Parts for Lg LTCS20220W/03: Case Parts

This is a genuine replacement screw used to secure appliance panels and components. It restores proper fastening so panels and assemblies stay aligned and operate safely. What it does:

• Fastens panels, brackets, and small assemblies to maintain structural integrity
• Replaces missing or stripped screws that cause rattling or loose parts
• Helps stop vibration-related noise when used in its original mounting locations
• Matches the OEM fit to ensure proper alignment and clearance

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or component damage
• Disconnect power to the appliance before working on electrical components
• Replace all matching fasteners for even fit

This customized screw secures specific appliance components to maintain proper fit and prevent parts from loosening during normal use. Use it when replacing a missing or damaged fastener to restore secure assembly and reduce vibration. What it does:

• Fastens panels, brackets, or components to the appliance frame
• Keeps parts aligned to prevent rattling or movement during operation
• Replaces stripped, missing, or damaged screws that cause loose assemblies
• Helps maintain electrical and mechanical connections by holding parts in place

• Disconnect power and water before servicing the appliance
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; avoid overtightening which can strip threads or crack plastic
• Keep removed hardware organized for reassembly; replace any additional damaged fasteners

This customized screw is the manufacturer-specified fastener used to secure appliance components and panels at their mounting points. Replace a missing, stripped, or corroded original to restore a tight fit, proper alignment, and help eliminate vibration or rattling.

• Secures brackets, covers, and panels to the chassis at designated mounting points
• Maintains alignment and stability of the assembly during operation
• Helps address loose or rattling components caused by a missing or damaged fastener
• Direct replacement for the original fastener used in the specified location

• Disconnect power; shut off water before servicing
• Match head/length to the original; transfer any original clips or washers if used
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Tighten until snug—do not overtighten into plastic or thin sheet metal

This replacement mounting screw secures appliance panels and components to restore proper fit and reduce rattling or loose parts. Simple, direct replacement when a worn or missing screw causes loose panels or intermittent contact. What it does:

• Fastens panels, brackets, or small components to maintain proper alignment and reduce vibration
• Prevents loose trim, covers, or assemblies that can cause noise or improper sealing
• Replaces missing, stripped, or corroded screws that interfere with reliable operation
• Works wherever the OEM screw specification is required for secure mounting

• Use the matching screw hole and tighten until snug; avoid over-torquing to prevent stripping
• Disconnect power to the appliance if accessing electrical or moving parts near the work area
• If multiple screws are missing or panels are damaged, replace all fasteners for even support

This leveling leg assembly stabilizes and levels your refrigerator so it sits solidly on the floor and the doors align correctly. Replacing a worn or stripped leg helps reduce rocking and vibration and restores smooth leveling adjustment.

• Provides height adjustment to level the cabinet on uneven floors
• Supports the unit to prevent rocking or wobbling
• Helps doors close and seal properly when the cabinet is level
• Symptoms may include persistent wobble, vibration/rattling, or a stripped/bent foot or screw

• Unplug the refrigerator and use a helper to prevent tipping injuries.
• Protect flooring; remove the kickplate/grille for access if present.
• Thread out the worn leg; hand-thread the new assembly and adjust height—do not over-extend.
• Level side-to-side and front-to-back per your owner's manual, then reattach any panels.

This control case assembly is the replacement outer housing that holds and protects the appliance control board and user interface, restoring a secure fit and proper button/panel alignment for safe operation. What it does:

• Houses and protects the control board and associated electronics from dust, moisture, and accidental contact
• Keeps control panel buttons and switches properly aligned for reliable user input
• Prevents loose or rattling control components that can cause intermittent operation or noise
• Supports the front panel and display mounting for normal appearance and functionality

• Disconnect power to the appliance before starting any repair to avoid electric shock.
• Handle the control board and connectors carefully; avoid touching circuit traces or components.
• Basic hand tools are typically required to remove the panel and transfer the control board into the new housing.
• If the control board is damaged or shows corrosion, this part replaces only the housing unless otherwise specified.

Restore usable, level storage space with this Refrigerator Shelf Assembly. It replaces a damaged or missing shelf in the fresh food compartment, helping keep items organized and properly supported so you can make full use of your refrigerator.

• Provides a flat, sturdy surface for storing food and containers
• Replaces shelves that are cracked, shattered, sagging, or missing
• Helps prevent items from tipping and maintains interior organization
• Common signs: broken glass or frame, shelf won't seat in side rails, or slides out

• Remove food from the area and open the door fully
• Lift/tilt the old shelf to release it from the side rails and slide it out
• Align the new shelf with both rail grooves and push in until fully seated
• Handle glass carefully and wear cut-resistant gloves

The Shelf Assembly is an OEM part for LG refrigerators. This shelf assembly provides sturdy and reliable storage space within the refrigerator, allowing for the organization of food items and maximizing the use of the available space.

Causes of a bad shelf assembly can include regular wear and tear, overloading the shelf with heavy items, or accidental impacts that can cause cracks or breaks. A compromised shelf can reduce the overall storage efficiency and safety of the refrigerator.

