Parts for Maytag JDS1450DS1: 05 - Door Parts

This mounting bracket secures and supports appliance panels and internal components to keep assemblies aligned and stable during operation. It restores proper fit and prevents excessive vibration or movement in the affected area. What it does:

• Provides a sturdy attachment point for cabinet panels and internal parts
• Helps maintain correct alignment to reduce rattling and vibration
• Restores secure mounting after damage, wear, or during reassembly
• Commonly used when panels are loose, misaligned, or produce noise

• One mounting bracket

• Turn off and unplug the appliance before beginning any repairs
• Verify bracket orientation and fastener locations match the removed part
• Use the original screws or OEM-recommended fasteners; replace any stripped hardware

This replacement screw secures appliance components and panels. Replacing worn or missing hardware restores a tight, rattle-free fit and helps keep assemblies properly aligned for reliable performance.

• Fastens panels, brackets, or covers to the appliance frame or mating parts
• Helps maintain proper alignment and reduces vibration and noise
• Replaces missing, stripped, or corroded screws
• Common signs to replace: loose or rattling panels, misaligned parts, damaged screw head or threads

• Disconnect power; also shut off water or gas to the appliance if applicable
• Compare to the original to ensure thread and length match before installing
• Start threads by hand to avoid cross-threading; tighten only until snug
• If the mating clip/insert is stripped, replace that hardware as well

This door liner is the oven's inner door panel that helps protect the door cavity and support the inner glass. Replaces a damaged or worn liner to restore a clean interior surface and proper glass fit. What it does:

• Replaces the oven's inner door panel that secures the inner glass and insulation
• Restores a sealed, smooth interior door surface to help contain heat and cooking messes
• Helps eliminate rattles or misalignment caused by a cracked or bent liner
• Compatible with ovens that specify part number W10902192

• One inner oven door liner

• Refer to the oven model's service manual for step-by-step disassembly and reassembly
• Disconnect power (and gas if applicable) before starting work
• Handle the glass and liner carefully—wear gloves and eye protection to avoid cuts
• If other door components are damaged, inspect and replace them as needed for a complete repair

The Door Glass is an OEM replacement part for Whirlpool ranges. It provides insulation and protection for the oven cavity and maintains the proper temperature inside the oven while allowing you to visually check on your dishes without opening the door.

Symptoms of a faulty inner door glass include:

• Cracks or shattered glass
• Foggy or discolored appearance
• Heat escaping from the oven

A bad inner door glass can occur due to accidental damage, extreme temperatures, or regular wear and tear. If you notice signs such as cracks, shattered glass, or foggy appearance, it may be time to replace the inner door glass.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

This replacement door handle restores a secure grip and proper function to the refrigerator door so it opens and closes smoothly. It matches OEM fit and appearance for direct replacement on compatible units. What it does:

• Replaces a cracked, broken, or loose refrigerator door handle
• Restores secure, comfortable grip for opening and closing the door
• Helps keep the door aligned and sealing properly when latched
• Matches original fit and mounting points for easy swap-out

• Disconnect power to the appliance before beginning any repairs when applicable
• Remove any trim or screws that secure the old handle; keep original fasteners unless new hardware is supplied
• Align handle with mounting holes and tighten fasteners securely but do not overtighten

This screw-and-washer fastener is a factory-size 8-18 x 5/16 hardware piece used to secure appliance panels and components. Replace stripped, rusty, or missing hardware to restore a tight, rattle-free fit and proper alignment. What it does:

• Fastens sheet-metal panels, brackets, and small components in the appliance cabinet
• Replaces lost, stripped, or corroded screws to maintain secure mounting
• Helps reduce vibration, buzzing, or rattling from loose parts
• Useful when the original hardware is missing or no longer holds securely

• Includes 1 screw-and-washer fastener (8-18 x 5/16)

• Disconnect power; shut off gas and water supplies if applicable
• Match the fastener to the original location; sizes can vary by application
• Start threads by hand to avoid cross-threading; use an appropriately sized driver
• Tighten snugly without overtightening to prevent stripping sheet metal

This flat washer is a direct-replacement fastening washer that restores proper spacing and fastening for appliance panels and components. It helps re-secure loose hardware so assemblies sit and operate as intended. What it does:

• Provides a smooth bearing surface for bolts and screws to distribute load
• Helps keep fasteners tight to prevent wobble or loose panels
• Restores correct spacing and alignment between mating parts
• Can reduce vibration-related noise when worn or missing

• One replacement flat washer

• Disconnect power and water before starting repairs
• Use the correct size socket or driver to remove and reinstall fasteners
• Inspect mating fastener and surrounding parts for wear; replace if damaged
• Tighten hardware securely but avoid overtightening which can deform the washer

A replacement door hinge that restores proper door alignment and smooth opening and closing. Replaces worn or damaged hinges to help stop door sagging, binding, or poor sealing for safer, reliable operation. What it does:

• Provides the pivot and support that lets the appliance door open and close smoothly.
• Replaces a worn or broken hinge to correct door sag, binding, or uneven gaps.
• Restores proper door sealing and alignment to improve operation and reduce leaks or drafts.
• Matches the form and function of the original hinge.

• Unplug the appliance or disconnect power before starting any repair.
• Support the door while removing/installing the hinge to prevent dropping; have an assistant if needed.
• Use the appropriate hand tools; reuse original fasteners if replacement hardware is not provided.
• After installation, check alignment and operation; tighten fasteners securely but avoid over-torquing.

This glass bracket secures the oven/microwave door glass, keeping the inner glass panel aligned and stable for safe operation. It replaces worn or damaged brackets to restore proper door fit and reduce rattling. What it does:

• Secures and supports the door's inner glass panel to maintain alignment
• Prevents glass movement that can cause vibration, noise, or improper sealing
• Helps restore proper door closing and even heat retention when functioning parts are present
• Commonly replaced when bracket is cracked, bent, or missing mounting integrity

• One glass bracket

• Disconnect power to the appliance before beginning any repair
• Handle glass carefully; wear cut-resistant gloves and eye protection
• Installation typically requires partial door disassembly and removal of retaining screws—keep track of fasteners

Color: Stainless

This factory fastener secures appliance panels, brackets, and internal components. Replacing a missing, stripped, or corroded screw restores proper fit and stability, helping reduce vibration, rattling, and wear during everyday operation.

• Secures covers, brackets, and assemblies to the cabinet or frame
• Restores alignment to reduce gaps, looseness, and vibration
• Replaces lost, damaged, corroded, or stripped hardware
• Matches the original fastener for correct fit and retention

• Disconnect power and shut off water or gas before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Tighten snugly—do not overtighten to prevent thread or plastic damage
• Inspect receiving threads or clips; repair/replace if stripped or broken