stress and exposure to corrosive oxidizing agents in an engine. When this happens, the valve will leak oil. To test if the valve seal is compromised, look for whitish-grey smoke that indicates burning oil and also measure to see how much oil the engine is consuming. If the seal is breached, use a screwdriver and socket wrench set to change out the part. This top of the line replacement valve seal is compatible with Briggs & Stratton, Toro, and Lawn Boy lawn tractors. It is sourced from the original manufacturer and ships individually.

This replacement exhaust gasket is a certified genuine OEM part for a lawn tractor engine. This gasket helps to seal off the exhaust from the carburetor. For an engine to run, it must first mix fuel with air to prepare the fuel for combustion. By sealing off the exhaust, this gasket allows for fresh air to enter into the carburetor from outside the engine rather than from the exhaust. Gaskets often degrade over time due to the stress of pressure and heat. If the exhaust gasket breaks its seal, it can affect the engine's overall performance. Be on the lookout for an especially noisy engine that doesn't provide as much power and is less fuel efficient. There may also be a noticeable burning smell coming from the engine. To replace the exhaust gasket, use a socket wrench and wrench set to remove the air filter and blower housings, then remove the exhaust manifold and switch out the gasket. This replacement exhaust gasket is compatible with engines made by Toro, Briggs & Stratton, Murray, Snapper, and Simplicity. It comes sourced directly from its original manufacturer and does not include any additional hardware.

This replacement vacuum is identical to the original vacuum hose that comes with the machine. The purpose of the vacuum hose is to maintain proper airflow through the engine. The part is made from durable plastic, but it could still require replacement. If the vacuum hose becomes damaged or cracked, it could allow air into other parts of the system, where it should not be. This could cause the engine to have problems running properly or not to run at all. Owners should make it a point to regularly check the vacuum hose, as well as other parts of the engine, to ensure that everything is in good working order. If an issue is found with the vacuum hose, it should be replaced immediately. The genuine OEM vacuum hose can be used to replace the hose on lawn tractors and other small engines. Compatible brands include Briggs & Stratton, Cub Cadet, Toro, Murray, MTD, and Simplicity. Owners should check their manuals before buying to ensure they are getting the proper hose for their make and model.

This oil pump cover is a genuine Midwest Engine part, sold individually. This oil pump cover can be used as a replacement part for lawnmowers, snowblowers, wood chippers, and lawn tractors. It ensures that the oil pump can deliver oil to the engine without any excessive oil leakage. Symptoms of a damaged oil pump cover can include oil leakage in and around the cover, reduced oil pressure, and oil leakage in and around the intake manifold gasket. If any of these symptoms occur and are directly attributable to the oil pump cover, the part should be immediately replaced with this genuine OEM replacement part. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This is an OEM part sourced directly from the manufacturer, and it is sold individually. This Oil pump cover is compatible with the following outdoor appliance brands: Midwest Engine, Briggs & Stratton, Toro, Simplicity, Cub Cadet, Lawn-Boy, and MTD.

Replacement mounting screw for lawn and garden engines. Secures engine components and covers. Order when original is stripped, missing, or damaged.

This brush retainer is part of the starter motor on many types of lawn and garden machinery. It comes with both the retainer and a set of four brushes. The main job of the brush retainer is to hold a set of carbon brushes against the commutator bars located on the armature. If the brush retainer is worn, damaged, or improperly seated, it can cause problems with the equipment. The starter motor will not be able to get the proper amount of current from the battery.If the brush retainer might be causing problems, a visual inspection can be performed. A damaged brush retainer can wear down to the wire lead and become burned, pitted, or cracked. When the brush retainer is worn out, it can decrease engine performance, reduce braking, and cause the motor to lose power. This brush retainer is an authentic OEM replacement part sourced directly from the manufacturer. It is sold as an individual part. The retainer is made to be used with lawnmowers, snowblowers, tillers, and wood chippers created by Briggs & Stratton, Craftsman, Toro, Cub Cadet, Lawn-Boy, Snapper, MTD, and Simplicity.

Replacement mounting screw for lawn and garden engines. Secures engine components and housing. Needed when original fastener is stripped, lost, or damaged.