Parts for Lg LTCS20020W/00: Case Parts

This is a genuine replacement screw used to secure appliance panels and components. It restores proper fastening so panels and assemblies stay aligned and operate safely. What it does:

• Fastens panels, brackets, and small assemblies to maintain structural integrity
• Replaces missing or stripped screws that cause rattling or loose parts
• Helps stop vibration-related noise when used in its original mounting locations
• Matches the OEM fit to ensure proper alignment and clearance

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or component damage
• Disconnect power to the appliance before working on electrical components
• Replace all matching fasteners for even fit

This customized screw secures specific appliance components to maintain proper fit and prevent parts from loosening during normal use. Use it when replacing a missing or damaged fastener to restore secure assembly and reduce vibration. What it does:

• Fastens panels, brackets, or components to the appliance frame
• Keeps parts aligned to prevent rattling or movement during operation
• Replaces stripped, missing, or damaged screws that cause loose assemblies
• Helps maintain electrical and mechanical connections by holding parts in place

• Disconnect power and water before servicing the appliance
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; avoid overtightening which can strip threads or crack plastic
• Keep removed hardware organized for reassembly; replace any additional damaged fasteners

This customized screw is the manufacturer-specified fastener used to secure appliance components and panels at their mounting points. Replace a missing, stripped, or corroded original to restore a tight fit, proper alignment, and help eliminate vibration or rattling.

• Secures brackets, covers, and panels to the chassis at designated mounting points
• Maintains alignment and stability of the assembly during operation
• Helps address loose or rattling components caused by a missing or damaged fastener
• Direct replacement for the original fastener used in the specified location

• Disconnect power; shut off water before servicing
• Match head/length to the original; transfer any original clips or washers if used
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Tighten until snug—do not overtighten into plastic or thin sheet metal

The Drain Pipe Assembly is an OEM replacement part for LG refrigerators. It is a plastic tubing system that collects and removes liquid condensation from evaporator coils. Proper drainage is crucial to minimizing frost buildup and ensuring optimal cooling of food storage areas. 

Symptoms of a bad drain pipe assembly include:

• Excessive frost or ice accumulation inside the refrigerator
• Puddling or leaks detected near evaporator housing
• Slow draining allowing water to pool versus emptying fully
• Cracks or breaks in the tubing prevent complete fluid removal

Causes are typically mineral sediment clogging drainage paths or deteriorating plastic from constant use. This OEM LG replacement pipe restores reliable condensate removal to maintain peak efficiency.

This OEM LG part is also compatible with Sears/Kenmore. 

This adjustable leveling leg assembly supports and stabilizes the refrigerator. Replacing a worn or damaged leg restores proper leveling, reduces vibration and noise, and helps doors align and seal correctly.

• Provides height adjustment at the cabinet corner to level the appliance on uneven floors
• Helps prevent rocking, rattling, and excessive vibration
• Promotes proper door alignment and gasket sealing
• Replace if the foot is broken, missing, bent, or the threads are stripped and won't hold adjustment

• Disconnect power and turn off the water supply before servicing
• Protect the floor; with a helper, carefully tip and support the refrigerator
• Unscrew the old leg; hand-thread the new leg, then fine-tune height with a wrench until level
• Ensure both front legs share the load evenly and recheck door operation

This control case assembly is the replacement outer housing that holds and protects the appliance control board and user interface, restoring a secure fit and proper button/panel alignment for safe operation. What it does:

• Houses and protects the control board and associated electronics from dust, moisture, and accidental contact
• Keeps control panel buttons and switches properly aligned for reliable user input
• Prevents loose or rattling control components that can cause intermittent operation or noise
• Supports the front panel and display mounting for normal appearance and functionality

• Disconnect power to the appliance before starting any repair to avoid electric shock.
• Handle the control board and connectors carefully; avoid touching circuit traces or components.
• Basic hand tools are typically required to remove the panel and transfer the control board into the new housing.
• If the control board is damaged or shows corrosion, this part replaces only the housing unless otherwise specified.

The Shelf Assembly is an OEM part for LG refrigerators. This shelf assembly provides sturdy and reliable storage space within the refrigerator, allowing for the organization of food items and maximizing the use of the available space.