Symptoms of a bad shelf assembly include:

• Cracks or breaks in the shelf material
• Difficulty in sliding or positioning the shelf
• The shelf not staying securely in place
• Visible warping or instability

This OEM LG part is also compatible with Sears/Kenmore models.

This freezer shelf assembly replaces a damaged or missing shelf to restore usable storage space and stable support for frozen items. It fits into freezer compartment shelving tracks and provides a flat, secure surface. What it does

• Replaces a broken, cracked or warped freezer shelf so food and containers sit level and stable
• Restores organized storage when an existing shelf is bent or missing
• Helps prevent items from tipping or spilling inside the freezer
• Matches OEM fit and mounting points for straightforward shelf support

• One freezer shelf assembly

• Remove food and unplug or switch off the appliance power before starting work
• Shelf typically slides or snaps into place on existing shelf supports; no special tools usually required
• Handle shelf carefully to avoid sharp edges on broken plastic or glass
• If mounting clips or supports are damaged, replace them before installing the new shelf

This small control knob mounts on the shutter mechanism so you can open, close, or fine-tune the setting with a simple turn. Replace a cracked, loose, or missing knob to restore smooth adjustment and a clean, finished look.

• Attaches to the shutter/damper shaft to select positions
• Provides a secure grip for easy, precise adjustment
• Common failure signs: cracked or stripped hub, loose fit, missing knob
• May cause difficulty adjusting the shutter or settings to slip

• Disconnect power if removing any covers or panels near electrical components
• Pull the old knob straight off; rock gently if stuck to avoid damaging the shaft
• Align the keyed/D-flat opening with the shaft and press firmly until fully seated
• The shutter moves smoothly through its full range

This shutter knob attaches to the crisper cover's humidity vent (shutter) and lets you open or close the airflow for produce storage. Replace a cracked or missing knob to restore smooth, precise adjustment of the drawer's vent. What it does:

• Connects to the shutter lever to adjust the vent position on the drawer cover
• Restores the ability to regulate airflow and moisture in the crisper
• Helps ensure the vent moves and stays in the selected setting
• Symptoms may include a broken or missing knob, a vent stuck in one position, or inability to adjust humidity

• 1 shutter knob

• Unplug the refrigerator before servicing; remove the crisper/drawer cover for access if needed
• Pull the old knob straight off the shutter shaft; align flats/tabs and press the new knob on until fully seated
• Do not force the knob—inspect the shutter lever for damage if it won't engage
• Verify smooth vent movement, then reassemble the cover and drawers

This vegetable tray stores and organizes produce in the refrigerator's fresh-food compartment. Replacing a cracked or missing bin restores usable space and smooth sliding access so fruits and vegetables stay contained and easy to reach.

• Holds fruits and vegetables in the crisper area
• Slides in/out on existing drawer rails for convenient access
• Helps keep items separated and contain minor spills
• Common symptoms: cracked or broken bin, missing tabs, drawer won't slide smoothly or stay seated

• Remove contents and slide the old drawer straight out
• Align the new drawer with the existing rails and push in until fully seated
• Handle nearby glass shelves carefully to prevent chips or breakage
• Disconnect power before working inside

Replace a cracked or missing cover with this cover assembly for the TV-designated section of your unit. It restores a clean, finished surface while helping protect internal components from dust, debris, and accidental contact.

• Shields internal components and wiring from dust and accidental contact
• Restores a clean, finished appearance in the covered area
• Helps retain adjacent parts that rely on the cover for proper positioning
• Common symptoms: broken or missing cover, loose/broken tabs, rattling/vibration, exposed components

• Disconnect power to the unit before servicing
• Remove any retaining screws or clips and keep them for reassembly
• Align tabs and mounting holes, seat the cover, and reinstall fasteners
• Do not overtighten screws to avoid cracking plastic; verify the cover sits flush

This cover support bracket secures an appliance cover or panel, restoring proper alignment and stability. Replacing a damaged support helps eliminate rattles and gaps so the cover seats correctly and stays in place.

• Provides structural support for the associated cover/panel
• Keeps the cover aligned and firmly seated against the cabinet
• Replaces a cracked, stripped, or missing support
• Symptoms include a loose or sagging cover, vibration/rattling noises, or covers that won't stay attached

• Disconnect power before servicing; allow any hot surfaces to cool and wear cut-resistant gloves
• Remove the cover/panel to access the support and retain all mounting hardware
• Install the new support, transferring screws or clips as needed
• Reinstall the cover and verify proper fit before restoring power

This replacement shelf glass restores a flat, sturdy surface inside your refrigerator for safe, organized food storage. Replace cracked, missing, or unstable glass to help contain spills and return your shelf to full strength.

