Parts for Whirlpool WED8700EC0: 05 - Door Parts

This complete outer oven door assembly restores a damaged or non-sealing oven door so the appliance retains heat and operates safely. It replaces a worn, dented, or cracked exterior door section with an OEM-fit assembly. What it does

• Provides the exterior panel, handle area, and mounting points needed for a secure oven door closure
• Restores proper sealing to help maintain oven temperature and cooking performance
• Eliminates drafts, rattling, or visible exterior damage from dents or cracks
• Helps prevent heat escape that can affect bake/roast results or trigger safety concerns

• One complete outer oven door assembly

• Disconnect power to the appliance before beginning any repair
• Door assemblies can be heavy or awkward—have a second person or secure support when removing/installing
• Follow OEM instructions for hinge alignment and fastener torque to ensure proper operation
• Inspect door glass and seals during installation; replace any damaged gaskets or clips per OEM guidance

This bezel is the small trim ring that finishes and protects a control opening on your appliance. It helps center the control and restores a clean, factory look when the original trim is cracked or missing.

• Centers and supports a control knob or selector shaft
• Covers the raw panel opening to keep out debris
• Helps maintain proper knob alignment and feel
• Common signs it's needed: cracked or missing trim, loose/wobbly knob, uneven alignment, cosmetic damage

• Disconnect power to the appliance; also shut off gas before servicing
• Pull off the control knob, then remove the old bezel (release tabs or screws as designed)
• Note orientation; seat the new bezel fully and reinstall the knob
• Test control operation before returning the unit to service

This factory fastener secures appliance components such as panels, brackets, and handles. Replacing a missing or damaged screw restores a tight fit, reduces rattles, and helps keep parts aligned for smooth, reliable operation.

• Secures components to the appliance frame or assemblies
• Helps maintain alignment and structural stability
• Replaces missing, rusted, or stripped hardware
• Common symptoms include loose/wobbly handles or panels, rattling/vibration noises, or a visibly missing screw

• Disconnect power before servicing
• Use the correct driver/bit and start threads by hand to avoid cross-threading
• Do not overtighten; snug until secure
• Replace any that are corroded or stripped for an even hold

A direct-replacement outer door assembly that restores a secure, finished closure and helps keep heat and moisture contained. Designed to fit the original mounting points for a factory-style repair. What it does:

• Replaces a cracked, dented, or cosmetically damaged outer door to restore appearance and sealing
• Provides a stable mounting surface for the inner window and latch components
• Helps prevent heat or steam from escaping during operation
• Reduces rattling or vibration caused by a bent or loose door

• Disconnect power and allow the appliance to cool before starting any repair
• Use appropriate hand tools and keep track of removed screws and fasteners for reassembly
• Align door hinges and latch carefully; test operation before returning the appliance to service
• Replace those parts separately as needed

The Hinge is an OEM part for Whirlpool electric dryers. Located on the dryer door frame, this heavy-duty metal hinge securely holds the weight of the swinging door panel. It allows for easy opening, closing, and latching of the dryer entrance through thousands of cycles. 

Causes of a faulty hinge can include wear from years of operation putting pressure on the internal bearing as the door is repeatedly swung open and shut. Accidental impacts could also bend or damage hinge components over time.

Symptoms of a bad hinge include:

• Squeaking or grinding noises coming from the hinge area  
• Increased effort needed to open or close the door
• The door sagging when open or not staying still when closed
• Difficulty centering or aligning the door seal 

This Whirlpool dryer hinge is also compatible with brands including Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

The Hinge is an OEM part for Whirlpool electric dryers. Located on the dryer door frame, this heavy-duty metal hinge securely holds the weight of the swinging door panel. It allows for easy opening, closing, and latching of the dryer entrance through thousands of cycles. 

Causes of a faulty hinge can include wear from years of operation putting pressure on the internal bearing as the door is repeatedly swung open and shut. Accidental impacts could also bend or damage hinge components over time.

Symptoms of a bad hinge include:

• Squeaking or grinding noises coming from the hinge area  
• Increased effort needed to open or close the door
• The door sagging when open or not staying still when closed
• Difficulty centering or aligning the door seal 

This Whirlpool dryer hinge is also compatible with brands including Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

The Dryer Door Catch is an OEM part for Whirlpool dryers. It keeps the dryer door securely closed during operation.

A bad door catch can occur due to regular use, wear and tear, or accidental damage. If you notice that the dryer door is not staying closed or is popping open during the drying cycle, it may indicate a problem with the door catch.

Symptoms of a bad door catch include:

• The dryer door not staying closed  
• Difficulty in properly latching the door shut
• Loud banging noises or vibrations 

Replace your faulty dryer door catch with this genuine OEM part to restore your dryer door. 

This Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

This replacement door seal restores a tight door-to-cabinet gasket to stop leaks and help the appliance operate reliably. It replaces worn, cracked, or torn seals so doors close securely and minimize water, air, and odor escape. What it does:

• Creates a secure seal between the door and cabinet to prevent water or air leaks.
• Helps reduce odors and protects internal components from moisture damage.
• Restores proper door closure to prevent puddles, drips, or inefficient operation.
• Commonly replaced when the existing seal is torn, stretched, or compressed.

• Disconnect power and water before starting; follow all safety precautions.
• Remove the old seal and clean the mounting surface before installing the new gasket to ensure a proper fit.
• Seat the gasket evenly into the door channel and verify the door closes fully with no gaps.
• After installation, run a short test cycle or inspection to confirm there are no leaks.

This name plate is the decorative centennial badge that restores the appliance's exterior appearance and branding. It replaces a missing, damaged, or faded badge to keep the unit looking factory-finished. What it does

• Restores the appliance's exterior badge for a like-new appearance
• Replaces badges that are cracked, scratched, peeling, or discolored
• Helps identify the appliance style when the original emblem is missing
• Cosmetic part only — does not affect appliance operation

• One name plate

• For best results, clean the mounting area and remove dirt or wax before installation
• Handle carefully to avoid scratching the finish; use non-marring tools as needed
• If access behind trim is required, unplug the appliance or disconnect power before removing panels
• Follow OEM instructions for removal and reinstallation to avoid damaging clips or surrounding trim

This flat-head screw secures panels, brackets, or trim so they sit flush on your appliance. Replacing a worn or missing screw restores a tight fit and helps prevent vibration, rattling, or shifting components.

• Provides a countersunk, flush-mount fastener for panels, trim, brackets, or covers
• Helps maintain alignment and secure attachment during operation
• Replaces stripped, rusted, or missing hardware
• Symptoms can include loose panels or handles, rattling noises, or visible gaps/misalignment

• Disconnect power (and shut off gas, if applicable) before servicing
• Match screw length and thread to the original for proper fit
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Support the part being fastened to keep alignment while tightening