Parts for Frigidaire TFC13M0AW0: 02 - Chest Freezer Parts

This is a gasket.

Size: Approximate 2.5 inches thick, 33 inches wide and 70 inches long.

This inner lid panel replaces the damaged or worn interior surface of the washer's upper lid, restoring a finished appearance and helping the lid secure properly. Designed to match the OEM lid assembly fit. What it does

• Provides the finished inner surface of the washer lid so the lid closes and seals as intended
• Replaces cracked, broken, or warped inner lid material that can catch clothes or interfere with lid operation
• Stops interior rattles or movement caused by a loose or deteriorated inner panel
• Helps maintain proper alignment between the lid and latch for reliable closing

• One inner lid panel (upper washer lid panel) as pictured

• Disconnect power to the appliance before beginning any repair
• Remove screws or retaining clips from the outer lid to separate the inner panel; keep fasteners for reinstallation
• Handle edges carefully to avoid damaging trim or the new panel; common hand tools required

Quantity of 1 clip.

Note: See kit# 5303922007 and 5304406520.

This rubber compressor mounting grommet cushions and isolates the compressor to reduce vibration and noise that can transfer to the cabinet. It helps maintain stable compressor positioning for quieter, smoother operation. What it does:

• Absorbs compressor vibration to lower noise and rattling
• Dampens movement that can cause abrasion or wear on mounting hardware
• Helps maintain proper alignment of the compressor assembly
• Common symptom: excessive buzzing, vibration, or rattling from the back of the appliance

• Always disconnect power to the appliance before servicing.
• Support the compressor before removing mounts to prevent shifting or damage.
• Inspect surrounding mounts and hardware; replace any worn or damaged pieces.

This part has been discontinued by the manufacturer and is no longer available.

The Compressor Run Capacitor is an OEM replacement part for Frigidaire refrigerators. This electrical component is essential for providing the necessary torque to start and maintain the operation of the compressor motor, which is responsible for cooling the refrigerator.

Symptoms of a failing compressor run capacitor include:

• The refrigerator not running or cooling properly
• The compressor failing to start or running intermittently
• Humming or buzzing noises coming from the compressor area

Causes of needing to replace the compressor run capacitor can include normal wear over time, exposure to high temperatures or electrical surges, or physical damage to the capacitor itself.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore refrigerator models. 

This cold control kit replaces the mechanical temperature control thermostat that regulates your refrigerator or freezer's cooling. Restore proper temperature regulation and consistent cycling when the original control sticks, drifts out of calibration, or fails intermittently.

• Senses compartment temperature with a capillary bulb and opens/closes contacts to maintain the set temperature
• Cycles the cooling system on and off for steady, reliable performance
• Common symptoms: too warm or over-cooling/freezing items, unit won't start unless the dial is moved, runs constantly, erratic temperature swings, unresponsive temperature dial
• Helps correct intermittent cooling caused by worn or pitted thermostat contacts

• Disconnect power before servicing; work in a dry area
• Access the control housing, note wire locations, and transfer wires to the new control one at a time
• Route and secure the sensing bulb/capillary exactly as original; do not kink or sharply bend it
• Set to a mid-range setting after installation and allow up to 24 hours for temperatures to stabilize

Includes service line.

This electrical harness connects appliance control components and power circuits so switches, sensors and modules communicate reliably. Replacing a damaged harness restores consistent power and signal paths for normal operation. What it does:

• Routes and joins multiple wires into a single connector assembly for controls and accessories
• Delivers power and signal connections between control boards, switches, sensors and motors
• Failsafe symptoms: intermittent or no power to affected components, controls not responding, or visible melting/charring at connector points
• Helps prevent shorting and erratic operation when intact and correctly routed

• Always disconnect power at the breaker or unplug the appliance before servicing
• Inspect harness and connectors for visible damage, corrosion or melted insulation; do not reuse a compromised harness
• Route harness along original clips/channels and seat all connectors fully to ensure secure connections
• Basic hand tools required; refer to service manual or schematic for routing and connector locations

This wire harness connects the run capacitor to the appliance's electrical system, providing a reliable path for start/run signals so the compressor and fan can operate correctly. It replaces a damaged or worn connector harness. What it does:

• Routes electrical connections between the run capacitor and control components
• Helps ensure proper start/run performance for compressor and motor circuits
• Prevents intermittent operation caused by corroded or loose wires
• Commonly replaced when wiring is visibly damaged or appliances fail to start reliably

• One run capacitor wire harness

• Always disconnect power before servicing electrical components
• Inspect the capacitor for stored charge and discharge safely before disconnecting harness leads
• Match connector ends and wire routing to original harness; avoid stretching or pinching wires