Causes of a bad shelf assembly can include regular wear and tear, overloading the shelf with heavy items, or accidental impacts that can cause cracks or breaks. A compromised shelf can reduce the overall storage efficiency and safety of the refrigerator.

Symptoms of a bad shelf assembly include:

• Cracks or breaks in the shelf material
• Difficulty in sliding or positioning the shelf
• The shelf not staying securely in place
• Visible warping or instability

This OEM LG part is also compatible with Sears/Kenmore models.

This freezer shelf assembly replaces a damaged or missing shelf to restore usable storage space and stable support for frozen items. It fits into freezer compartment shelving tracks and provides a flat, secure surface. What it does

• Replaces a broken, cracked or warped freezer shelf so food and containers sit level and stable
• Restores organized storage when an existing shelf is bent or missing
• Helps prevent items from tipping or spilling inside the freezer
• Matches OEM fit and mounting points for straightforward shelf support

• One freezer shelf assembly

• Remove food and unplug or switch off the appliance power before starting work
• Shelf typically slides or snaps into place on existing shelf supports; no special tools usually required
• Handle shelf carefully to avoid sharp edges on broken plastic or glass
• If mounting clips or supports are damaged, replace them before installing the new shelf

This small control knob mounts on the shutter mechanism so you can open, close, or fine-tune the setting with a simple turn. Replace a cracked, loose, or missing knob to restore smooth adjustment and a clean, finished look.

• Attaches to the shutter/damper shaft to select positions
• Provides a secure grip for easy, precise adjustment
• Common failure signs: cracked or stripped hub, loose fit, missing knob
• May cause difficulty adjusting the shutter or settings to slip

• Disconnect power if removing any covers or panels near electrical components
• Pull the old knob straight off; rock gently if stuck to avoid damaging the shaft
• Align the keyed/D-flat opening with the shaft and press firmly until fully seated
• The shutter moves smoothly through its full range

This shutter knob attaches to the crisper cover's humidity vent (shutter) and lets you open or close the airflow for produce storage. Replace a cracked or missing knob to restore smooth, precise adjustment of the drawer's vent. What it does:

• Connects to the shutter lever to adjust the vent position on the drawer cover
• Restores the ability to regulate airflow and moisture in the crisper
• Helps ensure the vent moves and stays in the selected setting
• Symptoms may include a broken or missing knob, a vent stuck in one position, or inability to adjust humidity

• 1 shutter knob

• Unplug the refrigerator before servicing; remove the crisper/drawer cover for access if needed
• Pull the old knob straight off the shutter shaft; align flats/tabs and press the new knob on until fully seated
• Do not force the knob—inspect the shutter lever for damage if it won't engage
• Verify smooth vent movement, then reassemble the cover and drawers

This vegetable tray stores and organizes produce in the refrigerator's fresh-food compartment. Replacing a cracked or missing bin restores usable space and smooth sliding access so fruits and vegetables stay contained and easy to reach.

• Holds fruits and vegetables in the crisper area
• Slides in/out on existing drawer rails for convenient access
• Helps keep items separated and contain minor spills
• Common symptoms: cracked or broken bin, missing tabs, drawer won't slide smoothly or stay seated

• Remove contents and slide the old drawer straight out
• Align the new drawer with the existing rails and push in until fully seated
• Handle nearby glass shelves carefully to prevent chips or breakage
• Disconnect power before working inside

Replace a cracked or missing cover with this cover assembly for the TV-designated section of your unit. It restores a clean, finished surface while helping protect internal components from dust, debris, and accidental contact.

• Shields internal components and wiring from dust and accidental contact
• Restores a clean, finished appearance in the covered area
• Helps retain adjacent parts that rely on the cover for proper positioning
• Common symptoms: broken or missing cover, loose/broken tabs, rattling/vibration, exposed components

• Disconnect power to the unit before servicing
• Remove any retaining screws or clips and keep them for reassembly
• Align tabs and mounting holes, seat the cover, and reinstall fasteners
• Do not overtighten screws to avoid cracking plastic; verify the cover sits flush

This cover support bracket secures an appliance cover or panel, restoring proper alignment and stability. Replacing a damaged support helps eliminate rattles and gaps so the cover seats correctly and stays in place.

