Parts for Husqvarna HU700F-96145000903: Engine / Housing / Handle Parts

This bail control arm is a genuine Husqvarna part, sold individually. This bail control arm can be used as a replacement part for a lawnmower. This bail control arm works in conjunction with the handle so that when the operator pulls the bar, the engine is started and when the bar is released, the engine stops.The bail control arm might have to be replaced if it no longer serves its function for a lawnmower. This could occur if the bail control arm is damaged as a result of general wear and tear over long-term usage or from a direct impact that warps the component. If the engine does not engage when the bail control arm is pulled or the engine remains powered on when the arm is released, the component should be replaced by this genuine OEM replacement part. Remember to wear work gloves as a safety precaution while repairing or replacing parts within an outdoor appliance. This is an OEM part sourced directly from the manufacturer. It is sold individually. This bail control arm is compatible with the following outdoor appliance brands: Husqvarna and Poulan.

This genuine Husqvarna rear skirt provides protection from grass clippings and debris that could fly from underneath the lawn mower during use. Periodic inspection of the rear mower skirt for cracks and damage is an important safety measure for lawn mowers. Do not attempt to remove or install the rear skirt when the lawn mower is running. For models with clip-fasteners: Use a flathead screwdriver to remove the old skirt from the lawn mower. Line the new skirt up and reinstall the clips. For models with screw fasteners: Remove the screws holding the skirt in place, set screws aside for reuse. After removing the old rear skirt, clean the area to remove any dirt or debris. Flush installation is important in preventing debris flyout. Line the holes on the new skirt with the holes on the lawn mower. Reinstall screws and tighten. Dispose of the old skirt. The OEM skirt is made of high-quality, molded, composite black plastic. The unit is sold individually. This rear skirt does not include fastening clips or screws. Reuse fasteners on the current mower. This rear skirt compatible for use with Craftsman and Husqvarna push lawn mowers.

This flanged hex nut is used in various models of lawn and garden equipment. The nut is considered a standard hardware part that may have multiple applications on different units. It is typically used along with a bolt or screw to provide a secure hold for various components. This nut is a small part and can become lost in the process of other repairs. It can also break or strip the threads due to regular wear and tear, impact damage, or another issue. If this nut is broken or missing, it needs to be replaced immediately. Replacing the hex nut with a genuine OEM part will ensure equipment is always in proper working order. This OEM hex nut is designed for use in select Craftsman and Husqvarna equipment. It is manufactured by Husqvarna as an exact replacement for the original nuts that came with the machine. This part can fit on more than 150 machines, including lawn mowers, tractors, snow blowers, and trimmers from both brands. Owners will want to check their parts diagram for the exact location(s) and application(s) of this nut. Since it is standard hardware, some people purchase multiple quantities to keep extra parts on hand in case of emergency.

This screw is a genuine Husqvarna part, sold individually. This screw can be used as a replacement part for a lawn mower. The purpose of the screw is to secure and affix components to one another.If a screw is misplaced or lost and this causes two components or more to be separated from one another, the screw should be immediately replaced. Screws can also be stripped or can suffer general wear and tear over time; if this occurs, the screw should be removed and replaced by this genuine OEM replacement part before further damage is caused. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This is an OEM part sourced directly from the manufacturer. It is sold individually. This screw is compatible with the following outdoor appliance brands: Husqvarna, Craftsman, and Poulan.

This replacement part is a bolt. This is a genuine replacement part made by Husqvarna. This part is small but very important in many machines and devices. The bolt itself is able to hold things in place, similar to a screw or nut. A new bolt might be needed if the current one is missing or damaged in any way. This can include being dented, stripped, or lodged in place. The repair should be fairly easy and might only require household tools. If the previous bolt is lodged in place the user might need pliers to retrieve it. Be sure to wear work gloves during this repair. It is also recommended that the machine be completely powered down before replacing this part. This is a genuine OEM replacement part. This part is sold individually and is sourced directly from the manufacturer to ensure proper fit.

This genuine Husqvarna selector knob affixes to the selector spring as part of a mechanism that lowers and raises the handle of the lawn mower for flexible usage.The selector knob might have to be replaced in the event that it suffers damage that impedes its ability to lower and raise the handles of the lawn mower. This kind of damage can occur as a result of general wear and tear from long-term usage, exposure to the elements, or a direct collision that warps the selector knob beyond repair. If any of this form of damage occurs and prevents the adjustability of the handles, the selector knob should be replaced with this genuine OEM replacement part. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This is an OEM part sourced directly from the manufacturer. It is sold individually. This selector knob is compatible with the following brands: Husqvarna, Poulan, Ariens, and Craftsman.

This replacement part is a height adjuster, and it is intended for use in different types of lawn equipment. This is a genuine replacement part made by Husqvarna. This part is commonly found in riding lawn mowers and is used to adjust the cutting height of the blades. The user is able to move the wheel up or down to select the desired cutting height of the grass before use. A new height adjuster might be needed if the current plate is damaged. This means that the height of the blade is unable to be adjusted. It is common that this part might need to be replaced after years of normal wear and tear, as it is in contact with rough terrain. Be sure to wear work gloves while replacing this part as the cutting blades are typically exposed. To replace this part the user will need a screwdriver and two types of nuts.This part is a genuine OEM replacement part sourced directly from the manufacturer.

