Parts for Frigidaire FGHT2055VD1: Doors Parts

This gasket creates a tight seal between mating surfaces inside your appliance to prevent air or water leakage. Replacing a worn seal restores proper containment, helping the unit maintain performance, temperature control, and efficiency.

• Seals the joint between components to keep air and moisture from escaping or entering
• Helps the unit maintain stable temperatures and proper operation
• Replace if cracked, deformed, brittle, or no longer sealing
• Common symptoms: visible damage, leaks, condensation, or reduced performance due to poor sealing

• Disconnect power; shut off water supply if your repair involves any water connections
• Note the orientation of the original gasket before removal
• Clean and dry all mating surfaces; remove old adhesive or residue as needed
• After installation, run a quick test and check for leaks or gaps around the seal

This complete door assembly replaces a damaged or worn fridge door to restore proper closing, insulation, and appearance. It provides the full outer door structure so the appliance seals and functions as intended. What it does:

• Replaces a dented, cracked, or warped door to restore proper fit and sealing
• Helps stop drafts and maintains internal temperature when the door closes correctly
• Restores exterior appearance and provides mounting for handle, trim, and hinges
• Addresses symptoms like visible damage, poor closing, or gaps at the cabinet

• One complete door assembly as shown

• Disconnect power and remove food from affected compartment before starting
• This is a heavy, full-door component—use a second person to support the door during removal/installation
• May require hinge alignment and adjustment after installation; use manufacturer instructions for torque and positioning

A replacement refrigerator bin that stores and organizes food items to help keep shelves tidy and accessible. Fits into compatible shelf tracks and restores usable storage space in the fresh-food compartment. What it does:

• Holds fruits, vegetables, deli items, or other refrigerated goods for easy access and organization
• Slides or rests on shelf tracks to form a secure storage receptacle
• Replaces cracked, chipped, or discolored bins that no longer seal or support contents
• Helps prevent small items from rolling or tipping on the shelf

• One replacement refrigerator bin

• Remove all food and shelves near the install area before replacing the bin
• Slide or set the bin into the shelf tracks until it seats securely (no tools typically required)
• Inspect surrounding tracks and supports for damage; replace if worn to ensure proper fit
• Clean the bin with mild detergent and warm water; avoid abrasive cleaners

This clear replacement crisper drawer stores fruits and vegetables and restores organized storage in the refrigerator. It fits into existing tracks and provides a sealed, easy-access compartment for fresh produce. What it does:

• Replaces a cracked, chipped, or broken crisper/drawer to restore storage capacity
• Keeps produce separated from main shelves to help prevent bruising and cross-contamination
• Slides into existing tracks for smooth in-and-out access
• Prevents items from falling onto lower shelves when drawer is closed

• Disconnect power only if working inside the refrigerator to avoid accidental contact with components
• Empty the drawer and remove any shelves or stops blocking removal before pulling the old bin out
• Align the bin with the tracks and slide it in until it seats; verify smooth operation
• If the bin does not seat easily, check for obstructions or damaged tracks before forcing

Replacement refrigerator bin that restores storage space and keeps foods contained and visible. Clear plastic construction helps you organize produce and deli items while preventing spills and shifting during normal use. What it does:

• Replaces a cracked, broken or missing refrigerator drawer so food stays contained and off shelving
• Slides into the refrigerator's bin rails to create an organized storage area for produce, deli items or packaged goods
• Clear design makes it easy to see contents without removing the bin
• Helps prevent spills from spreading when a shelf is bumped or an item tips

• Typically installs by sliding into the existing bin rails; no tools required for most models
• Inspect rails and mounting tabs for damage before installing; damaged rails may need replacement
• Clean with mild detergent and warm water; avoid abrasive pads and harsh chemicals

This bearing supports and allows smooth rotation of the dryer drum, helping reduce noise and wear. Replacing a worn bearing restores stable drum movement and helps prevent scraping, thumping, or drag during cycles.

• Supports the rear of the drum for proper alignment and smooth rotation
• Can help address squeaking, grinding, scraping, or thumping sounds
• Reduce drum wobble, drag, or intermittent stopping during operation
• Wear item that can degrade over time with heat and load stress

• Disconnect power before service and allow components to cool
• Access typically requires removing the top and front panels
• Inspect the drum shaft, support bracket, and glides for wear; replace if needed
• Apply manufacturer-approved high-temp lubricant where specified

The Hook is an OEM part for Frigidaire refrigerators. It helps to ensure a secure and proper closure of the refrigerator door.

A bad door closer hook can be caused by wear and tear, damage, or misalignment. Signs of a faulty door closer hook include the door not closing fully or not staying closed, difficulty in opening or closing the door smoothly, or a loose or wobbly door.

Symptoms of a bad door closer hook can include:

• The refrigerator door not sealing properly
• Excessive force required to open or close the door
• Visible damage or misalignment of the door closer hook

Replace your worn or damaged door closer hook with this genuine OEM part to restore your refrigerator door. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This factory screw secures interior or door components in your refrigerator so they stay tight and aligned. Replace missing, stripped, or corroded hardware to eliminate looseness and prevent parts from shifting or rattling during use.

• Fastens brackets, trim, rails, bins, or handles to the cabinet or door
• Restores a secure fit when the original screw is lost, damaged, or rusted
• Helps correct looseness, vibration, and rattling from unsecured parts
• Common symptoms: loose or wobbling handle/trim, misaligned parts, missing hardware

• Disconnect power to the appliance before servicing; turn off water if working near dispenser/ice areas
• Match to the original hardware and install in the same location; reuse any washers/spacers
• Start threads by hand to prevent cross-threading; use the correct driver bit
• Tighten snugly—do not overtighten to avoid stripping threads or cracking plastic

Replacement door magnet that helps the refrigerator or freezer door stay closed for a tighter seal and more consistent cooling. Restores magnetic hold so doors close reliably and reduce warm spots. What it does

• Provides magnetic hold for the door liner so the door stays shut during normal use
• Helps maintain the gasket engagement to preserve internal temperature
• Common symptom: door not staying closed, food warming, or frost build-up near the door
• Used in door/gasket assembly where magnets secure the seal

• Turn off power to the appliance or unplug before removing door trim or accessing internal components
• Remove door liner or gasket per service instructions to access and replace the magnet; keep fasteners and seals intact
• Press or seat magnet into its channel or mounting location; use the OEM fastener or adhesive method specified by the manufacturer