• Provides structural support for the associated cover/panel
• Keeps the cover aligned and firmly seated against the cabinet
• Replaces a cracked, stripped, or missing support
• Symptoms include a loose or sagging cover, vibration/rattling noises, or covers that won't stay attached

• Disconnect power before servicing; allow any hot surfaces to cool and wear cut-resistant gloves
• Remove the cover/panel to access the support and retain all mounting hardware
• Install the new support, transferring screws or clips as needed
• Reinstall the cover and verify proper fit before restoring power

This replacement shelf glass restores a flat, sturdy surface inside your refrigerator for safe, organized food storage. Replace cracked, missing, or unstable glass to help contain spills and return your shelf to full strength.

• Provides a level, load-bearing surface for food containers in the compartment
• Helps contain leaks and spills so messes don't spread below
• Replace when glass is cracked, chipped, shattered, bowed, or missing
• Restores lost storage space and improves shelf stability

• If handling broken glass, unplug the refrigerator and wear cut-resistant gloves and eye protection.
• Remove items from the shelf, slide out the shelf/assembly, and carefully lift out the old glass.
• Clean any debris from the frame or supports. Set the new glass in place, ensuring it seats fully and is secure before reinstalling.

This Door Gasket Assembly creates a tight seal between the door and cabinet to keep cold air in and moisture out. Replace a worn or deformed gasket to restore proper sealing and help prevent frost and temperature swings.

• Forms the perimeter seal when the door closes to limit warm air infiltration
• Helps reduce frost, ice, and condensation around the door opening
• Supports stable internal temperatures for consistent cooling
• Common symptoms: torn or brittle gasket, visible gaps, door not closing flush, moisture or frost along the door edge

What's included: 1 door gasket Install notes:

• Disconnect power before beginning any repair
• Let the new gasket sit flat to relax, or gently warm it with a hair dryer on low to remove kinks
• Pull the old gasket from the retaining channel; press the new gasket fully into the groove, starting at the corners
• Close the door and check for uniform contact all around; warm and reshape as needed to improve the seal

This door basket snaps onto the inner door to hold jars, bottles, and condiments. Replacing a cracked or missing bin restores secure, organized storage and helps prevent items from tipping or falling when the door opens.

• Mounts on the refrigerator door to provide extra shelf storage
• Helps keep bottles and condiments upright and accessible
• Replaces bins with cracked plastic or broken locking tabs
• Fixes issues where the bin won't stay seated or falls off the door

What's included: 1 door basket Install notes:

• Remove contents and lift the old bin straight up to release from the door liner
• Align the new bin's rear hooks with the slots and press down until fully seated
• Verify placement with your model's parts diagram, as some positions use specific bins
• Let cold plastic warm to room temperature and avoid forcing to prevent cracks

This refrigerator guide aligns and supports a mating component so it travels smoothly and stays on track. Replacing a cracked or missing guide restores proper movement and helps prevent binding, jamming, or premature wear.

• Guides and stabilizes the movement of the associated part to ensure smooth travel
• Keeps components aligned to prevent rubbing, derailment, or gaps
• Common signs of failure: sticking or binding, wobbling/misalignment, or parts coming off track
• Visible damage such as cracks, broken tabs, or missing pieces on the guide

• Disconnect power; if working near a dispenser or water path, turn off the water supply
• Remove the access panel/bin as needed and retain any screws/clips
• Seat the new guide and reuse existing hardware; verify a secure fit
• Restore power and test the component's movement for smooth operation

The Door Stopper is an OEM part for LG refrigerators. It is a component located at the top of the refrigerator door frame. The stopper functions to securely cushion the door in the open position, preventing damage from accidental closing. 

Causes of a faulty stopper include wear from the door repeatedly contacting the part during normal use. Forceful door incidents could also bend or loosen the stopper over time.

Symptoms of a problematic door stopper are:

• The door not staying firmly in the open position
• Increased noise or vibration from the door while open
• Potential damage from an unrestrained door closing

This OEM LG part is also compatible with some Kenmore models.

