Parts for Lg LRG3091SW: Drawer Parts

This replacement screw secures panels, trim and internal components to restore a tight fit and stop rattling or loose parts. Use it when a missing or stripped screw causes panels or controls to shift. What it does:

• Secures panels, trim pieces or mounting brackets to keep components aligned
• Stops rattling, vibration noise or loose-fitting panels
• Replaces missing or stripped screws to restore proper fastening
• Helps ensure other parts stay in position during normal use

• Disconnect power before working on the appliance to prevent shock or injury
• Use the correct screwdriver or bit to avoid stripping the head
• Thread carefully and tighten until snug; avoid overtightening which can strip threads or crack plastic
• Replace with the exact OEM screw if available to ensure proper fit and function

This factory-specified fastener secures designated panels and components, restoring a precise fit and helping keep your appliance solid and quiet. Replace a missing, stripped, or rusted original with the correct OEM match for the specified locations.

• Secures brackets, panels, and internal parts where this part number is called out
• Replaces damaged, stripped, corroded, or lost screws
• Helps reduce looseness and vibration that can cause rattling noises
• Exact OEM replacement for positions requiring this specific screw

• Disconnect power and shut off water/gas before servicing
• Match to the removed screw and install only in the locations specified for this part number
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening, especially into plastic
• If multiple screws are involved, start all fasteners before final tightening to ensure alignment

This idler bracket mounts the idler pulley or roller in your appliance's tensioning system, keeping a belt or cable aligned and properly tensioned for consistent operation. A bent or worn bracket can cause noise, slippage, or loss of motion.

• Secures the idler pulley/roller in the correct position
• Maintains proper belt/cable tension and alignment
• Helps reduce squealing or squeaking from friction/misalignment
• Can address belts/cables coming off or intermittent movement in the drive mechanism

• Disconnect power; also shut off gas or water before servicing
• Access the tensioner area and note the belt/cable routing and spring orientation
• Relieve tension, remove the old bracket, and transfer the pulley/roller and any spring or hardware as required
• Reinstall the bracket, ensure smooth free movement, route belt/cable correctly, and test operation

This guide rail is the drawer slide that supports and guides a refrigerator or freezer drawer for smooth, stable opening and closing. It restores proper drawer alignment and prevents sticking or sagging for easier access. What it does:

• Supports and guides the drawer along its track for consistent movement
• Keeps the drawer aligned to prevent binding, wobbling, or uneven closing
• Reduces noise and catching during opening and closing
• Helps prevent the drawer from falling out or becoming detached when pulled

• Remove food and drawers before replacing the rail to avoid damage or injury
• Use appropriate hand tools; avoid forcing parts to prevent breakage
• Disconnect power to the appliance if panel removal requires access to electrical components

This water inlet valve controls water flow to the ice maker and dispenser, restoring proper fill and supply so your refrigerator can make ice and deliver water on demand. Replaces a failed or leaking valve to stop drips and restore normal operation. What it does:

• Opens and closes to allow water into the ice maker and dispenser when requested
• Stops water flow to prevent overfilling and leaking when closed
• Commonly replaces valves that cause no water dispensed, slow fills, or continuous leaking
• Operates as the sealed solenoid valve that the refrigerator's control uses to meter water

• Disconnect power and shut off the water supply before starting any repair
• Replace only with the exact part number shown for fit; secure all water and electrical connections
• After installation, turn on water and power, then check for leaks and proper fill operation

This door handle mounting anchor creates the fixed attachment point on the appliance door or drawer. Replacing a worn or missing anchor restores a solid, wobble-free handle and a consistent feel when opening and closing.

• Provides the secure mounting point that the handle fastens to
• Helps keep the handle aligned and rigid during use
• Replace if the anchor is cracked, stripped, or missing
• Resolve a loose/wobbly handle, a handle that won't tighten, or misalignment after service

• Disconnect power; turn off the water supply
• Protect the door/drawer finish and support the handle during removal
• Remove the handle per your model's instructions and take out the damaged anchor
• Install the new anchor using the existing mounting location/hardware, seat the handle fully, then tighten set screws evenly without overtightening

This parts assembly is a replacement module that restores the specific component group in compatible LG appliances, helping return the affected feature to normal operation. Use it to replace a worn or failed factory assembly. What it does

• Replaces a multi-piece component assembly used in the appliance's subsystem.
• Restores function when the original assembly shows signs of failure or intermittent operation.
• Common symptoms it can address: subsystem not responding, intermittent errors, or a feature that no longer operates reliably.
• Designed to match the original OEM form and connectors for a direct replacement.

• Disconnect power and water before starting any service.
• Handle connectors and wiring carefully; match connectors and routing to avoid pin damage or misalignment.
• Reuse factory mounting hardware unless replacement fasteners are required.
• Follow the OEM instructions for safe, correct installation.