Parts for Lg LMV2031ST: Door Parts

This customized nut is a small fastener used to secure components inside an appliance. Replacing a stripped, rusted, or missing nut restores a tight hold, reduces vibration, and helps keep panels and brackets properly aligned.

• Threads onto a matching screw or bolt to clamp parts together
• Maintains alignment of panels, brackets, and internal assemblies
• Helps prevent vibration, looseness, and rattling during operation
• Common failure signs: missing hardware, stripped threads, or components that won't stay tight

• Disconnect power; turn off water or gas before servicing
• Match the thread size/pitch to the original fastener before installation
• Hand-start threads to avoid cross-threading; tighten until snug—do not overtighten
• Replace any worn companion hardware (screw/bolt/washer) as needed

This door frame assembly replaces a damaged or warped outer door frame to restore proper fit and finish. It re-establishes a stable support for the door and helps the appliance close and seal correctly. What it does

• Provides the structural outer frame that supports the door and inner components.
• Restores correct door alignment and reduces gaps that can cause rattling or poor closure.
• Helps prevent debris and moisture from entering the door cavity.
• Useful when the existing frame is cracked, bent, or cosmetically damaged.

• Disconnect power (and water, if applicable) before beginning any repair.
• Handle any glass or trim pieces carefully to avoid breakage or injury.
• Replacement typically requires removing the door from its hinges and detaching exterior trim; keep fasteners organized.

The Choke Cover is an OEM part for LG microwaves. This is a protective shield that covers the microwave’s internal components, preventing interference and ensuring the safe operation of the microwave.  

Causes of a bad choke cover can include physical damage from accidental impacts, deterioration due to prolonged use, or exposure to high temperatures.

Symptoms of a bad choke cover include:

• Unusual noises during microwave operation
• Visible cracks or damage to the cover
• Microwave not heating food properly
• Sparks or arcing inside the microwave

This OEM LG part is also compatible with some Kenmore models.

This is a complete outer door assembly that restores the refrigerator's front appearance and allows the door to open and close securely. It replaces a damaged or dented outer door to refresh function and cosmetic finish. What it does:

• Replaces a bent, dented, or cosmetically damaged outer door to restore appearance
• Provides the structural mounting surface for the handle, trim, and hinge hardware
• Ensures the door closes properly so internal temperature control can function as designed
• Helps prevent drafts and moisture intrusion at the cabinet opening when aligned correctly

• Disconnect power to the appliance before starting any work
• This heavy panel may require two people to safely handle and align
• Remove and retain original fasteners/hinges unless new hardware is explicitly included
• Adjust hinge screws as needed

The Locker is an OEM replacement part for LG microwaves. It is a metal hook located on the side of the microwave door that securely fastens the gasket and seals when closed. The door hook ensures a tight compressive fit of the door gasket all around the perimeter of the door opening. 

Symptoms of a bad door hook include:

• Gaps appearing around the door seal allowing steam or heat to escape  
• The door not sitting flush and securely closed
• Risk of accidental opening during a cooking cycle
• Reduced heating efficiency 

Causes tend to be normal wear over time, like dulling or bending of the thin metal hook. Impact or over-tightening could potentially damage or deform the hook.

This part is also compatible with Sears/Kenmore microwaves.

This replacement door handle restores a secure grip and clean look on your appliance door. If the original handle is cracked, loose, or missing, installing this part lets you open and close the door with confidence.

• Provides the handhold needed to open and close the door
• Attaches to the door using existing mounting points
• Replaces damaged, worn, or missing handle
• Common symptoms: loose or wobbly handle, cracked/broken handle, difficulty opening the door

• Disconnect power to the appliance before servicing
• Protect glass and finishes; support the door while removing/installing the handle
• Note handle orientation and screw locations; transfer and snug existing hardware without overtightening
• Some models require removing inner door trim to access mounting screws—follow your model's service information

This is a complete outer door assembly that restores the refrigerator's front appearance and allows the door to open and close securely. It replaces a damaged or dented outer door to refresh function and cosmetic finish. What it does:

• Replaces a bent, dented, or cosmetically damaged outer door to restore appearance
• Provides the structural mounting surface for the handle, trim, and hinge hardware
• Ensures the door closes properly so internal temperature control can function as designed
• Helps prevent drafts and moisture intrusion at the cabinet opening when aligned correctly

• Disconnect power to the appliance before starting any work
• This heavy panel may require two people to safely handle and align
• Remove and retain original fasteners/hinges unless new hardware is explicitly included
• Adjust hinge screws as needed