This name plate is the exterior emblem that mounts to the appliance's front panel. It replaces a missing, cracked, or faded badge to restore a clean, factory look and cover the designated trim area.

• Attaches to the outer panel to display brand/series identification
• Restores a finished appearance where the original emblem sits
• Direct replacement for a lost, damaged, or worn badge
• Typical symptoms: missing emblem, loose or broken tabs, peeling, or discoloration

• Disconnect power before servicing the appliance
• Carefully remove the old emblem; release any tabs from behind or peel away remaining adhesive
• Clean and dry the mounting surface; remove all residue for best fit
• Align with the recess/holes and press evenly until fully seated

This door foam assembly replaces the inner insulating foam inside a refrigerator door to restore thermal seal and reduce condensation. It fits behind the door liner and helps maintain proper cooling by improving insulation. What it does

• Replaces deteriorated or damaged inner door insulation that can compress or break down over time
• Helps reduce condensation, frost buildup, and energy loss around the door cavity
• Restores proper spacing and support for the inner door liner and components
• Commonly used when foam is crushed, missing, or causing cold spots at the door

• One door foam assembly as shown

• Service should be performed with the refrigerator unplugged and empty the door if needed for access
• Remove door liner or trim panels per service manual to access and replace foam—handle panels and clips carefully to avoid damage
• Use manufacturer-recommended adhesive or fasteners if required; replace any damaged clips or seals

This door foam assembly replaces the inner insulating foam inside a refrigerator door to restore thermal seal and reduce condensation. It fits behind the door liner and helps maintain proper cooling by improving insulation. What it does

• Replaces deteriorated or damaged inner door insulation that can compress or break down over time
• Helps reduce condensation, frost buildup, and energy loss around the door cavity
• Restores proper spacing and support for the inner door liner and components
• Commonly used when foam is crushed, missing, or causing cold spots at the door

• One door foam assembly as shown

• Service should be performed with the refrigerator unplugged and empty the door if needed for access
• Remove door liner or trim panels per service manual to access and replace foam—handle panels and clips carefully to avoid damage
• Use manufacturer-recommended adhesive or fasteners if required; replace any damaged clips or seals

This door gasket assembly seals the refrigerator door to the cabinet to stop air and moisture leaks. A tight, even seal helps maintain interior temperature, reduce frost and condensation, and support efficient, reliable cooling performance.

• Creates a continuous perimeter seal between the door and cabinet
• Helps stabilize interior temperature and humidity
• Reduces frost, sweating, and condensation around the door opening
• Replaces gaskets that are torn, warped, brittle, or permanently flattened

• Disconnect power before servicing and clear items from the door.
• Let the new gasket warm to room temperature; relax bends with warm water or low heat if needed. Do not overheat.
• Press the gasket lip fully into the door channel, working evenly around all sides and corners.
• Close the door and verify uniform contact all around; reseat the gasket as needed for an even seal.

The Door Basket is an OEM accessory specifically designed for LG refrigerator doors containing vegetable drawers. This hanging basket provides auxiliary storage directly above crisper bins.

Causes of a bad door basket can include wear and tear over time compromising the mesh material, or damage from overloading reducing structural integrity.  

Symptoms of a bad door basket include:

• Holes or tears reducing usable capacity   
• Detached fasteners slipping off mounting brackets
• Warped contours no longer remain properly installed
• Insecure attachment inhibiting safe door openings  

Replace yours today with this genuine OEM LG basket to maximize organizational convenience. Sturdy brackets produce a snug, stable fit. Compatible with Samsung, GE, and Frigidaire refrigerators featuring dual-drawer doors, this upgrade complements any modern kitchen setup. Reliable performance preserves aesthetic appeal.

The Door Basket Assembly is an OEM component for LG refrigerators. It is located within the fresh food doors that securely hold bottles and containers of varying sizes.

Symptoms of a bad door basket assembly include:

• Items failing to remain securely placed or tipping easily within
• Warping or sagging basket components allowing gap openings
• Loose basket fittings inhibiting proper installation or removal
• Sections detaching or coming apart at seams over time

Causes can be normal wear and tear stresses from years of door openings/closings or impact damage.

