Parts for Maytag MGDB855DC4: Door Parts

This outer refrigerator door panel replaces a damaged, dented, or cosmetically worn exterior door surface to restore the appliance's appearance and proper fit. It matches the original outer cabinet finish and attaches to the existing hinge and trim. What it does

• Replaces a scratched, dented, cracked, or otherwise damaged outer door surface.
• Restores a uniform exterior finish and helps the door close and align correctly.
• Works with the original internal liner, insulation, hinges and handle assembly.
• Helps prevent further damage to the door structure from impacts or corrosion.

• High-level: Requires removal of the old door panel and reattachment to factory hinges and trim; a second person is recommended for safe handling.
• Safety: Disconnect power and remove food/contents from door shelves before beginning work.
• Keep and reuse existing handle, trim, hinges, screws, and inner liner if they are not supplied.
• If alignment or sealing issues persist after installation, check hinge adjustments and gasket condition.

This bezel is the small trim ring that finishes and protects a control opening on your appliance. It helps center the control and restores a clean, factory look when the original trim is cracked or missing.

• Centers and supports a control knob or selector shaft
• Covers the raw panel opening to keep out debris
• Helps maintain proper knob alignment and feel
• Common signs it's needed: cracked or missing trim, loose/wobbly knob, uneven alignment, cosmetic damage

• Disconnect power to the appliance; also shut off gas before servicing
• Pull off the control knob, then remove the old bezel (release tabs or screws as designed)
• Note orientation; seat the new bezel fully and reinstall the knob
• Test control operation before returning the unit to service

This Door Catch Bezel, in white, is an OEM part for Whirlpool dryers. It secures the dryer door, making sure it remains closed during operation. Crafted precisely to fit compatible dryer models, this bezel guarantees a secure and snug fit.

What causes a bad part:
The Door Catch Bezel might deteriorate due to frequent use, exposure to heat, or physical strain during the opening and closing of the dryer door. Additionally, prolonged exposure to cleaning agents or moisture can contribute to its degradation.

Symptoms for a bad part:

• Difficulty in securely closing the dryer door
• Loose or shaky door closure
• Visible damage or cracks on the bezel

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This factory fastener secures appliance components such as panels, brackets, and handles. Replacing a missing or damaged screw restores a tight fit, reduces rattles, and helps keep parts aligned for smooth, reliable operation.

• Secures components to the appliance frame or assemblies
• Helps maintain alignment and structural stability
• Replaces missing, rusted, or stripped hardware
• Common symptoms include loose/wobbly handles or panels, rattling/vibration noises, or a visibly missing screw

• Disconnect power before servicing
• Use the correct driver/bit and start threads by hand to avoid cross-threading
• Do not overtighten; snug until secure
• Replace any that are corroded or stripped for an even hold

The Hinge is an OEM part for Whirlpool electric dryers. Located on the dryer door frame, this heavy-duty metal hinge securely holds the weight of the swinging door panel. It allows for easy opening, closing, and latching of the dryer entrance through thousands of cycles. 

Causes of a faulty hinge can include wear from years of operation putting pressure on the internal bearing as the door is repeatedly swung open and shut. Accidental impacts could also bend or damage hinge components over time.

Symptoms of a bad hinge include:

• Squeaking or grinding noises coming from the hinge area  
• Increased effort needed to open or close the door
• The door sagging when open or not staying still when closed
• Difficulty centering or aligning the door seal 

This Whirlpool dryer hinge is also compatible with brands including Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

The Hinge is an OEM part for Whirlpool electric dryers. Located on the dryer door frame, this heavy-duty metal hinge securely holds the weight of the swinging door panel. It allows for easy opening, closing, and latching of the dryer entrance through thousands of cycles. 

Causes of a faulty hinge can include wear from years of operation putting pressure on the internal bearing as the door is repeatedly swung open and shut. Accidental impacts could also bend or damage hinge components over time.

