Parts for Frigidaire FCCG3027AB: Cook Top|Mfccg3027as.Svg Parts

This is the upper range top that forms the cooktop surface and supports burners and controls, restoring a secure, finished surface for safe cooking. It helps protect internal components and keeps burners properly aligned. What it does:

• Provides the finished cooktop surface and mounting area for burners, burner grates and controls.
• Protects the range's inner components from spills, heat and debris.
• Keeps burners and components properly aligned for stable operation.
• Replaces a warped, cracked or damaged top that can cause uneven burner placement or gaps.

• Disconnect power and turn off gas supply before starting any work.
• Handle edges carefully; metal parts can be sharp.
• Some fasteners, brackets or burner components may need to be transferred from the old top; verify all mounting hardware is present.

This replacement cooktop grate restores a stable, level surface for pots and pans on a gas range. It replaces a cracked, warped or damaged grate so cookware sits securely and cooks evenly. What it does:

• Supports cookware directly over the burner for safe, consistent cooking
• Replaces broken, chipped or warped grates that cause pots to wobble
• Helps restore proper burner clearance and even heat distribution
• Fits into the cooktop's grate seating locations without modification

• Turn off all power and gas supply and allow the cooktop to cool completely before handling.
• Lift out the old grate and set the new grate into the matching seating locations; no tools typically required.
• Handle with care—grates can be heavy and may have rough edges; wear gloves if needed.
• Do not modify the part; if the grate does not seat properly.

Replacement snap-on cap that restores a finished appearance and helps protect underlying components from dirt and accidental contact. Fits original mounting locations to cover exposed hardware and improve appliance safety and aesthetics. What it does:

• Covers and protects exposed hardware, terminals or posts to reduce debris buildup and accidental contact.
• Restores a clean, finished look to panels, trim or appliance edges.
• Helps reduce rattling or vibration noise caused by missing trim pieces.
• Use when the original cap is cracked, broken, missing or when exposed fasteners are visible.

• Always disconnect power (and water, if applicable) before attempting any repair.
• Remove the damaged cap by hand or with a small pry tool; press the replacement cap onto the mounting post until fully seated.
• Avoid excessive force during removal/installation to prevent damage to the mounting post or surrounding trim.
• If mounting posts or clips are damaged, replace those components to ensure a secure fit.

This replacement cap covers and protects its designated opening or fastener on your appliance. It restores a clean, finished look and helps shield internal areas from dust and wear when the original cap is missing or damaged. What it does:

• Covers a specific opening, fastener, or trim end to protect the area
• Helps keep moisture, grease, and debris out of the assembly
• Restores proper fit and finished appearance
• Typical symptoms include a cracked, loose, discolored, or missing cap

• 1 cap

• Disconnect power and, if applicable, shut off gas/water before servicing
• Note the cap's orientation; gently unclip, pry, or unthread the original per model design
• Seat the new cap fully and avoid forcing or overtightening
• The cap is secure and does not interfere with moving parts

This genuine replacement cap restores a clean, finished look and helps protect the underlying fastener or opening on your appliance. Replace a missing or damaged cap to keep components covered and looking factory-fresh.

• Covers and protects an exposed screw, hinge, or opening from dust and debris
• Restores the appliance's finished appearance
• Helps maintain secure retention of the underlying component
• Common signs of failure: missing or broken cap, cap won't stay in place, cosmetic wear, visible exposed fastener/opening

• Disconnect power before servicing; if working near water or gas lines, shut those off as applicable
• Gently pry off the old cap; avoid scratching surrounding surfaces
• Align and press the new cap until it seats/snaps securely

Note: Quantity of two brackets

Replacement mounting screw used to secure panels and small components on compatible appliances. Restores proper fastening to reduce rattling and keep trim, control panels and brackets aligned for safe, quiet operation. What it does:

• Secures panels, trim, brackets and other small appliance components.
• Replaces loose, missing or damaged fasteners that can cause rattling, gaps or panel misalignment.
• Restores mechanical stability for control panels and interior trim pieces.

• Disconnect power to the appliance before servicing any panels or components.
• Use the correct screwdriver and start the screw by hand to avoid cross-threading.
• Tighten securely but do not overtighten; replace if threads are stripped or the screw will not secure the part.