• Provides a level, load-bearing surface for food containers in the compartment
• Helps contain leaks and spills so messes don't spread below
• Replace when glass is cracked, chipped, shattered, bowed, or missing
• Restores lost storage space and improves shelf stability

• If handling broken glass, unplug the refrigerator and wear cut-resistant gloves and eye protection.
• Remove items from the shelf, slide out the shelf/assembly, and carefully lift out the old glass.
• Clean any debris from the frame or supports. Set the new glass in place, ensuring it seats fully and is secure before reinstalling.

This Door Gasket Assembly creates a tight seal between the door and cabinet to keep cold air in and moisture out. Replace a worn or deformed gasket to restore proper sealing and help prevent frost and temperature swings.

• Forms the perimeter seal when the door closes to limit warm air infiltration
• Helps reduce frost, ice, and condensation around the door opening
• Supports stable internal temperatures for consistent cooling
• Common symptoms: torn or brittle gasket, visible gaps, door not closing flush, moisture or frost along the door edge

What's included: 1 door gasket Install notes:

• Disconnect power before beginning any repair
• Let the new gasket sit flat to relax, or gently warm it with a hair dryer on low to remove kinks
• Pull the old gasket from the retaining channel; press the new gasket fully into the groove, starting at the corners
• Close the door and check for uniform contact all around; warm and reshape as needed to improve the seal

This door basket snaps onto the inner door to hold jars, bottles, and condiments. Replacing a cracked or missing bin restores secure, organized storage and helps prevent items from tipping or falling when the door opens.

• Mounts on the refrigerator door to provide extra shelf storage
• Helps keep bottles and condiments upright and accessible
• Replaces bins with cracked plastic or broken locking tabs
• Fixes issues where the bin won't stay seated or falls off the door

What's included: 1 door basket Install notes:

• Remove contents and lift the old bin straight up to release from the door liner
• Align the new bin's rear hooks with the slots and press down until fully seated
• Verify placement with your model's parts diagram, as some positions use specific bins
• Let cold plastic warm to room temperature and avoid forcing to prevent cracks

This refrigerator guide aligns and supports a mating component so it travels smoothly and stays on track. Replacing a cracked or missing guide restores proper movement and helps prevent binding, jamming, or premature wear.

• Guides and stabilizes the movement of the associated part to ensure smooth travel
• Keeps components aligned to prevent rubbing, derailment, or gaps
• Common signs of failure: sticking or binding, wobbling/misalignment, or parts coming off track
• Visible damage such as cracks, broken tabs, or missing pieces on the guide

• Disconnect power; if working near a dispenser or water path, turn off the water supply
• Remove the access panel/bin as needed and retain any screws/clips
• Seat the new guide and reuse existing hardware; verify a secure fit
• Restore power and test the component's movement for smooth operation

The Door Stopper is an OEM part for LG refrigerators. It is a component located at the top of the refrigerator door frame. The stopper functions to securely cushion the door in the open position, preventing damage from accidental closing. 

Causes of a faulty stopper include wear from the door repeatedly contacting the part during normal use. Forceful door incidents could also bend or loosen the stopper over time.

Symptoms of a problematic door stopper are:

• The door not staying firmly in the open position
• Increased noise or vibration from the door while open
• Potential damage from an unrestrained door closing

This OEM LG part is also compatible with some Kenmore models.

This name plate is the exterior emblem that mounts to the appliance's front panel. It replaces a missing, cracked, or faded badge to restore a clean, factory look and cover the designated trim area.

• Attaches to the outer panel to display brand/series identification
• Restores a finished appearance where the original emblem sits
• Direct replacement for a lost, damaged, or worn badge
• Typical symptoms: missing emblem, loose or broken tabs, peeling, or discoloration

• Disconnect power before servicing the appliance
• Carefully remove the old emblem; release any tabs from behind or peel away remaining adhesive
• Clean and dry the mounting surface; remove all residue for best fit
• Align with the recess/holes and press evenly until fully seated

This door gasket assembly seals the refrigerator door to the cabinet to stop air and moisture leaks. A tight, even seal helps maintain interior temperature, reduce frost and condensation, and support efficient, reliable cooling performance.

• Creates a continuous perimeter seal between the door and cabinet
• Helps stabilize interior temperature and humidity
• Reduces frost, sweating, and condensation around the door opening
• Replaces gaskets that are torn, warped, brittle, or permanently flattened

• Disconnect power before servicing and clear items from the door.
• Let the new gasket warm to room temperature; relax bends with warm water or low heat if needed. Do not overheat.
• Press the gasket lip fully into the door channel, working evenly around all sides and corners.
• Close the door and verify uniform contact all around; reseat the gasket as needed for an even seal.

This inner door shelf replaces a cracked or broken refrigerator door basket so you can safely store bottles and small items. It restores secure storage and keeps the door organized without rattling or falling items. What it does

• Replaces a damaged or cracked door basket that no longer holds items securely
• Restores proper storage on the refrigerator door and prevents items from slipping or falling
• Reinstates mounting stability if original shelf tabs were broken or worn
• Reduces rattling and improves overall organization inside the door

• Unplug the appliance or disconnect power before starting any repair
• Empty the door compartment and remove any remaining clips or fasteners from the old basket
• Align the replacement basket with the door mounting points and snap or slide into place until securely seated
• If mounting tabs are broken, inspect adjacent hardware and replace any additional damaged clips before use

The Door Basket is an OEM accessory specifically designed for LG refrigerator doors containing vegetable drawers. This hanging basket provides auxiliary storage directly above crisper bins.