Symptoms of a bad hinge include:

• Squeaking or grinding noises coming from the hinge area  
• Increased effort needed to open or close the door
• The door sagging when open or not staying still when closed
• Difficulty centering or aligning the door seal 

This Whirlpool dryer hinge is also compatible with brands including Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

This cover is the outer console panel that protects and finishes the appliance's control area, restoring a clean appearance and shielding controls from dirt and moisture. It's the exact replacement piece used on compatible Whirlpool control assemblies. What it does

• Protects the control components and wiring from spills, dust, and everyday wear
• Restores the appliance's finished look by replacing a cracked, faded, or damaged console cover
• Helps keep buttons and switches aligned and accessible for reliable operation
• Prevents debris from entering the control cavity, which can reduce the risk of malfunctions

• One cover

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Remove any retaining screws or clips securing the old cover, then lift or slide it off per the service diagram
• Align the new cover with the mounting points and secure with the original fasteners—do not force or bend the part

The Dryer Door Catch is an OEM part for Whirlpool dryers. It keeps the dryer door securely closed during operation.

A bad door catch can occur due to regular use, wear and tear, or accidental damage. If you notice that the dryer door is not staying closed or is popping open during the drying cycle, it may indicate a problem with the door catch.

Symptoms of a bad door catch include:

• The dryer door not staying closed  
• Difficulty in properly latching the door shut
• Loud banging noises or vibrations 

Replace your faulty dryer door catch with this genuine OEM part to restore your dryer door. 

This Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

This replacement door seal restores a tight door-to-cabinet gasket to stop leaks and help the appliance operate reliably. It replaces worn, cracked, or torn seals so doors close securely and minimize water, air, and odor escape. What it does:

• Creates a secure seal between the door and cabinet to prevent water or air leaks.
• Helps reduce odors and protects internal components from moisture damage.
• Restores proper door closure to prevent puddles, drips, or inefficient operation.
• Commonly replaced when the existing seal is torn, stretched, or compressed.

• Disconnect power and water before starting; follow all safety precautions.
• Remove the old seal and clean the mounting surface before installing the new gasket to ensure a proper fit.
• Seat the gasket evenly into the door channel and verify the door closes fully with no gaps.
• After installation, run a short test cycle or inspection to confirm there are no leaks.

This replacement name plate restores the appliance's identification label so model and serial information is legible and the exterior looks complete. It's a simple cosmetic and identification part that helps owners read key appliance info. What it does

• Replaces a faded, damaged, or missing identification label
• Restores readable model/serial/manufacturer details for service and registration
• Improves cosmetic appearance where the original label is worn or peeled
• Helps prevent confusion when ordering parts or scheduling repairs

• One replacement name plate

• Clean and dry the mounting surface thoroughly before installing
• Align carefully and press firmly if adhesive-backed; use the original fasteners if applicable
• Handle by the edges to avoid transferring oils or smudges to the label

This plate is a replacement trim plate that restores the appliance's exterior fit and finish and helps protect underlying components from dirt and debris. It matches the original shape to secure and cover the intended area. What it does:

• Covers and protects the appliance surface or internal opening where installed
• Restores original appearance by replacing a worn, damaged, or missing plate
• Helps keep dust, spills, and debris away from components behind the opening
• Provides a mounting/attachment surface when fastened into place

• Disconnect power to the appliance before starting any repair to reduce shock and injury risk
• Remove any retaining screws or clips holding the damaged plate; save hardware if reusable
• Align the replacement plate and secure with original or OEM-recommended fasteners

This flat-head screw secures panels, brackets, or trim so they sit flush on your appliance. Replacing a worn or missing screw restores a tight fit and helps prevent vibration, rattling, or shifting components.

• Provides a countersunk, flush-mount fastener for panels, trim, brackets, or covers
• Helps maintain alignment and secure attachment during operation
• Replaces stripped, rusted, or missing hardware
• Symptoms can include loose panels or handles, rattling noises, or visible gaps/misalignment

• Disconnect power (and shut off gas, if applicable) before servicing
• Match screw length and thread to the original for proper fit
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Support the part being fastened to keep alignment while tightening