This OEM LG part can also be used on Kenmore/Sears appliances. 

Upper hinge assembly that restores proper door pivot and alignment for smooth opening and closing. Replacing a worn or damaged upper hinge helps reduce sag, noise, and uneven sealing so the door closes correctly. What it does:

• Supports and pivots the refrigerator door for stable, controlled movement.
• Keeps the door aligned so the gasket seals evenly and the interior stays cold.
• Use when the door sags, binds, grinds, squeaks, or does not latch evenly.
• Replace bent, worn, or damaged hinge components that cause misalignment.

• Disconnect power and remove items from the door before starting; follow all safety precautions.
• Door removal and reinstallation often require a second person to support the door.
• Hinge orientation and hardware before tightening; follow the manufacturer service instructions for final alignment.
• Reuse or replace mounting screws and bushings as needed; do not overtighten fasteners.

Restore smooth, proper door movement with this Center Hinge Assembly. It supports the refrigerator door at the middle pivot point, helping maintain alignment and ensuring the door opens and closes correctly to seal out warm air.

• Supports the door at the center pivot for stable operation
• Helps correct issues like a sagging, misaligned, or rubbing door
• Can reduce squeaks or binding when opening/closing
• Helps the door seal contact the cabinet evenly for proper cooling

• Disconnect power and clear items from the door before service
• Support the door to prevent drops; remove hinge cover and mounting screws
• Transfer any shims/spacers in the original order for proper alignment
• After reassembly, verify door alignment and gasket seal

The Lower Hinge Assembly is an OEM part for LG refrigerators. This lower hinge safely and smoothly supports the weight of the refrigerator door.

Causes of a bad lower hinge can include loose or worn parts from years of use, damage from overloading doors with heavy items, or failure due to impact or bending stresses.  

Symptoms of a bad lower hinge include:

• Doors sagging or dropping over time
• Noisy squeaks or grinding sounds coming from hinges
• Difficulty opening and closing doors smoothly  
• Doors unable to stay open at various angles

Replace yours today with this genuine OEM LG assembly before further issues develop. This replacement part is compatible with Frigidaire, Samsung, and Kenmore models for a factory fit and function.

The Hinge Bushing is an OEM part for LG refrigerators. It serves as a crucial component in the door hinge mechanism, ensuring smooth and stable operation when opening and closing the refrigerator door.

You should replace this hinge bushing if it becomes worn out or damaged. Common causes of a bad hinge bushing include constant use leading to wear and tear, misalignment of the door, or physical damage due to impact.

Symptoms of a bad hinge bushing include:

• Difficulty in opening or closing the door
• The door sagging or not aligning properly
• Unusual noises like squeaking or grinding when the door is moved

This OEM LG part is also compatible with Sears/Kenmore.

This drum support roller helps the dryer drum rotate smoothly and quietly by supporting the drum shaft and reducing friction. Replacing a worn roller restores proper drum movement and reduces noise. What it does:

• Supports the dryer drum shaft so the drum turns evenly during operation
• Prevents metal-on-metal contact that causes squealing, grinding or scraping noises
• Helps maintain correct drum alignment to avoid rubbing or uneven wear
• Works with the dryer's axle and bearing system to enable smooth rotation

• One roller

• Disconnect power and move the dryer to a safe, well-lit work area before starting
• Access requires removing the dryer front or rear panel depending on model
• Inspect the drum shaft, bearing, and idler components and replace any worn parts at the same time
• Wear eye protection and gloves; test the dryer empty after installation to confirm quiet, smooth operation

A small retaining pin used to secure moving parts and keep components aligned for smooth operation. Replacing a worn or broken common pin can stop rattling and restore proper fit between linked parts. What it does:

• Holds or aligns two parts together so they move correctly and stay in position
• Helps prevent rattling, looseness, or parts slipping out of place
• Works as a simple mechanical fastener—no electronics involved

• One common pin

• Disconnect power to the appliance before beginning any service
• Keep track of small parts; lay out components in order to aid reassembly
• May require removal of trim or a hinge/retainer to access the pin—use basic hand tools
• If the pin is difficult to seat, do not force; inspect mating parts for damage

This small stopper installs in the refrigerator to limit the travel of a moving component and keep it securely in place. Replacing a broken or missing stopper prevents over-extension and helps maintain smooth, aligned operation.

