Richard C Kenner , LA May 03, 2014 Appliance: Maytag 48" Gas Built-In Downdraft Cooktop JGD8348CDP16 Burner corroded on a jenn air 48" gas cooktop Much simpler than expected. You have to remove the cartridge containing the two burners, then dissemble the plate at the bottom to access the burners, It only requires unscrewing approx six screws holding the access cover and 2 screws at the front that hold the ignition "prongs". One you remove the bottom plate you have full access to the burners from the bottom. You then have to unscrew the screws that hold the gas supply tube to the burner and the igniter. from the burner you are replacing. The burner comer right out and you simply replace it with the new burner and reassemble it careful not to over-tighten screws and strip them. Pay attention to the position of the new burner so that it is lined up so that your igniter wire will reach fully back to where the prongs go through the cartridge. When you see it it will be obvious. Reassemble everything and test. Read More... 11 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: Less than 15 minutes Tools: Screwdrivers
Oscar M Woodside , CA May 01, 2015 Appliance: Model JEN AIR Burner had a hole and gas was escaping Easy fix - remove the burner cartridge, remove the cover (about 10 small screws) to get to the burner, twist and turn to remove, then 2 more screws to remove igniter, that's it. You do not need to buy the entire cartridge just buy this part Read More... 10 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: Less than 15 minutes Tools: Screwdrivers
Kevin R Plympton , MA November 18, 2016 Appliance: Maytag 30" Gas Built-In Downdraft Cooktop JGD8130ADB20 One burner the burner was rotted other burner the igniter was not working Lifted out the burner assembly on right side of cooktop which included the two burners that needed repair. Opened up the assembly by removing four screws and that gave me access to underneath the burners. Removed the tube and the igniter from bad burner. Put new burner in place and attached tube and igniter. Took igniter off other burner and put new one on. Put assembly together and put back into place. Read More... 2 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: 30-60 minutes Tools: Screwdrivers
Achl G Scottsboro , AL July 16, 2021 Burner cap rusted. Took burner module out, replaced burner cap. Read More... Do-It-Yourself Rating: Repair Time Estimate: 15-30 minutes Tools: Nut Drivers
Jeremy F Sandy Springs , GA July 03, 2020 Original part rusted out Disassembled the burner and installed the new one. Easy install. Read More... Do-It-Yourself Rating: Repair Time Estimate: Less than 15 minutes Tools: Screwdrivers
Ray E Saltillo , MS December 04, 2017 Burner had rust holes which cause gas leakage. Replaced burner and brass seal. Read More... Do-It-Yourself Rating: Repair Time Estimate: Less than 15 minutes Tools: Screwdrivers
Rickey M Momence , IL December 02, 2017 Appliance: Jenn-Air Range-S/C S/I Gas & Elec Duel Fuel JDS9860AAP Both burners rusted out. Not a problem ! Read More... Do-It-Yourself Rating: Repair Time Estimate: 15-30 minutes Tools: Screwdrivers
Lance M Garnet Valley , PA October 31, 2016 Appliance: Model JDS98860AAP Gas cooktop burner went bad Quick disassembly and reinstall of new part. Not completely effortless due to corrosion under the pan it fit into but was able to get the old burner out and the new one in with a little effort.I got the right part just some rust keeping the old burner from coming out and the new burning from going in quicker. Read More... Do-It-Yourself Rating: Repair Time Estimate: 15-30 minutes Tools: Screwdrivers
Judy M Camden , AR November 15, 2014 Appliance: Maytag 30" Gas Built-In Downdraft Cooktop JGD8130ADS20 Burner burned out I ordered a new part and my husband fixed it. Please enclose new screws because old ones were rusted and needed replacing. Read More... Do-It-Yourself Rating: Repair Time Estimate: 15-30 minutes Tools: Screwdrivers