Parts for Ge ZISB360DNFII: Freezer Door Parts

This is a #8-18 x 5/8 inch oval-head stainless steel screw used to secure panels and components on compatible GE appliances. It replaces missing or damaged fasteners to restore a secure fit and reduce vibration or rattling. What it does

• Secures trim, access panels, brackets or small components in place
• Restores proper alignment when a lost or stripped screw causes loose parts
• Helps eliminate rattling, vibration, or intermittent contact caused by missing fasteners
• Corrosion-resistant stainless finish for longer life in appliance environments

• Use the correct screwdriver or driver bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread damage or cracking nearby plastic
• Power tools can be used carefully on low torque settings
• Replace any stripped mating nuts or threaded inserts for secure fastening

This replacement freezer bottom hinge bushing helps the freezer door pivot smoothly and maintain proper alignment, reducing rubbing and uneven wear for more reliable closing. What it does:

• Provides a smooth pivot surface for the freezer bottom hinge
• Restores proper door alignment to help ensure a tight seal
• Reduces hinge noise, sticking, and rubbing during door movement
• Helps prevent premature wear of the hinge and door components

• One freezer bottom hinge bushing

• Disconnect power to the appliance and empty or support the door before starting
• Support the door while removing hinge fasteners to prevent falling or injury
• Inspect the hinge and shaft for wear; replace the hinge assembly if damaged
• Do not overtighten fasteners; test door operation after installation

This gasket and label assembly replaces a worn or damaged side-by-side refrigerator door seal and its attached label, restoring a proper seal to help maintain consistent cooling and reduce frost buildup. Fits the refrigerator door where original gasket is mounted. What it does:

• Seals the door perimeter to help keep cold air inside and warm air out.
• Helps reduce frost or ice buildup caused by a leaking or damaged seal.
• Addresses symptoms such as visible gaps around the door, excessive frost, or uneven temperatures inside the compartment.
• Includes the attached product/identification label as shipped from the manufacturer.

• Unplug the appliance before starting any work and remove food and door-mounted items.
• Replace the old gasket by loosening any retainer or screws, positioning the new gasket into the retainer, and securing per the service manual; do not force or stretch the gasket.
• After installation, check the door seal around the full perimeter and adjust the door alignment if needed; follow the manufacturer's service instructions for final seating.
• If retainers, clips, or screws are damaged or missing, order those parts separately.

Restore secure, organized door storage with this door bin assembly. It replaces a cracked or missing bin so bottles, jars, and condiments stay in place, easy to reach, and less likely to tip or spill.

• Creates a sturdy shelf on the door to hold jars, bottles, and condiments
• Common symptoms: cracked plastic, broken/loose mounting tabs, bin falls off or won't stay seated, missing bin
• Restores original door storage capacity and organization
• "36/42" denotes the manufacturer's designated bin style for those series; confirm fit by model

• Remove items from the old bin; lift the bin straight up to release from the door rails
• Allow cold plastic to warm to room temperature before handling to reduce cracking risk
• Align new bin on the molded door ribs/rails and press down until fully seated
• Verify a secure fit before reloading; avoid overloading the bin

This refrigerator freezer bottom door trim restores the finished lower edge of the freezer door, improving appearance and sealing against drafts. It replaces damaged or cracked trim to help keep the freezer looking and functioning properly. What it does:

• Covers and protects the lower exterior edge of the freezer door from chips, dents, and wear
• Helps maintain a tidy seal line where the door meets the cabinet, reducing visible gaps
• Restores the original finished appearance after impact or aging damage
• Matches the OEM shape so the door closes and aligns correctly

• One freezer bottom door trim piece

• Designed to install with existing factory fasteners; inspect clips and screws and replace if damaged
• Remove power to the appliance and work with the door in a stable, supported position
• Use trim-safe tools to pry or align the piece to avoid scratching the finish
• If metal mounting clips are bent or broken, source replacements before installing this trim

This handle trim cover replaces a worn or damaged door handle end cap to restore a clean, finished look and hide fasteners. It snaps or slides into place on the door handle for a neat appearance. What it does:

• Covers the exposed end of a refrigerator/freezer door handle for a finished appearance
• Hides screws and fasteners to improve aesthetics
• Helps keep dirt and moisture out of the handle cavity
• Suitable when trim is cracked, scratched, faded, or missing

• 1 handle trim cover

• Remove the existing trim or handle before installing
• Align trim with handle end and press or slide into place until it seats securely
• Use basic hand tools; avoid forcing parts to prevent damage
• Disconnect power or follow appliance safety guidance before servicing if applicable