Causes of a bad door basket can include wear and tear over time compromising the mesh material, or damage from overloading reducing structural integrity.  

Symptoms of a bad door basket include:

• Holes or tears reducing usable capacity   
• Detached fasteners slipping off mounting brackets
• Warped contours no longer remain properly installed
• Insecure attachment inhibiting safe door openings  

Replace yours today with this genuine OEM LG basket to maximize organizational convenience. Sturdy brackets produce a snug, stable fit. Compatible with Samsung, GE, and Frigidaire refrigerators featuring dual-drawer doors, this upgrade complements any modern kitchen setup. Reliable performance preserves aesthetic appeal.

The Door Basket Assembly is an OEM component for LG refrigerators. It is located within the fresh food doors that securely hold bottles and containers of varying sizes.

Symptoms of a bad door basket assembly include:

• Items failing to remain securely placed or tipping easily within
• Warping or sagging basket components allowing gap openings
• Loose basket fittings inhibiting proper installation or removal
• Sections detaching or coming apart at seams over time

Causes can be normal wear and tear stresses from years of door openings/closings or impact damage.

This OEM LG part can also be used on Kenmore/Sears appliances. 

Upper hinge assembly that restores proper door pivot and alignment for smooth opening and closing. Replacing a worn or damaged upper hinge helps reduce sag, noise, and uneven sealing so the door closes correctly. What it does:

• Supports and pivots the refrigerator door for stable, controlled movement.
• Keeps the door aligned so the gasket seals evenly and the interior stays cold.
• Use when the door sags, binds, grinds, squeaks, or does not latch evenly.
• Replace bent, worn, or damaged hinge components that cause misalignment.

• Disconnect power and remove items from the door before starting; follow all safety precautions.
• Door removal and reinstallation often require a second person to support the door.
• Hinge orientation and hardware before tightening; follow the manufacturer service instructions for final alignment.
• Reuse or replace mounting screws and bushings as needed; do not overtighten fasteners.

Restore smooth, proper door movement with this Center Hinge Assembly. It supports the refrigerator door at the middle pivot point, helping maintain alignment and ensuring the door opens and closes correctly to seal out warm air.

• Supports the door at the center pivot for stable operation
• Helps correct issues like a sagging, misaligned, or rubbing door
• Can reduce squeaks or binding when opening/closing
• Helps the door seal contact the cabinet evenly for proper cooling

• Disconnect power and clear items from the door before service
• Support the door to prevent drops; remove hinge cover and mounting screws
• Transfer any shims/spacers in the original order for proper alignment
• After reassembly, verify door alignment and gasket seal

The Lower Hinge Assembly is an OEM part for LG refrigerators. This lower hinge safely and smoothly supports the weight of the refrigerator door.

Causes of a bad lower hinge can include loose or worn parts from years of use, damage from overloading doors with heavy items, or failure due to impact or bending stresses.  

Symptoms of a bad lower hinge include:

• Doors sagging or dropping over time
• Noisy squeaks or grinding sounds coming from hinges
• Difficulty opening and closing doors smoothly  
• Doors unable to stay open at various angles

Replace yours today with this genuine OEM LG assembly before further issues develop. This replacement part is compatible with Frigidaire, Samsung, and Kenmore models for a factory fit and function.

The Hinge Bushing is an OEM part for LG refrigerators. It serves as a crucial component in the door hinge mechanism, ensuring smooth and stable operation when opening and closing the refrigerator door.

You should replace this hinge bushing if it becomes worn out or damaged. Common causes of a bad hinge bushing include constant use leading to wear and tear, misalignment of the door, or physical damage due to impact.

Symptoms of a bad hinge bushing include:

• Difficulty in opening or closing the door
• The door sagging or not aligning properly
• Unusual noises like squeaking or grinding when the door is moved

This OEM LG part is also compatible with Sears/Kenmore.

