Parts for Kitchenaid KUWL304EBS03: Door Parts

This flat washer is a small hardware fastener used to distribute load and keep screws or bolts secure. It helps maintain tight connections and prevents damage to appliance surfaces where fasteners pass through. What it does:

• Provides a smooth bearing surface for screws or bolts to reduce wear
• Helps distribute load to prevent fastener pull-through or material deformation
• Reduces loosening from vibration that can cause rattling or misalignment
• Commonly used where a secure, flush fastener connection is required

• One flat washer

• Disconnect power and water to the appliance and follow basic electrical and safety precautions before replacing hardware
• Use the washer with the matching screw or bolt size and material specified by the manufacturer
• Inspect mating surfaces and replace any damaged fasteners or parts to ensure a secure fit

This is a replacement door hinge used to secure and pivot a refrigerator door, restoring smooth opening/closing and proper door alignment. It helps stop sagging, misalignment, and uneven sealing to improve cold retention and operation. What it does:

• Provides a durable pivot point so the refrigerator door opens and closes smoothly.
• Restores correct door alignment to improve gasket sealing and reduce cold air loss.
• Stops door sag and prevents catching or scraping when opening/closing.
• Supports the door weight and maintains proper clearance for drawers and shelves.

• Power off and unplug the appliance before starting repair to avoid injury.
• Support the door during removal/installation to prevent dropping or damage.
• Use basic hand tools; torque fasteners to manufacturer specifications when available.
• Examine for additional repair needs.

This gasket forms a reliable seal between mating components to prevent air or water leaks and keep your appliance performing as designed. Replace a brittle, torn, or flattened gasket to restore proper sealing and reduce leaks, condensation, and energy loss.

• Seals the joint between parts to prevent air or water from escaping
• Helps maintain correct temperature, airflow, and moisture control
• Wear signs include cracks, deformation, or permanent compression
• Failure can lead to leaks, condensation/frost, temperature swings, or odors

• Disconnect power before service; shut off water or gas if applicable
• Note the orientation of the original gasket and match the profile during install
• Clean mating surfaces; press the gasket in evenly without twisting or stretching
• After installation, inspect for gaps and test for leaks or air escape

This replacement oven bottom plate protects the oven floor from spills and direct flame contact while helping maintain even heat across the cooking surface. It restores the oven interior to a clean, finished condition. What it does

• Shields the oven floor from spills, drips and food debris to simplify cleanup
• Helps distribute heat more evenly across the oven cavity for consistent cooking
• Prevents direct contact between cookware and heating elements to reduce burn spots
• Replaces a cracked, warped or heavily corroded plate that can affect oven performance

• Disconnect power to the appliance before servicing to avoid electrical shock
• Allow the oven to fully cool before removing or installing the plate
• Use basic hand tools and avoid forcing clips or fasteners to prevent damage

This is an outer panel for a wine cooler. This outer panel is also the functional outer door of the wine cooler. It attaches to the inner liner and glass, assisting to keep the unit cold. The panel is made mostly of glass, so it is see-through, allowing its inner contents to be visible even when the door is closed. This panel is for doors that are hinged on the left.If the outer panel has shattered, cracked or is damaged in any other way, it should be replaced. When replacing the outer panel, first be sure to unplug the wine cooler. As there may be shards of glass or cracked glass, protective gloves will be crucial for safety.The product is made for a KitchenAid wine cooler. It is packaged and sold as a single unit. It is sourced directly from the manufacturer and is an authentic OEM replacement part.

The Drawer Front is an OEM replacement part for Whirlpool appliances. It is designed to cover and protect the front of the drawer, enhancing the overall aesthetics while ensuring easy access to your stored items.  

A bad drawer front can occur due to accidental damage, wear and tear, or discoloration. If you notice symptoms such as cracks, scratches, or an unsightly appearance, it may be time to replace the drawer front.

Symptoms of a bad drawer front include:

• Cracks or damage on the front surface
• Scratches or visible signs of wear
• An unsightly appearance

Repair your beverage center, mini fridge or wine cooler by replacing the faulty or damaged drawer front with this genuine OEM part.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.