Parts for Maytag MGDB765FW0: 04 - Door Parts

The Inner Door Panel is an OEM part designed specifically for Whirlpool electric dryers. Located on the interior dryer door, it protects critical wiring and components from impacts or damage during normal laundry loads.

Causes are usually general wear and tear from contact with wet clothes during loading and unloading cycles. Impact damage during maintenance is also possible.

Symptoms of a bad inner door panel include:

• Appearance has diminished severely from repeated use
• Exposed edges or surfaces could potentially pinch fingers  
• Portions no longer stay securely attached to the door
• Wiring or other internal pieces now lack safeguarding

This OEM Whirlpool replacement panel maintains critical Door protection. Installed promptly, it safeguards dryer internals to boost longevity.

Compatible also with some GE and Crosley dryer models, this part restores trusty function. Protect your valuable dryer with an OEM inner door panel replacement when needed.

This retainer clip secures small appliance components in place to prevent movement and ensure proper alignment for reliable operation. It's a simple replacement that restores lost or broken mounting support. What it does:

• Holds and stabilizes the attached component or assembly to prevent shifting during use
• Maintains proper alignment for connected parts to reduce wear and noise
• Commonly used where a small plastic or metal clip is needed for secure mounting
• Can address symptoms like loose panels, rattling, or parts that won't stay seated

• One retainer clip

• Disconnect power to the appliance before attempting any repair
• Remove surrounding panels as needed to access the clip; small trim tools may help
• Replace the broken retainer with the new clip and verify the secured component is seated correctly

This replacement seal restores a tight barrier at its mounting point in your appliance. It helps prevent leaks and maintains performance by ensuring a proper fit between connected components where fluids or air must be contained. Location varies by model.

• Creates a reliable seal between mating parts to contain water or air
• Helps stop drips, seepage, and unwanted airflow that can affect performance
• Replace if cracked, flattened, swollen, or leaking
• Common symptoms: moisture under/around unit, residue, or diminished efficiency
• Direct-fit replacement to match the original part's size and profile

• Disconnect power and, if applicable, shut off water supply before servicing
• Note the original seal's orientation; clean and dry all sealing surfaces
• Lightly moisten or use only manufacturer-approved lubricant; avoid petroleum products unless directed
• Seat evenly without twisting; after reassembly, run a test cycle and check for leaks

This outer door assembly replaces a damaged or worn exterior door to restore the appliance's appearance and proper closure. It provides a durable replacement surface that helps keep the interior sealed and protected. What it does:

• Replaces cracked, dented, or cosmetically damaged outer door panels
• Restores proper door fit and helps maintain an effective interior seal
• Helps prevent drafts, moisture intrusion, and heat/cold loss related to a damaged exterior
• Matches OEM fit and mounting locations for straightforward replacement where applicable

• One outer door assembly

• Remove power and empty the appliance before starting; follow OEM service instructions
• Some installation steps may require removing trim, hinges, or internal panels—retain all fasteners
• Use proper tools and two people for alignment-heavy doors to avoid damage or injury

This Door Seal replaces the perimeter gasket on the appliance door so it closes snugly and maintains a proper barrier during operation. A fresh seal supports performance and helps reduce heat and moisture escaping around the door edge.

• Creates a continuous barrier between the door and front frame
• Helps maintain proper door fit and latching
• Replaces a torn, warped, or brittle seal that can cause leaks or a loose-feeling door
• Common symptoms include visible gaps, escaping steam/heat at the door, or needing extra force to close

• Disconnect power at the breaker before servicing; allow the unit to cool completely
• Open the door and remove any retaining trim/fasteners to release the old seal; avoid bending the door
• Clean the channel and press the new seal fully into place, ensuring an even, continuous fit around the perimeter

The Female Dryer Door Catch is an OEM part for Whirlpool dryers. It secures the dryer door in the closed position during operation, ensuring that the door remains firmly shut while the dryer is running. This catch works with the male door strike to provide a reliable latching mechanism.

Common causes of a bad door catch include repeated use leading to wear and tear, physical damage, or misalignment. A faulty door catch can prevent the dryer from operating correctly and may pose a safety hazard.

Symptoms of a bad female dryer door catch include:

• The dryer door not staying closed
• The dryer not starting due to the door not latching properly
• Difficulty in opening or closing the dryer door
• Visible damage to the door catch

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This is a replacement sheet-metal screw used to secure panels and components on compatible Whirlpool appliances. It provides a reliable fasten point for reattaching trim, brackets, and access panels after service. What it does:

• Secures appliance panels, brackets, and smaller components to the cabinet or frame
• Helps restore original fit and finish after repairs or part replacement
• Prevents rattles or loose panels when properly installed
• Matches OEM thread size and head style for a correct fit

• Turn off and unplug the appliance before removing panels or installing hardware
• Use the correct driver bit to avoid stripping the screw head
• Tighten until snug; avoid over-torquing to prevent thread damage or warped panels

This replacement screw secures panels, brackets, and internal components in your appliance. Replacing a missing or stripped screw restores a tight, rattle-free fit and helps keep parts properly aligned and protected during operation.

• Fastens appliance panels, brackets, and hardware in the designated locations
• Replaces missing, stripped, or corroded fasteners
• Helps reduce vibration noise and looseness from unsecured parts
• Restores proper fit and alignment after service or reassembly

• Disconnect power; turn off water supply before servicing
• Match the screw to the original location and replace one at a time to maintain alignment
• Use the correct driver; tighten snugly without overtightening to avoid stripping metal or cracking plastics
• If threads in the mating hole are damaged, repair/replace the clip or insert as specified in the service manual