This drum support roller helps the dryer drum rotate smoothly and quietly by supporting the drum shaft and reducing friction. Replacing a worn roller restores proper drum movement and reduces noise. What it does:

• Supports the dryer drum shaft so the drum turns evenly during operation
• Prevents metal-on-metal contact that causes squealing, grinding or scraping noises
• Helps maintain correct drum alignment to avoid rubbing or uneven wear
• Works with the dryer's axle and bearing system to enable smooth rotation

• One roller

• Disconnect power and move the dryer to a safe, well-lit work area before starting
• Access requires removing the dryer front or rear panel depending on model
• Inspect the drum shaft, bearing, and idler components and replace any worn parts at the same time
• Wear eye protection and gloves; test the dryer empty after installation to confirm quiet, smooth operation

A small retaining pin used to secure moving parts and keep components aligned for smooth operation. Replacing a worn or broken common pin can stop rattling and restore proper fit between linked parts. What it does:

• Holds or aligns two parts together so they move correctly and stay in position
• Helps prevent rattling, looseness, or parts slipping out of place
• Works as a simple mechanical fastener—no electronics involved

• One common pin

• Disconnect power to the appliance before beginning any service
• Keep track of small parts; lay out components in order to aid reassembly
• May require removal of trim or a hinge/retainer to access the pin—use basic hand tools
• If the pin is difficult to seat, do not force; inspect mating parts for damage

This overload protector is a motor thermal cut-off that helps prevent motor overheating by interrupting power when temperatures get too high. It restores normal operation after the motor cools, helping protect the motor from heat damage. What it does:

• Senses excess motor temperature and interrupts power to prevent overheating
• Commonly used when a washer or motor hums, won't spin, or stops mid-cycle
• Protects the motor and associated components from heat-related failure
• Resets or is replaced after a thermal fault clears, depending on design

• Disconnect power before accessing the motor or electrical components
• Handle and mount the protector per OEM orientation to ensure proper thermal contact
• Inspect motor and wiring for underlying faults before replacing

This small stopper installs in the refrigerator to limit the travel of a moving component and keep it securely in place. Replacing a broken or missing stopper prevents over-extension and helps maintain smooth, aligned operation.

• Limits the range of motion for a door, bin, or drawer to prevent over-opening or accidental removal
• Helps keep interior components aligned and operating smoothly
• Replace if cracked, missing, or deformed
• Common symptoms: drawer or bin slides out too far, door swings past normal range, or a broken plastic stop is found

• Disconnect power before servicing; remove or support the affected bin/drawer/door
• Note the old stopper's orientation and location before removal
• Transfer and reuse any original screws or clips if applicable
• Snap or fasten the new stopper in place and test for smooth movement

This restrainer is a small retaining clip that helps secure moving or removable components in place, reducing rattles and keeping parts aligned for reliable operation. It's a simple replacement for worn or broken clips. What it does:

• Holds a cover, panel, or door-related component in proper position to prevent shifting
• Reduces noise caused by loose or vibrating parts
• Restores original fit where a broken or missing clip allows movement
• Simple mechanical function — no electrical connections or calibration

• One restrainer

• Disconnect power (and water if applicable) before beginning repairs
• Inspect surrounding mounting points for damage; replace any broken tabs or fasteners
• Typically installs with basic hand tools; align clip and press or snap into place until secure

The Drier Assembly is an OEM part for LG refrigerators. This part is responsible for removing moisture and contaminants from the refrigerant. This ensures that the refrigerant circulates effectively and efficiently, preventing damage to other components and maintaining the refrigerator's cooling performance.

Causes of a bad Drier Assembly can include contamination from moisture entering the refrigerant lines, blockages from debris or particulates, and general wear and tear over time that reduces its effectiveness.

Symptoms of a bad Drier Assembly include:

• Reduced cooling efficiency or warm refrigerator temperatures
• Unusual noises from the refrigeration system
• The compressor running continuously or cycling frequently
• Frost buildup on the evaporator coils due to improper refrigerant flow

This OEM LG part is also compatible with Sears/Kenmore models.

This holder is a small mounting bracket used to secure internal components in place, helping keep parts aligned and stable for reliable operation. It provides a direct, OEM-compatible replacement to restore proper fit and function. What it does

• Secures and supports nearby components to prevent shifting or vibration.
• Restores proper alignment where a worn or broken holder causes rattling or loose parts.
• Helps maintain normal operation by keeping assemblies seated correctly.
• Works behind panels or inside assemblies where a dedicated bracket is required.

• One holder/mounting bracket as shown.

• Installation generally requires removing the panel or access cover where the holder is located.
• Use proper fasteners shown in your appliance; replace any damaged screws or clips as needed.
• Disconnect power before servicing electrical appliances to reduce shock risk.

This guide assembly directs and stabilizes the refrigerator/freezer fan to ensure consistent airflow across the evaporator and cooling components. Replacing a damaged guide restores proper air circulation and helps reduce noise from an unsteady fan. What it does

• Holds and centers the fan blade to maintain efficient airflow through the evaporator coil
• Prevents fan wobble or contact with housing that can cause noise or mechanical wear
• Helps ensure even cooling and can reduce frost build-up caused by disrupted airflow
• Supports proper airflow that contributes to consistent temperatures in the cooling compartment

• One guide assembly

• Disconnect power before beginning any repair and follow the appliance manufacturer's safety instructions
• Access may require removing interior panels or the evaporator/fan housing; retain fasteners for reassembly
• Inspect adjacent components while replacing the guide to ensure full repair
• Use only compatible parts and avoid forcing plastic tabs; if clips or screws are damaged, replace them