• Limits the range of motion for a door, bin, or drawer to prevent over-opening or accidental removal
• Helps keep interior components aligned and operating smoothly
• Replace if cracked, missing, or deformed
• Common symptoms: drawer or bin slides out too far, door swings past normal range, or a broken plastic stop is found

• Disconnect power before servicing; remove or support the affected bin/drawer/door
• Note the old stopper's orientation and location before removal
• Transfer and reuse any original screws or clips if applicable
• Snap or fasten the new stopper in place and test for smooth movement

This holder secures the dryer-related assembly in place to reduce movement and wear, helping maintain proper alignment and quieter operation. It's a simple replacement that restores part stability in the appliance. What it does:

• Secures a dryer assembly or component to the appliance frame to prevent shifting
• Helps reduce vibration and rubbing noises caused by a loose part
• Maintains correct alignment so related parts operate smoothly
• Used when the existing holder is cracked, broken, or missing

• Disconnect power before replacing any dryer components to avoid shock or injury
• Access location and removal steps vary by model; follow the appliance's service manual or exploded view
• Keep fasteners and adjacent parts organized for reassembly; replace any damaged clips or screws

This motor bracket is the OEM-style mounting bracket that secures the appliance motor to the cabinet, keeping the motor aligned and reducing vibration for reliable operation. It helps restore proper motor support and stable running. What it does:

• Provides a secure mounting point to hold the motor in correct position
• Maintains motor alignment to prevent belt slip and uneven wear
• Reduces vibration and noise caused by a loose or damaged motor mount
• Can resolve symptoms such as unusual motor noise, excessive vibration, or motor movement during operation

• Disconnect power (and gas if applicable) before starting any repair
• Basic hand tools are typically required; follow the appliance service manual for access steps
• Inspect surrounding components (mounting fasteners, motor and belts) and replace any damaged parts

This guide assembly directs and stabilizes the refrigerator/freezer fan to ensure consistent airflow across the evaporator and cooling components. Replacing a damaged guide restores proper air circulation and helps reduce noise from an unsteady fan. What it does

• Holds and centers the fan blade to maintain efficient airflow through the evaporator coil
• Prevents fan wobble or contact with housing that can cause noise or mechanical wear
• Helps ensure even cooling and can reduce frost build-up caused by disrupted airflow
• Supports proper airflow that contributes to consistent temperatures in the cooling compartment

• One guide assembly

• Disconnect power before beginning any repair and follow the appliance manufacturer's safety instructions
• Access may require removing interior panels or the evaporator/fan housing; retain fasteners for reassembly
• Inspect adjacent components while replacing the guide to ensure full repair
• Use only compatible parts and avoid forcing plastic tabs; if clips or screws are damaged, replace them

This replacement fan blade mounts on the fan motor to move air for proper cooling. A cracked, loose, or damaged blade can cause noise and weak airflow—replacing it restores smooth, reliable air circulation. What it does:

• Drives airflow to help maintain stable temperatures throughout the appliance
• Supports efficient cooling by circulating air across key areas
• Common symptoms include rattling or scraping near the fan, vibration, or wobbling
• Replacement is recommended if the motor runs but the blade slips, doesn't spin, or is visibly damaged

• 1 fan blade

• Disconnect power before servicing
• Access the fan area by removing covers/shelves as needed
• Note blade orientation; pull the old blade straight off the shaft and press the new blade on until fully seated
• Spin the blade by hand to confirm clearances, reassemble, and restore power

This fan grille assembly covers and protects the appliance's circulation/cooling fan while guiding airflow through the compartment. Replacing a cracked or missing grille helps restore proper air movement and can reduce noise from contact or vibration.