A clipping deflector is a lawnmower attachment designed to guide and direct grass clippings away from the equipment itself. When attached, it allows the lawnmower to transform into a side discharge tool. It is made from flexible plastic material. If it develops cracks and holes or its attachment hooks break, the clipping deflector needs to be replaced. It is a quick and straightforward process that requires no tools. The deflector is located beneath the mulch door. Simply hold the mulch cover and lift it up. Use your other hand to pull the broken deflector away from the mulch cover hinge pin. Then, attach the new deflector's tab into the mulch's hinge pin. Lastly, lower the mulch cover to its original position. This brand-new, OEM Husqvarna clipping deflector replacement is explicitly made for Craftsman and Husqvarna lawnmower models. This replacement part is sold individually.

This part is a replacement handle bracket assembly. This is a genuine OEM part made by Husqvarna and has been sourced directly from the manufacturer. This part can be used to replace a broken or defective handle bracket assembly in lawn mowers.This handle bracket assembly allows the lawn mower handle to be securely fixed in place so it doesn't move. If the lawn mower handle is not secured or moves during operation, it may be difficult for the user to properly maneuver the mower. It's important when working on or near any engine to make sure the equipment is powered off and completely cooled down before starting any repairs. For more accurate information on how and where to install this handle bracket, the appropriate owner's manual and equipment diagrams should be referred to. As an authentic replacement part, this handle bracket assembly is suitable for use on several models of lawn mowers manufactured by Husqvarna, Poulan, and other brands. This is a genuine part made of high-quality, durable metal and is sold individually.

This bolt is a genuine OEM replacement part sourced directly from the manufacturer. It is designed for use with outdoor power equipment like lawnmowers and snowblowers. This bolt is a hex thread rolling bolt with the nut included. This type of bolt is designed to go into pre-drilled holes, such as on an engine. The hex threads on the bolt push the material through the hole, and the nut is then applied to secure the bolt. Bolts should be inspected as part of routine maintenance to ensure the nut is tightly secured and that the bolt has not rusted or come out. If a rusted bolt is discovered or a bolt is missing from the equipment, this replacement bolt can be used. Before replacing or installing a part on the equipment, allow it to cool and then remove the spark plug from the unit. Gloves should be worn when working with the unit. Install the new bolt and tighten the included nut. This bolt is a hex threaded, 3/8-16 x 1-1/8 bolt made of durable black metal and includes the nut. It is compatible with lawnmowers, snow blowers, trimmers, and lawn tractors manufactured by Husqvarna, Poulan, Weed Eater, Murray, and Craftsman.

This part is a replacement torsion spring. This is a genuine OEM part made by Husqvarna and has been sourced directly from the manufacturer. It is intended to replace a defective torsion spring in lawn mowers.This torsion spring is what enables the mower's deflector shield to be easily moved up and down. Springs are subject to wear and tear and may become stretched, rusted, corroded, or snapped, requiring replacement. Wear work gloves to protect the hands and check that equipment is powered off and cooled down before starting the repair process. For more accurate information on how and where to use this torsion spring, the appropriate owner's manual and equipment diagrams should be referred to. This nut is a genuine OEM part made of durable metal and is sold individually. It is suitable for use with lawn mower models that have been manufactured by Husqvarna, Poulan, and other brands.

This hinge rod is a genuine Husqvarna part, sold individually. This hinge rod can be used as a replacement part in a lawnmower. The purpose of a hinge rod in a lawnmower is to affix to the discharge chute so that the chute has a range of motion while remaining attached to the appliance to fulfill its function.The hinge rod in a lawnmower might have to be replaced if it is damaged. The hinge rod could be punctured, scraped, dented, cracked, or eroded to the point that the hinge rod can no longer affix to the discharge chute or that the component is loosened to the point that a repair cannot fix it. If this occurs, the hinge rod should be removed and replaced by this genuine OEM replacement part.This component is a genuine OEM replacement part, sourced directly from the manufacturer. It is sold individually. This hinge rod is compatible with the following outdoor appliance brands: Husqvarna, Craftsman, Weed Eater, Ariens, Murray, and Poulan.

This adapter attaches the blade to the motor shaft and can ensure a secure fit for the size of the blade that you need. The adapter will hold the blade in place and allow it to rotate appropriately. Although this piece is made of metal, it can wear down with regular use over time and may need to be replaced. It could also become damaged, which would require a more immediate replacement. Either way, this genuine OEM blade adapter can provide a solution for compatible mowers. This blade adapter is reasonably simple to install, but always disconnect the spark plug before doing any work. The Craftsman blade adapter can be used as a replacement part on compatible lawnmowers models from Craftsman, Husqvarna, Poulan and Poulan Pro, Weed Eater, EHP, Yard Pro, Sears, Rally, and Roper.

