Parts for Whirlpool WMH53520CB3: 03 - Door Parts

The Microwave Door is an OEM part for Whirlpool microwaves. It provides access to the cooking cavity while also serving to safely contain microwave emissions. Made of glass, the door allows for easy visibility of foods inside without interfering with cooking performance. 

Symptoms of a bad microwave door include:

• Cracks or chips in the glass that could weaken containment
• Difficulty opening or closing the door smoothly 
• Warping or sagging of the door frame over time
• Leaks that allow the escape of microwave radiation 

Causes of a bad door can be repeated stress from opening and closing, accidental damage, or failure of hinges or latching mechanisms. Improper sealing also risks safety. 

It is compatible with kitchen appliances from Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and Kenmore as well.

This complete microwave door assembly replaces a damaged or non-sealing door to restore proper closure, heat containment, and user access. It includes the outer door, inner liner, handle area, and latch interface in one ready-to-install unit. What it does:

• Replaces a cracked, dented, or warped door that won't close or latch properly
• Restores the microwave's ability to contain heat, sparks, and cooking odors
• Re-establishes the door latch engagement so the oven recognizes door-closed status
• Improves user access when original door handle or hinge area is broken

• Turn power off at the breaker and unplug the microwave before servicing
• Some models require partial disassembly of the microwave cabinet to remove and install the door; follow the OEM service manual
• Handle and mounting hardware may be pre-attached; confirm fit before tightening screws

This door handle is a direct-replacement part designed to restore proper grip and function to your appliance door. It fits the original mounting points and gives a secure, easy-to-use handle for everyday opening and closing. What it does:

• Provides a secure grip to open and close the appliance door reliably
• Replaces a cracked, loose, or broken handle to restore normal operation
• Matches original mounting holes for a straightforward fit
• Helps prevent further damage from forcing the door if the handle has failed

• One door handle

• Basic hand tools required; do not overtighten fasteners to avoid cracking
• Disconnect power and empty door contents before starting
• Handle mounting screws or clips may be behind trim—refer to your model's service guide

Color: White

Color: Black

Color: White

Color: Black

This outer door panel restores a refrigerator door's exterior appearance and structural integrity. It replaces a dented, cracked or rusted outer door surface to make the appliance look and function like new again. What it does:

• Replaces the refrigerator door's external panel to repair visible damage or corrosion
• Restores a smooth, finished exterior and consistent trim alignment
• Helps protect internal components housed in the door from impact and moisture
• Addresses common symptoms like dents, deep scratches, paint chipping or separated outer trim

• Installation typically requires removing the door from the cabinet and transferring hardware (hinges, handle, trim, insulation) from the old door
• Tighten fasteners to manufacturer torque and verify door alignment and swing after installation
• Keep wiring and insulation protected when separating inner and outer door pieces

This door latch is the replacement latching mechanism that secures the appliance door during operation, restoring proper door closure and safe operation. It fits the factory mounting and engages/disengages the door as designed. What it does:

• Secures the door closed so the appliance can run and maintain temperature or cycle safety systems
• Replaces a broken, worn, or loose latch that won't hold the door shut
• Commonly used when the door won't stay closed, won't latch, or the appliance won't start because the door is not detected as closed
• Engages with the door strike to ensure a positive, spring-loaded closure

• One door latch

• Disconnect power (unplug or switch off breaker) before beginning any repair
• Access may require removing the oven/dryer front panel or door trim
• Align the latch with the mounting holes and secure with the original screws; test latch operation before fully reassembling
• If electrical connectors are present, ensure they are fully seated and undamaged