This motor bracket is the OEM-style mounting bracket that secures the appliance motor to the cabinet, keeping the motor aligned and reducing vibration for reliable operation. It helps restore proper motor support and stable running. What it does:

• Provides a secure mounting point to hold the motor in correct position
• Maintains motor alignment to prevent belt slip and uneven wear
• Reduces vibration and noise caused by a loose or damaged motor mount
• Can resolve symptoms such as unusual motor noise, excessive vibration, or motor movement during operation

• Disconnect power (and gas if applicable) before starting any repair
• Basic hand tools are typically required; follow the appliance service manual for access steps
• Inspect surrounding components (mounting fasteners, motor and belts) and replace any damaged parts

This fan assembly circulates air through the appliance so coils and internal components operate at the proper temperature. Replacing a failed or noisy fan can restore airflow and help prevent performance issues caused by weak circulation.

• Moves air across coils and components to support designed cooling/dehumidifying performance
• Helps maintain steady airflow to reduce overheating or icing conditions
• A failing fan can cause little to no airflow even when the unit is running
• Common symptoms: fan not spinning, intermittent operation, loud rattling/grinding, vibration, or thermal shutdown

• Disconnect power before servicing to avoid electrical shock or injury
• Access the fan area per your unit's service information; remove panels/shrouds as needed
• Note wire connections and mounting order; transfer any brackets, grommets, or hardware from the old assembly
• After installation, ensure the fan spins freely and clears all shrouds, then test operation before reassembly

This replacement fan blade mounts on the fan motor to move air for proper cooling. A cracked, loose, or damaged blade can cause noise and weak airflow—replacing it restores smooth, reliable air circulation. What it does:

• Drives airflow to help maintain stable temperatures throughout the appliance
• Supports efficient cooling by circulating air across key areas
• Common symptoms include rattling or scraping near the fan, vibration, or wobbling
• Replacement is recommended if the motor runs but the blade slips, doesn't spin, or is visibly damaged

• 1 fan blade

• Disconnect power before servicing
• Access the fan area by removing covers/shelves as needed
• Note blade orientation; pull the old blade straight off the shaft and press the new blade on until fully seated
• Spin the blade by hand to confirm clearances, reassemble, and restore power

This controller assembly is the display/control circuit board used in compatible units. Replacing a failed board restores proper front-panel operation so you can select settings, view status, and run the appliance reliably again.

• Governs user input and display functions for the appliance's front panel
• Resolves issues like unresponsive buttons, blank or erratic display, or incorrect function selection
• Helps restore normal operation when the original board is shorted or damaged
• Designed to fit per manufacturer specifications for the intended models

• Disconnect power before servicing; electronic components can store charge
• Handle the board by edges; avoid static discharge—use ESD protection if available
• Photograph wire and connector positions before removal to ensure proper reconnection
• Do not overtighten mounting screws; verify all harnesses are fully seated

This DC fan motor drives the refrigerator's fan to circulate air across the coils and through the cabinet. Replacing a weak or failed motor restores proper airflow for consistent temperatures and reliable cooling performance.

• Spins the fan blade to move air through the cabinet and across heat-exchange coils
• Helps maintain even, stable temperatures throughout the appliance
• Typical failure symptoms: fan not running or intermittent, unusual humming/squealing/rattling near the fan area, poor cooling or temperature fluctuations
• Can reduce hot spots by restoring proper air circulation

• Disconnect power before servicing; use cut-resistant gloves
• Access the motor behind the rear cover or interior panel (location varies by model)
• Note connector orientation; disconnect harness, mount the new motor, and securely route wiring
• Ensure the blade spins freely with no obstructions; restore power and verify fan operation

This motor support damper sits between the refrigerator's compressor and base to absorb vibration and movement. Replacing a worn damper helps quiet rattles and humming from the back of the cabinet and keeps the compressor properly supported.

• Cushions the compressor to reduce transmitted vibration and noise
• Helps quiet humming, buzzing, or rattling from the lower rear of the refrigerator
• Maintains proper compressor alignment and support on the base pan
• Common signs of wear: increased vibration/noise, a cracked or flattened damper, or noticeable compressor movement when running

• Unplug the refrigerator and pull it forward to access the rear; allow the compressor to cool before working
• Support the compressor to remove load from the mount before loosening hardware
• Replace the damper and tighten mounting hardware evenly without over-compressing the rubber
• Avoid bending or stressing refrigerant tubing; wear gloves and eye protection

The Rear Evaporator Motor Grommet is an OEM part for LG refrigerators. It's designed to secure and cushion the evaporator motor, ensuring it remains in place and operates quietly. This grommet plays a crucial role in minimizing vibrations and noise from the motor, which can otherwise lead to a disruptive refrigerator operation.

Causes of a bad Rear Evaporator Motor Grommet can result from deterioration due to cooling and thawing cycles in the refrigerator. Physical damage during cleaning or servicing may cause a loose motor fit.  