• Protects fan blades from debris and accidental contact
• Directs airflow for efficient cooling/circulation
• Helps stabilize adjacent ducting/shrouds to reduce vibration
• Typical failure signs include rattling or scraping noises, weak airflow, temperature inconsistencies, or visible broken tabs/cracks

• Disconnect power before servicing; wear cut-resistant gloves
• Access the fan area and remove any shelves/panels as needed
• Remove mounting screws/clips, note orientation, and transfer any reusable seals or clips from the old grille
• Install the new grille and ensure the fan spins freely without contact before reassembly and restoring power

This is the main electronic controller assembly for the washer, responsible for managing cycles, timing and user inputs so the machine runs according to selected settings. Replacing a faulty controller restores normal control and cycle operation. What it does:

• Receives input from the control panel and starts/stops wash cycles and motor functions
• Sends signals to valves, motor and other components to regulate timing and operations
• Processes diagnostics and error reporting used by the washer's display/control interface
• Common symptoms of a failing controller: unresponsive controls, blank or frozen display, cycles that won't start or finish, or erratic/permanent error codes

• One controller assembly

• Disconnect power to the appliance before attempting any service to avoid shock or damage
• Handle the board carefully to avoid static discharge; ground yourself or use an ESD strap when possible
• Verify connector positions and secure all wiring harnesses; do not force connectors

The LG Refrigerator Condenser Fan Motor is an OEM part for LG refrigerators. It aids in heat dissipation by circulating air through the condenser coil to cool the refrigerant. 

Symptoms of a bad condenser fan motor include:

• The refrigerator failing to properly cool or maintaining inconsistent temperatures  
• Abnormally loud humming or buzzing noises emanating from the rear
• Reduced condenser fan blade speed or intermittent on/off cycles
• Refrigerant line temperatures being warmer than normal

Causes of a bad condenser fan motor can include failure of internal motor components, accumulated dirt/debris hindering fan blade movement, or damage due to impact.

This OEM LG part is also compatible with select Sears/Kenmore models. 

This motor support damper sits between the refrigerator's compressor and base to absorb vibration and movement. Replacing a worn damper helps quiet rattles and humming from the back of the cabinet and keeps the compressor properly supported.

• Cushions the compressor to reduce transmitted vibration and noise
• Helps quiet humming, buzzing, or rattling from the lower rear of the refrigerator
• Maintains proper compressor alignment and support on the base pan
• Common signs of wear: increased vibration/noise, a cracked or flattened damper, or noticeable compressor movement when running

• Unplug the refrigerator and pull it forward to access the rear; allow the compressor to cool before working
• Support the compressor to remove load from the mount before loosening hardware
• Replace the damper and tighten mounting hardware evenly without over-compressing the rubber
• Avoid bending or stressing refrigerant tubing; wear gloves and eye protection

The Rear Evaporator Motor Grommet is an OEM part for LG refrigerators. It's designed to secure and cushion the evaporator motor, ensuring it remains in place and operates quietly. This grommet plays a crucial role in minimizing vibrations and noise from the motor, which can otherwise lead to a disruptive refrigerator operation.

Causes of a bad Rear Evaporator Motor Grommet can result from deterioration due to cooling and thawing cycles in the refrigerator. Physical damage during cleaning or servicing may cause a loose motor fit.  

Symptoms of a malfunctioning Rear Evaporator Motor Grommet include:

• Unusual noises or vibrations from the back of the refrigerator.
• The evaporator motor shifting out of place, which can affect cooling efficiency.
• Increased wear on the evaporator motor due to lack of proper cushioning and support.

This OEM LG part is also compatible with some Kenmore models.

The Rear Evaporator Motor Grommet is an OEM part for LG refrigerators. It's designed to secure and cushion the evaporator motor, ensuring it remains in place and operates quietly. This grommet plays a crucial role in minimizing vibrations and noise from the motor, which can otherwise lead to a disruptive refrigerator operation.

Causes of a bad Rear Evaporator Motor Grommet can result from deterioration due to cooling and thawing cycles in the refrigerator. Physical damage during cleaning or servicing may cause a loose motor fit.  

Symptoms of a malfunctioning Rear Evaporator Motor Grommet include:

• Unusual noises or vibrations from the back of the refrigerator.
• The evaporator motor shifting out of place, which can affect cooling efficiency.
• Increased wear on the evaporator motor due to lack of proper cushioning and support.

