Parts for Ge QNE27JYMXFFS: Freezer Door Parts

This freezer door gasket forms an airtight seal between the freezer door and cabinet. Replacing a worn seal helps keep cold air in, reduce frost and condensation, and support consistent freezer temperatures.

• Seals the door perimeter to prevent warm air leaks
• Helps maintain stable internal temperature and humidity
• Reduces frost/ice buildup and moisture around the opening
• Common symptoms of failure: torn or warped gasket, poor door seal, frost along edges, temperature fluctuations

• Unplug the refrigerator before starting; open the freezer door
• Warm the new gasket with warm water or a hair dryer on low to relax it for easier installation
• Seat the corners first, then press the gasket evenly into the channel/retainer and ensure uniform contact around the perimeter
• Perform a paper-slip test and allow the gasket to conform after closing the door for several hours

This bracket support is a small mounting bracket that secures and stabilizes appliance components, helping keep panels and assemblies aligned for proper operation and reduced vibration. It's a direct-fit replacement when the original bracket is broken or missing. What it does

• Provides a sturdy mounting point to hold panels or internal components in place
• Restores proper alignment to doors, panels or assemblies that sit on the bracket
• Reduces rattling or vibration caused by a loose or damaged bracket
• Helps prevent wear or damage from parts shifting during use

• Unplug the appliance and shut off water/gas (if applicable) before starting work
• Use the original mounting screws; replace damaged fasteners as needed
• Handle sharp sheet-metal edges carefully and wear gloves and eye protection

This is a 1/4-20 UNC machine screw used to fasten appliance components securely. It restores proper fit and stability where threaded fasteners are required, preventing loose panels or shifting parts. What it does:

• Secures panels, brackets, or assemblies that use a 1/4-20 UNC threaded hole
• Stops rattling or movement caused by a missing or damaged screw
• Restores correct mechanical connection for safe operation
• Useful when replacing stripped, corroded, or lost fasteners

• Disconnect power to the appliance before servicing.
• Start threads by hand to avoid cross-threading; tighten until snug.
• Do not overtighten — use appropriate torque for the material to avoid stripping threads or damaging parts.
• Ensure proper contact and secure fastening.

This replacement screw secures appliance brackets, panels, and components. It restores a tight, aligned fit when the original hardware is stripped, rusted, or missing, helping reduce vibration and rattling for reliable operation.

• Fastens brackets, panels, or mounts to keep components secure and aligned
• Replaces missing, stripped, or corroded hardware
• Helps reduce vibration, rattling, or loose/misaligned parts
• Matches original spec for reliable hold and fit

• Disconnect power before servicing; use proper PPE
• Match thread and length to the removed screw before installation
• Start threads by hand to prevent cross-threading; tighten until snug—do not overtighten
• Ensure parts are aligned and seating surfaces are clean before tightening

This drawer bracket secures and supports a refrigerator drawer, restoring proper alignment and smooth operation. Replace a broken or cracked bracket to prevent sagging drawers and ensure contents slide correctly. What it does:

• Supports the drawer assembly and keeps the drawer level during opening and closing
• Restores proper drawer alignment when original bracket is cracked or damaged
• Prevents drawer sagging or binding that can catch or stick
• Helps maintain smooth sliding and proper engagement with the drawer track

• One drawer bracket

• Designed for direct replacement; remove drawer and any trim to access mounting location
• Compare the part to the original before installation to confirm orientation and screw hole alignment
• Use appropriate hand tools; do not force the bracket to avoid cracking adjacent plastic parts
• Disconnect power only if accessing components where electrical parts could be disturbed

This drawer bracket secures and supports a refrigerator drawer, keeping it aligned and stable for smooth opening and closing. A direct-fit replacement that restores proper drawer function and prevents sagging or misalignment. What it does:

• Supports and stabilizes the drawer to maintain proper alignment
• Keeps the drawer track engaged for smooth sliding action
• Prevents the drawer from sagging or detaching when loaded
• Helps stop rattling or uneven movement caused by a damaged bracket

• Disconnect power to the appliance before beginning any repair
• Remove drawer contents and slide out the drawer to access the bracket area
• Inspect mounting points and hardware; replace any worn screws or clips as needed
• Tighten fasteners securely but avoid over-torquing to prevent damage

A short 8-32 x 3/8 hex washer head screw used to secure small appliance panels and components. Simple replacement for stripped or missing fasteners to restore proper fit and prevent rattles or loose parts. What it does:

• Secures panels, brackets, and small assemblies in place
• Helps eliminate vibration-related noise from loose parts
• Replaces missing, damaged, or corroded screws to restore proper alignment
• Fits standard 8-32 threaded holes requiring a 3/8" length screw

• One 8-32 x 3/8 hex washer head screw

• Use the correct 8-32 driver to avoid stripping the head
• Tighten snugly but avoid over-torquing to prevent thread damage
• Disconnect power and follow appliance safety procedures before accessing internal components
• Replace only like-for-like fasteners in load-bearing or safety-critical locations