Parts for Whirlpool WED5100HC2: Door Parts

This name plate is the appliance identification label that displays model, serial and rating information and restores the unit's factory appearance. It helps ensure readable identification for service or resale. What it does

• Replaces a missing, faded or damaged identification label so model and serial info are visible.
• Provides required equipment ratings and manufacturer markings used during diagnostics and parts replacement.
• Restores exterior appearance where the original name plate is worn or peeling.
• Helps technicians and homeowners quickly confirm appliance identity during repairs.

• Name plate (single label)

• Disconnect power to the appliance before attempting installation or working near electrical connections.
• Clean and dry the mounting area; some name plates attach with adhesive while others fasten with screws—use the original hardware if present.
• Avoid bending or creasing the label when aligning it; press firmly to ensure full contact for adhesive-mounted plates.

This retainer clip secures small appliance components in place to prevent movement and ensure proper alignment for reliable operation. It's a simple replacement that restores lost or broken mounting support. What it does:

• Holds and stabilizes the attached component or assembly to prevent shifting during use
• Maintains proper alignment for connected parts to reduce wear and noise
• Commonly used where a small plastic or metal clip is needed for secure mounting
• Can address symptoms like loose panels, rattling, or parts that won't stay seated

• One retainer clip

• Disconnect power to the appliance before attempting any repair
• Remove surrounding panels as needed to access the clip; small trim tools may help
• Replace the broken retainer with the new clip and verify the secured component is seated correctly

This is a replacement sheet-metal screw used to secure panels and components on compatible Whirlpool appliances. It provides a reliable fasten point for reattaching trim, brackets, and access panels after service. What it does:

• Secures appliance panels, brackets, and smaller components to the cabinet or frame
• Helps restore original fit and finish after repairs or part replacement
• Prevents rattles or loose panels when properly installed
• Matches OEM thread size and head style for a correct fit

• Turn off and unplug the appliance before removing panels or installing hardware
• Use the correct driver bit to avoid stripping the screw head
• Tighten until snug; avoid over-torquing to prevent thread damage or warped panels

This replacement seal restores a tight barrier at its mounting point in your appliance. It helps prevent leaks and maintains performance by ensuring a proper fit between connected components where fluids or air must be contained. Location varies by model.

• Creates a reliable seal between mating parts to contain water or air
• Helps stop drips, seepage, and unwanted airflow that can affect performance
• Replace if cracked, flattened, swollen, or leaking
• Common symptoms: moisture under/around unit, residue, or diminished efficiency
• Direct-fit replacement to match the original part's size and profile

• Disconnect power and, if applicable, shut off water supply before servicing
• Note the original seal's orientation; clean and dry all sealing surfaces
• Lightly moisten or use only manufacturer-approved lubricant; avoid petroleum products unless directed
• Seat evenly without twisting; after reassembly, run a test cycle and check for leaks

This inner oven door glass provides a clear, heat-resistant viewing panel so you can monitor cooking without opening the door. Restores the oven door's visibility and helps maintain proper oven sealing when installed correctly. What it does:

• Replaces the inner glass panel that fits inside the oven door assembly.
• Allows safe viewing of food while helping the door retain heat.
• Commonly replaced when glass is cracked, chipped, or fogged.
• Helps prevent heat loss and supports proper oven operation when intact.

• One inner oven door glass panel (single piece as shown)

• Handle carefully—tempered glass can shatter if dropped or struck.
• Follow the oven manufacturer's service manual for disassembly/reassembly steps.
• Disconnect power to the appliance before beginning any repair.
• If clips, gaskets, or mounting hardware are damaged, replace them as needed.

The Dryer Door Hinge Assembly is an OEM part for Whirlpool electric and gas dryers. As a critical component, this assembly supports the dryer door and allows for smooth opening and closing. 

Causes of failure include frequent use, which causes hinge components like bushings and bearings to wear out more quickly over time. Housing cracks or mechanical loosening from repeated operation are other issues.

Symptoms of a faulty door hinge assembly include: 

• Door that won't stay closed securely or slams shut on its own   
• Difficulty smoothly opening and closing the door
• Excessive gaps around the edges that allow lint to escape

This genuine Whirlpool replacement fits Maytag, Amana, Jenn-Air, Magic Chef, and select Kenmore dryers.

This flat-head screw secures panels, brackets, or trim so they sit flush on your appliance. Replacing a worn or missing screw restores a tight fit and helps prevent vibration, rattling, or shifting components.

• Provides a countersunk, flush-mount fastener for panels, trim, brackets, or covers
• Helps maintain alignment and secure attachment during operation
• Replaces stripped, rusted, or missing hardware
• Symptoms can include loose panels or handles, rattling noises, or visible gaps/misalignment

• Disconnect power (and shut off gas, if applicable) before servicing
• Match screw length and thread to the original for proper fit
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Support the part being fastened to keep alignment while tightening

This factory fastener secures appliance components such as panels, brackets, and handles. Replacing a missing or damaged screw restores a tight fit, reduces rattles, and helps keep parts aligned for smooth, reliable operation.

• Secures components to the appliance frame or assemblies
• Helps maintain alignment and structural stability
• Replaces missing, rusted, or stripped hardware
• Common symptoms include loose/wobbly handles or panels, rattling/vibration noises, or a visibly missing screw

• Disconnect power before servicing
• Use the correct driver/bit and start threads by hand to avoid cross-threading
• Do not overtighten; snug until secure
• Replace any that are corroded or stripped for an even hold

Fiberglass-reinforced door seal that restores an appliance door's airtight closure to help maintain consistent temperatures, reduce energy waste and minimize frost or moisture buildup around the door. What it does:

• Forms a continuous gasket around the door to keep cold air in and warm air out.
• Helps prevent frost buildup and uneven temperatures caused by air leaks.
• Common symptoms that indicate replacement: visible gaps, cold-air leakage, frost/ice at the door, or a door that won't seal flush.
• Fiberglass construction helps the seal retain shape for a more reliable long-term closure.

• Disconnect power to the appliance before beginning any service.
• Remove the old seal and clean the door channel; press the new seal evenly into place, checking for full contact around the perimeter.
• Some models may require partial door or liner removal—before disassembly.
• If the seal is stiff, follow OEM-recommended conditioning (allow to warm to room temperature or use manufacturer guidance) to help it seat properly.