This OEM LG part is also compatible with some Kenmore models.

The Front Evaporator Motor Grommet is an OEM part for LG refrigerators. This grommet cushions and secures the evaporator motor, reducing vibrations and noise during operation to ensure efficient cooling.

Causes of a bad grommet can include prolonged use leading to material fatigue, exposure to extreme temperatures, or physical damage from accidental impacts. A damaged grommet can result in increased noise and potential misalignment of the evaporator motor.

Symptoms of a bad evaporator motor grommet include:

• Increased noise from the refrigerator
• Vibrations or rattling sounds
• Poor cooling performance
• The evaporator motor becoming loose

This OEM LG part is also compatible with Sears/Kenmore.

This harness assembly routes power and signals between appliance components to restore electrical connections and normal operation. It replaces damaged or frayed wiring to stop intermittent power, control failures, or no-start conditions. What it does:

• Reconnects power and control circuits between major components
• Replaces damaged, burned, or frayed wires and connectors that cause intermittent or lost function
• Restores reliable signal paths to controls, sensors, and motors
• Helps resolve symptoms like sporadic operation, failure to start, or component non-response

• Disconnect power to the appliance before accessing electrical components.
• Match connectors and wire routing to the original harness during installation to avoid pin miswiring.
• Inspect connector pins and mating terminals for damage; replace the harness if pins are bent or corroded.

The Power Cord Assembly is an OEM replacement part for LG refrigerators. It includes the electrical cord and strain relief that links the refrigerator to an external power source.  

This power cord assembly safely delivers electricity from the wall outlet to the internal compressor and fan modules. It facilitates proper cooling functions through this transmission of alternating current.

Symptoms of a bad power cord can include:

• Abnormal sounds such as humming or buzzing from within 
• Tripped circuit breakers interfering with operations
• Indicators of cord damage like frays or exposed wiring
• Inconsistencies in interior temperature maintenance

Causes may involve normal wear over extended use, physical stress, or accidental damage to the cord insulation.  

Replacing the power cord assembly with this genuine LG OEM part restores a reliable electrical pathway. It ensures a continued power supply to keep foods fresh and frozen.

This sheath heater is the tubular heating element that generates hot air for drying cycles, restoring proper heat so laundry dries efficiently and cycles complete as expected. What it does

• Produces heat for the dryer's drum by passing current through a sealed tubular element
• Restores normal drying performance when a failed heater causes little or no heat
• Can stop uneven drying or long cycle times caused by a nonfunctional heating element
• Works with the dryer's internal thermal and safety controls to heat only as designed

• One sheath heater (tubular heating element)

• Turn off power to the appliance at the breaker (or unplug) before starting work
• Handle the element carefully and avoid bending or damaging the sheath and terminals
• Follow the dryer's service manual for removal and replacement

The PCB Assembly, Display is an OEM part for LG refrigerators. It is responsible for controlling the refrigerator's display functions and interface. This board monitors temperature and cycle settings and regulates the input/output of operational data to the control panel. It assists users by displaying temperatures, selections, and error codes.

Causes of a bad display board can include liquid damage, thermal stresses from opening/closing doors over time, and short circuits due to manufacturing defects.

Symptoms of a bad PCB assembly include:

• Faulty or unreadable control panel display
• Buttons not responding properly  
• Random error codes appearing
• Glitches in temperature or function display

This genuine LG replacement ensures dependable control panel performance. It preserves your investment and restores full refrigerator operations. This part is also compatible with Sears/Kenmore models utilizing LG components and controls.

The Main PCB Assembly is an OEM part for LG refrigerators. It is the circuit board responsible for controlling and regulating all electrical components and functions inside the refrigerator. The main PCB receives input signals and distributes power accordingly to run features such as the cooling system, ice maker, lights, dispensers and more.

Causes of a bad main PCB can include liquid damage, wear and tear over time, or component failure due to overheating or power surges.

Symptoms of a bad main PCB include:

• The refrigerator not cooling or icing
• Lights not working
• Dispensers and ice makers malfunctioning
• Strange noises coming from the electrical components
• Error codes displayed

This LG part is also compatible with some Kenmore models.