Parts for Frigidaire FGGF3685TSA: 06 - Door Parts

This insulation assembly replaces the damaged or missing refrigerator cabinet insulation to help maintain proper cooling and reduce energy use. It fits behind liner panels to restore thermal protection and reduce frost and long-run symptoms. What it does

• Restores the insulating barrier behind the cabinet/liner to help the appliance hold temperature more consistently.
• Reduces excessive compressor run time and frequent cycling caused by lost insulation.
• Helps limit frost build-up and uneven cooling when installed correctly.
• Supports overall energy efficiency by replacing compressed, torn, or missing insulation.

• One insulation assembly.

• Disconnect power before beginning; remove food and drawers as needed.
• Access typically requires removing interior liner or panels—retain all screws and retainers.
• Wear gloves and eye protection when handling insulation; avoid inhaling fibers.

This inner oven door glass replaces a cracked, cloudy, or broken oven door panel to restore visibility and maintain a sealed cooking cavity. It fits behind the outer door and provides the transparent barrier you see through while cooking. What it does:

• Replaces damaged inner door glass to restore clear viewing of the oven cavity
• Helps maintain the oven door seal and supports normal heat containment
• Addresses symptoms like visible cracks, chips, or excessive fogging between door panels
• Restores a safe, functional barrier between the oven cavity and the kitchen

• One inner oven door glass panel as specified by the manufacturer

• High-level replacement only: remove oven door and disassemble per manufacturer instructions
• Handle carefully—glass edges can be sharp; wear cut-resistant gloves and eye protection
• Verify correct orientation and any required clips, gaskets, or spacers are present before reassembly

Size: 3/4 inch od x 1/4 inch id.

This is a replacement screw used to secure appliance panels and components. It restores proper fastening so panels, trim, or assemblies stay tight and reduce vibration or rattling. What it does

• Fastens panels, brackets, or trim to the appliance chassis
• Helps stop loose or vibrating panels and trim pieces
• Restores proper alignment where a missing or stripped screw causes gaps or movement
• Use when the original screw is missing, damaged, or corroded

• One replacement screw as shown

• Disconnect power to the appliance before starting any repair
• Use the correct screwdriver or bit to avoid stripping the screw head
• Tighten until snug; avoid over-torquing which can strip threads or crack plastic
• Keep removed screws in a safe place; this screw matches the original before installation

This spacer sets the correct gap between mating parts in your appliance's assembly, preventing rubbing and misalignment. Replace a missing or worn spacer to restore a solid fit, reduce noise, and protect surrounding components.

• Maintains proper spacing between components for correct alignment and operation
• Reduces metal-to-metal contact, squeaks, and premature wear
• Helps fasteners and panels seat securely
• Typical symptoms when failed: loose or rattling parts, uneven gaps, or visible wear marks

• Disconnect power; for gas models, shut off the gas. Allow the appliance to cool completely.
• Access the assembly per your model's diagram; note the original orientation/stack-up before removal.
• Reuse original fasteners if serviceable; hand-start threads and tighten snugly to avoid damaging the spacer.
• Verify alignment and clearances before fully reassembling. Quantity and location vary by model.

This appliance screw fastens panels, brackets, and other components inside the unit. Replace a missing, rusty, or stripped fastener to restore a secure fit and help prevent rattles, misalignment, or premature wear.

• Secures appliance components such as panels, brackets, and covers
• Restores proper fit when an original screw is missing or stripped
• Helps reduce vibration and noise from loose parts
• Common signs: loose or misaligned parts, rattling, or a missing screw

• Disconnect power before servicing
• Match the new screw to the original for size and thread before installing
• Hand-start threads to avoid cross-threading; do not overtighten
• Reuse any original washers or clips if they were used with the old screw