Parts for Maytag JIS1450DP0: 02 - Cooktop Parts

This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.

• Fastens panels, brackets, covers, or internal parts to the chassis or frame
• Helps maintain alignment and support, reducing rattle, vibration, or looseness
• Replaces missing or damaged screws that have backed out, broken, or stripped
• Restores secure mounting after service when original hardware is lost

• Disconnect power; shut off water or gas supplies before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Match length and thread to the original location; do not substitute with longer hardware
• Tighten snugly; do not overtighten into plastic or thin metal

This glass top cooktop assembly replaces a cracked or damaged cooktop surface to restore a smooth cooking area and improve safety and heat distribution. It matches the original OEM fit for compatible Whirlpool cooktops. What it does:

• Provides a flat, heat-resistant cooking surface for electric range elements
• Restores a sealed barrier over burners to prevent spills from reaching internal components
• Reduces risk of cuts or further damage from chips or cracks
• Helps maintain proper cookware contact for even heating

• One glass cooktop top assembly

• Recommended for installation by an experienced DIYer; follow appliance power-disconnect procedures before starting
• Turn the range power off at the breaker and verify the appliance is de-energized
• Handle the glass with care; wear gloves and eye protection to avoid injury from sharp edges
• Reuse or replace mounting clips and gaskets as needed; verify all fasteners are secure before restoring power

This single hotplate is the surface heating element used on compatible electric ranges and cooktops to provide a reliable cooking surface. It replaces a damaged or non-working element so burners heat properly again. What it does:

• Heats cookware on the cooktop for boiling, frying and simmering
• Replaces elements that fail to power on or produce heat
• Restores even heating when an old element heats unevenly or flickers
• Works with the existing burner receptacle and wiring on compatible ranges

• Disconnect power to the appliance at the breaker before servicing
• Allow the cooktop to cool completely and use gloves to avoid cuts
• Handle electrical terminals carefully; verify tight connections during reassembly

A single hotplate replacement that restores even surface cooking and reliable heat transfer for electric ranges. Designed to mount in the cooktop so pans heat properly and cooking performance returns. What it does:

• Heats cookware on the cooktop surface for boiling, frying and simmering
• Replaces a cracked, warped or visibly damaged hotplate element
• Restores consistent heating when a burner no longer warms or heats unevenly
• Works with the existing burner housing and controls when installed correctly

• Disconnect power to the appliance before starting any work
• Allow the cooktop to cool completely and handle the element by insulated edges
• Verify mounting hardware and wiring connections are secure and match the original
• Test the burner at low and medium settings after installation;

This electronic control board replaces the appliance's main console control, restoring cycle selection, display feedback and timed functions for proper operation. It's the central circuit that interprets user inputs and manages electronic commands. What it does:

• Receives commands from the selector pad or touch controls and runs the appliance's electronic functions
• Controls timing, displays, and cycle progression for accurate operation
• Resolves symptoms like blank or unresponsive display, failure to start cycles, or incorrect cycle behavior
• Works with other console components; a faulty board can cause intermittent or erratic operation

• Always disconnect power (unplug or switch off circuit breaker) before starting service
• Handle the board by edges and avoid touching components; protect against static discharge
• Some models require transfer of the user interface, display lens, or mounting brackets from the old board

Screws for range anti tip bracket: WP3801F656-51. Includes 2 screws.

This anchor tip secures the washer agitator to the transmission shaft so the agitator turns with the washer drive. Replaces a worn or damaged anchor tip to restore proper agitator engagement and reduce slipping. What it does:

• Secures the agitator to the drive shaft so the agitator rotates with the motor
• Helps prevent the agitator from slipping or spinning independently
• Commonly used when the agitator feels loose, makes grinding or clicking noises, or stops agitating
• Simple, low-profile part that works behind the agitator cap

• One anchor tip

• Disconnect power and water before starting any repair
• Remove agitator/agitator cap to access and replace the anchor tip per OEM instructions
• Inspect mating surfaces and replace any additional worn components if engagement remains poor

This trim vent replaces a damaged or worn vent grille to restore proper airflow appearance and help direct air where the appliance needs it. It's a direct-replacement exterior trim piece that cleans up the unit's vent opening. What it does:

• Covers and protects the appliance vent opening while providing a finished appearance
• Directs airflow and helps prevent debris from entering the vent area
• Replaces cracked, broken, or faded vent trim that affects appearance or fit
• Helps reduce rattling or loose trim that can occur with damaged vent pieces

• One trim vent (single grille piece)

• Disconnect power to the appliance before beginning any work
• Typically installs with snap-in tabs or a few screws; avoid forcing to prevent breakage
• Inspect surrounding clips or screws and replace if worn for a secure fit

The Control Panel is an OEM part for Whirlpool ranges. As the central interface involved in all cooking functions, this pane houses the various buttons, dials and display responsible for accurately operating the appliance.

Causes of a bad control pane can be attributed to extended exposure to heat and steam over many years of cooking. Spills, splashes and accidental impacts also potentially take their toll on the delicate electronic components.

Symptoms of a bad range control pane include:

• Non-functional or unresponsive control buttons
• Errror codes or fault messages appearing on the digital display
• Physical damage, cracks or breaks in the pane material
• Faulty temperature or time readout that does not calibrate properly

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This mounting bracket secures appliance components to the cabinet or chassis, restoring proper alignment and support. Designed to replace damaged or missing brackets, it helps reduce vibration and prevent parts from shifting during use. What it does

• Provides a stable anchor point for internal components or panels
• Restores proper alignment and fit between the appliance cabinet and mounted parts
• Helps reduce vibration and rattling caused by loose or broken supports
• Commonly replaced when bracket is bent, cracked, or missing

• Inspect adjacent fasteners and mounting holes; replace any stripped screws or damaged hardware
• Use appropriate tools and mounting hardware for secure installation; torque to OEM recommendation if available
• Disconnect power before working on electrical appliances and follow all safety guidelines

This insert is a small OEM component designed to fit into a specific location on your appliance to secure, align, or finish an assembly. Replacing a worn, damaged, or missing insert restores proper fit and clean appearance.

• Provides a snug interface or cover within the designated assembly
• Helps prevent looseness, vibration, or gaps in the connected part
• Replaces cracked, worn, or missing insert pieces
• Common symptoms include loose or wobbly parts, misalignment, or a missing cap/cover

• Disconnect power and shut off gas/water before servicing
• Refer to your model's parts diagram to confirm location and orientation
• Use non-marring tools to avoid cosmetic damage
• Seat the insert fully; do not overtighten adjacent fasteners

The Keypad Wire Harness is an OEM part for Whirlpool ranges. This component is essential for connecting the keypad to the control board, enabling communication between user inputs and the range's operational functions.

Causes of a bad keypad wire harness can include wear and tear from regular use, exposure to heat and moisture, or physical damage due to mishandling or accidental impact. Electrical issues such as short circuits or frayed wires can also lead to malfunctioning.

Symptoms of a bad keypad wire harness include:

• Unresponsive keypad buttons
• Intermittent or inconsistent range operation
• Error codes related to keypad communication
• The range not powering on or off correctly

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.