Symptoms of a malfunctioning Rear Evaporator Motor Grommet include:

• Unusual noises or vibrations from the back of the refrigerator.
• The evaporator motor shifting out of place, which can affect cooling efficiency.
• Increased wear on the evaporator motor due to lack of proper cushioning and support.

This OEM LG part is also compatible with some Kenmore models.

The Rear Evaporator Motor Grommet is an OEM part for LG refrigerators. It's designed to secure and cushion the evaporator motor, ensuring it remains in place and operates quietly. This grommet plays a crucial role in minimizing vibrations and noise from the motor, which can otherwise lead to a disruptive refrigerator operation.

Causes of a bad Rear Evaporator Motor Grommet can result from deterioration due to cooling and thawing cycles in the refrigerator. Physical damage during cleaning or servicing may cause a loose motor fit.  

Symptoms of a malfunctioning Rear Evaporator Motor Grommet include:

• Unusual noises or vibrations from the back of the refrigerator.
• The evaporator motor shifting out of place, which can affect cooling efficiency.
• Increased wear on the evaporator motor due to lack of proper cushioning and support.

This OEM LG part is also compatible with some Kenmore models.

The Front Evaporator Motor Grommet is an OEM part for LG refrigerators. This grommet cushions and secures the evaporator motor, reducing vibrations and noise during operation to ensure efficient cooling.

Causes of a bad grommet can include prolonged use leading to material fatigue, exposure to extreme temperatures, or physical damage from accidental impacts. A damaged grommet can result in increased noise and potential misalignment of the evaporator motor.

Symptoms of a bad evaporator motor grommet include:

• Increased noise from the refrigerator
• Vibrations or rattling sounds
• Poor cooling performance
• The evaporator motor becoming loose

This OEM LG part is also compatible with Sears/Kenmore.

The Refrigerator Door Switch is an OEM part for LG refrigerators, designed to signal the control system when the door is open or closed. This small but essential component plays a critical role in the overall operation of your refrigerator, including the activation of interior lights and the control of cooling functions. 

Over time, the door switch can fail due to mechanical wear, accidental damage, or a buildup of debris that may prevent it from functioning correctly. 

Symptoms of a bad Refrigerator Door Switch include:

• Interior lights not turning on or off appropriately with the door's position
• The refrigerator running longer than necessary, potentially leading to increased energy bills
• Unusual fluctuations in temperature inside the fridge, affecting food preservation

This OEM LG part can also be used on Kenmore/Sears appliances. 

This harness assembly routes power and signals between appliance components to restore electrical connections and normal operation. It replaces damaged or frayed wiring to stop intermittent power, control failures, or no-start conditions. What it does:

• Reconnects power and control circuits between major components
• Replaces damaged, burned, or frayed wires and connectors that cause intermittent or lost function
• Restores reliable signal paths to controls, sensors, and motors
• Helps resolve symptoms like sporadic operation, failure to start, or component non-response

• Disconnect power to the appliance before accessing electrical components.
• Match connectors and wire routing to the original harness during installation to avoid pin miswiring.
• Inspect connector pins and mating terminals for damage; replace the harness if pins are bent or corroded.

This sheath heater is the replacement heater housing that surrounds and protects the dryer's heating element, helping deliver consistent, directed heat for efficient drying. It restores proper heater alignment and containment for safe operation. What it does:

• Houses and protects the heating element and terminals from direct contact and damage
• Directs and focuses heat into the drum area for more even drying
• Can prevent shorting or arcing by isolating element wiring and connections
• Commonly used when dryers produce little or no heat, take unusually long to dry, or show visible element damage

• Disconnect power to the appliance before starting any repair — electric shock risk.
• Handle the heating element area carefully; do not bend or nick the element or sheath.
• Follow OEM instructions for mounting orientation and wire routing; replace any damaged clips or fasteners.

This part is an LG refrigerator control board. A refrigerator's control board acts as the central processing and command center for the appliance. All of the functions of the refrigerator will originate from the control board. Essentially, the control board is the main nerve center of the refrigerator. A clicking noise may originate from the refrigerator if the board is damaged. Intermittent cooling and freezing is another way of identifying damage. Noticeable dimming of the numbers on the screen may also be an indicator.To install this part, return to the metal faceplate on the back of the refrigerator. Remove the plate and locate the connecting wire. Plug the control board wire into the refrigerator connecting wire. Insert the control board back into place using the mounting clips that hold it into position. Power the refrigerator back on, and make sure the proper functions have returned. Replace the metal plate and reset the refrigerator back to the desired levels.This part is a genuine OEM product and is sourced directly from the manufacturer. The piece described is made exclusively for LG appliances.

The PCB Assembly, Display is an OEM part for LG refrigerators. It is responsible for controlling the refrigerator's display functions and interface. This board monitors temperature and cycle settings and regulates the input/output of operational data to the control panel. It assists users by displaying temperatures, selections, and error codes.

Causes of a bad display board can include liquid damage, thermal stresses from opening/closing doors over time, and short circuits due to manufacturing defects.

