Parts for Frigidaire FGB24S5DCF: 09 - Door Parts

A replacement 10-24 x 5/8 screw used to fasten interior and exterior appliance components. Simple, direct-fit hardware that restores secure mounting where a worn or missing machine screw is causing loose panels or trim. What it does:

• Secures panels, brackets, and trim pieces to prevent rattling and misalignment
• Replaces stripped, rusted, or lost screws that cause loose or vibrating parts
• Restores proper attachment for components that won't stay in place
• Works wherever a 10-24 x 5/8 machine screw is required

• One 10-24 x 5/8 screw

• Use the correct driver and steady pressure to avoid stripping the head or threads
• Tighten until snug; avoid over-tightening which can damage mating parts
• Disconnect power to the appliance before working on electrical or moving components
• Replace the receiving nut or insert as needed for a secure fit

This inner oven door liner replaces the damaged or worn interior panel that surrounds the oven cavity, restoring the door's sealed inner surface and helping maintain proper cooking conditions and easy cleanup. What it does:

• Forms the inner surface of the oven door and protects insulation and outer door components
• Helps maintain oven heat containment for consistent cooking performance
• Provides a smooth, cleanable interior surface to prevent food buildup
• Restores fit and finish when the original liner is cracked, dented, or warped

• One oven door inner liner

• Requires removal of the oven door and disassembly of the door panels; follow the oven manufacturer's door-removal instructions
• Handle carefully to avoid scratching the finished surface and to protect any attached glass or trim
• Disconnect power to the appliance before beginning work to avoid electrical or heating-element hazards

This drum roller supports the dryer drum and helps it turn smoothly, reducing friction and noise. Replacing a worn roller restores quieter operation and helps prevent drum wobble and uneven tumbling. What it does:

• Supports the rotating drum so it spins freely and evenly.
• Reduces squeaks, grinding noises and excessive vibration from a worn wheel.
• Helps prevent drum wobble that can lead to uneven drying or wear on other components.
• Works with the drum shaft/bearing system to maintain proper drum alignment.

• Disconnect power (and gas, if applicable) before starting any service.
• Remove the dryer drum to access and replace the roller—follow your model's service manual or OEM instructions.
• Inspect adjacent rollers, bearings and the shaft for wear while the drum is removed.

This handle assembly replaces a broken, cracked, or missing refrigerator door handle so the door opens and closes securely and looks finished. Durable molded construction matches the original fit and lever action. What it does:

• Provides the gripping surface and mounting points to open and close the refrigerator door
• Restores proper door control when the original handle is cracked, loose, or detached
• Keeps the door aligned with its latch area for smooth operation
• Prevents hand contact with damaged edges and improves cabinet appearance

• Unplug the appliance or switch off power before beginning work to avoid injury
• Remove any trim or screws holding the old handle; keep fasteners if they are undamaged and listed for reuse
• Align the new handle with the mounting bosses and fasten securely without over-tightening to avoid cracking the plastic
• If the handle uses hidden clips or adhesive trim, verify clip engagement and door operation before finishing

This adhesive seal tape is a replacement sealing strip used to restore a tight seal on appliance doors and panels, helping reduce air leaks and improve temperature control. It's a simple repair for worn or damaged seal edges. What it does:

• Provides a flexible, adhesive sealing surface to close gaps between door/panel and cabinet
• Helps reduce air or moisture leakage that can cause temperature loss or inefficient operation
• Restores worn or deteriorated sealing surfaces without replacing the entire gasket
• Compatible with applications where a narrow adhesive sealing strip is required

• Clean and dry the mounting surface thoroughly before applying for best adhesion
• Measure and trim the tape to fit; press firmly along the full length to ensure contact
• Allow adhesive to set per ambient conditions before closing the door or returning to service

This is a #8 screw, 0.500 inch long, used to secure panels and components in appliances. It provides a correct-fit fastener for repairs where the original #8 x 1/2" screw was required, restoring proper assembly and stability. What it does:

• Fastens trim, panels, brackets and small components where a #8 x 1/2" screw is specified
• Holds parts securely to prevent rattling, gaps or loose panels
• Replaces worn, stripped or missing screws to restore proper fit
• Appropriate for common interior and exterior appliance mounting points

• Use the correct screwdriver (typically Phillips) and avoid over-tightening to prevent strip or damage
• Disconnect power and follow appliance manufacturer safety instructions when accessing internal parts

This is a replacement mounting screw used to secure panels and components in compatible Frigidaire appliances. It restores proper fit and helps prevent rattles, loose panels, and parts that shift during operation. What it does:

• Fastens trim, panels, brackets, or controls to the appliance frame
• Restores secure attachment to reduce vibration, noise, and movement
• Replaces stripped, missing, or corroded screws that prevent proper assembly
• Works wherever the OEM screw with this part number is specified

• Disconnect power to the appliance before beginning any repair
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug—do not overtighten to avoid stripping threads or damaging parts
• Keep removed hardware organized and compare parts to the old screw for correct fit