This is a four-in-one blade that is used for push mowers from several manufacturers. It is used for shredding and mulching leaves. This provides users with more options when cutting the grass on their lawns. If the blade is not working properly, it will limit the functionality of the mower.The metal blade on a mower is durable and meant to last. However, accidents such as running over stumps or rocks could cause the blade to bend or break. Older blades could become worn down and chipped. In some cases, the metal may even begin to corrode. Regardless of what causes the damage, owners need to change the blade out when it no longer works correctly. When replacing the part, users should wear work gloves to protect their hands. This blade works for certain models of push mowers from Husqvarna and Jonsered. It is sold individually and is a genuine OEM replacement blade sourced from the manufacturer.

This replacement part is a bolt and is intended for use in different types of lawn equipment. This is a genuine replacement part made by Husqvarna. A bolt is a small but important part in many tools. These parts are able to hold different areas of machinery together so that the different areas of the device stay secure and steady. A new bolt might be needed if the current ones are missing or damaged. If parts on the appliance are falling off or are loose, the user should look into replacing a bolt. To replace a bolt or many bolts, the user must have access to common household tools. Simply remove the old one and use a screwdriver to replace it with a new part. Reference the specific user manual for further directions. This bolt is sold individually and is an OEM replacement part. Note that some devices require more than one screw so be sure to purchase the correct amount.

This replacement part is a screw. This part is small but very useful in many kinds of machinery. This part connects components and ensures that they are secure.Screws may become stripped with overtightening, or corroded from exposure to the elements.This is a genuine replacement part made by Husqvarna. It is an OEM replacement part which will ensure a proper fit. This part is sold individually.

This flange nut can be used as a replacement part for snowblowers, lawnmowers, and tillers. Flange nuts fasten materials to one another in conjunction with a bolt. A flange nut is different from a regular nut in that it features a protruded flange on its end that functionally serves as a washer, negating the need for a separate washer part. A flange nut might have to be replaced for several reasons, including the part going missing, which is a frequent occurrence as it is small and does not necessarily cause any immediate damage if it is lost. Additionally, a flange nut can be subject to damage over time through general wear and tear, overuse, punctures, piercings, scrapes, or erosion to the metal material. Such damage can hamper its ability to fasten materials together. If this is the case, a replacement flange nut should be ordered. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This flange nut is a genuine OEM Husqvarna part, sold individually. It compatible with the following outdoor appliance brands: Husqvarna, Poulan, and Craftsman.

The replacement handle bolt here can be used for lawn and garden equipment. The handle bolt is used with the handle knob to help secure the upper and lower handles of the machine together. If the bolt is damaged or missing, it will not be possible to secure the handles properly. The handle bolts are durable and made from metal, but they could become damaged due to corrosion or natural wear. In other cases, they could become lost. In either case, they will need to be replaced. The replacement is simple and will not require any tools, as the square part of the bolt will fit into the handle perfectly. The handle knob will then be used to keep it in place. The handle bolt is a genuine OEM Part for lawn mowers and snowblowers. It is compatible with some models from Husqvarna, Murray, Weed Eater, Poulan, Jonsered, Craftsman, and Ryobi. It should be noted that this product is sold individually, and the handle knob is not included.

This O-ring is an OEM part sourced directly from the manufacturer, and it is sold individually. The manufacturer of this product is MTD. An O-ring is a small but important piece of hardware. It is designed for use with outdoor lawn and garden equipment including lawnmowers and string trimmers. It is compatible with products made by the following brands: Craftsman, Husqvarna, Weed Eater, Ryobi, Poulan, Murray, and Ariens.The design and purpose of the O-ring is relatively self-explanatory. It is an “O” shaped ring of material which is used as a gasket. It is designed to sit within a groove and be compressed during assembly. The reason for this is to create a perfect seal that blocks the path of liquids or gases from escaping or flowing into regions of the machine where they are not supposed to be.Replacing a damaged O-ring is crucial if the equipment is struggling to start. After checking the air filter cover, removing the carburetor, and cleaning it thoroughly, the next step is to replace the O-rings, carburetor gasket, and air filter, followed by the spark plug. Regular maintenance of the carburetor and routine evaluation of the suitability of the O-ring is essential to proper mechanical maintenance. This O-ring is made out of neoprene.

This piece is called a skirt bracket, and it will work with a range of mowers. The purpose of the bracket is to secure the grass deflector to the frame of the mower. If the bracket is not working properly or is broken, the deflector will not stay on the machine, and the grass and debris will not be deflected properly. Owners will want to replace the piece as soon as possible.The metal skirt brackets are durable but might still need to be replaced at some point. The brackets could become bent or damaged during the use of the mower, or when the mower is stored. They could break, or they could become corroded. Owners will find that the replacement is relatively easy and quick to do. They should remember to wear gloves to keep their hands safe.The skirt brackets will work with certain models from Husqvarna and Jonsered. The bracket is sold individually. This is a genuine OEM replacement part that has been sourced from the manufacturer.