Symptoms of a bad PCB assembly include:

• Faulty or unreadable control panel display
• Buttons not responding properly  
• Random error codes appearing
• Glitches in temperature or function display

This genuine LG replacement ensures dependable control panel performance. It preserves your investment and restores full refrigerator operations. This part is also compatible with Sears/Kenmore models utilizing LG components and controls.

This guide tube is a small routing sleeve that supports and protects a rod, shaft, cable, or line inside your appliance. It keeps the path straight to reduce friction, noise, and premature wear.

• Guides and supports a rod/shaft/cable/tube through the chassis
• Maintains alignment for smooth movement or flow
• Helps prevent chafing, kinks, and vibration-related damage
• Typical failure signs: scraping or rattling noises, binding/misalignment, or visible cracks/deformation

• Disconnect power; turn off water or gas before servicing
• Refer to your model's parts diagram for routing and mounting points
• Reuse original screws/clips unless damaged
• Route exactly like the original; avoid pinches/kinks and verify clearances before restoring power

The Icemaker Assembly is an OEM part for LG refrigerators. This assembly includes the necessary components to produce and harvest ice within the freezer compartment. It ensures a steady supply of ice cubes for your household.

Causes of a bad icemaker assembly can include wear and tear over time, issues with the water supply line, electrical malfunctions, or mechanical failures within the icemaker unit. These problems can lead to the icemaker not producing ice or producing ice irregularly.

Symptoms of a bad icemaker assembly include:

• No ice production
• Ice cubes being smaller or misshapen
• Ice cubes sticking together
• Unusual noises from the icemaker
• Water leaks around the icemaker area

This OEM LG part is also compatible with Sears/Kenmore models.

This holder assembly is a structural mounting piece that supports and secures an internal component in your appliance. Replacing a cracked or worn bracket helps restore proper alignment and keeps parts stable during everyday use.

• Provides a rigid mounting point for the attached component
• Keeps parts aligned to reduce movement and vibration
• Helps prevent rattling or noise from loose mounts
• Common signs of failure: visible cracks/broken tabs, looseness, or parts that won't stay seated

• Disconnect power and, if applicable, turn off the water supply before service
• Note the orientation of the original part to match fitment
• Reuse existing mounting screws or hardware unless the manufacturer specifies otherwise
• Do not overtighten fasteners; the secured component is fully seated and stable

This replacement injection tube routes water through the refrigerator's supply system to the ice maker or dispenser, as designed for your model. Replacing a cracked or kinked tube restores proper flow and helps prevent leaks.

• Channels water from the inlet circuit to its destination component (ice maker or dispenser, per design)
• Helps maintain a sealed path for clean, reliable water delivery
• Common symptoms: water leaking inside/behind the refrigerator
• Dispenser has slow/no flow
• Ice maker not filling or producing small/hollow ice; visible cracks, kinks, or brittle tubing

• Unplug the refrigerator and shut off the household water supply before servicing
• Note the original routing and connector types; transfer any reusable fittings or clamps from the old tube
• Insert the tube fully into existing connectors or onto barbed fittings and secure with the original clips/clamps
• Restore water, check all joints for leaks, then power on and test the dispenser/ice fill

 The Water Valve Assembly is an OEM replacement part for LG refrigerators featuring automatic ice makers. This valve assembly controls water delivery to the mold during the ice-making process.

Causes of a faulty valve can involve mineral buildup clogging water pathways, stripped plastic threading, or electrical issues disrupting solenoid control functions.

Symptoms include:

• Inoperative or slow ice production
• Ice maker not filling or making ice completely
• Water leaking from the line connections or valve area

This part is also compatible with some Sears/Kenmore model refrigerators.

This mechanical mounting band secures a bracket assembly inside the appliance to keep components aligned and reduce vibration. It restores proper bracket positioning so moving parts run quietly and reliably. What it does:

• Holds a bracket or component assembly in place to maintain proper alignment
• Dampens movement and reduces vibration-related noise or rattling
• Prevents excess wear by keeping parts from shifting during operation
• Helps maintain correct clearances to avoid interference or rubbing

• Disconnect power before inspecting or replacing internal parts
• Remove only the fasteners necessary to access the bracket; keep track of hardware
• Secure all fasteners to the manufacturer's torque or snug specification
• Replace the band if bent, cracked, or missing to restore proper fit and function

This holder is a small mounting bracket that secures a mating component in place inside the appliance. Replacing a cracked or missing holder restores a firm, rattle-free fit and proper alignment.

• Provides a stable mount for the designated part
• Prevents shifting and vibration that can cause noise or premature wear
• Common signs of failure: broken tabs, stress cracks, or the attached part sagging or falling out
• When damaged, the connected component may be loose, noisy, or misaligned

• Disconnect power; if working near water tubing, also shut off the water supply
• Note the original orientation and mounting points; take a photo before removal
• Reuse existing fasteners and avoid overtightening to prevent cracking the plastic
• Ensure the attached component is secure and clears any moving parts before restoring power