Parts for Jenn-Air JBZFL24IGX10: Freezer Liner And Icemaker Parts

This fitting connects a flexible water or drain hose to the appliance, restoring a secure, leak-free connection. It's a small replacement part that prevents drips and keeps water flowing where it's needed. What it does:

• Joins a hose to the appliance inlet, outlet, or valve for a sealed connection
• Helps stop leaks at the hose connection point
• Restores proper water flow when a damaged or corroded fitting is replaced
• Works with the appliance hose system; commonly replaced when connections are loose or leaking

• Turn off and unplug the appliance and shut off the water supply before replacing the fitting
• Drain residual water from the hose or lines to avoid spills
• Hand-start threads, then tighten securely with appropriate tool; avoid over-tightening
• Inspect and replace any O-rings or gaskets if worn to ensure a watertight seal

This rubber grommet cushions and protects components where wiring, tubing or hardware pass through panels, helping reduce vibration and wear. Replace worn grommets to restore a snug, quiet fit and help prevent chafing. What it does:

• Cushions parts to reduce vibration and noise during operation
• Protects wires, hoses, and edges from abrasion where they pass through openings
• Keeps components aligned and helps maintain a secure fit
• Prevents metal-to-metal contact that can lead to premature wear

• Unplug the appliance or shut off power before beginning any repair
• Inspect the surrounding mounting area and replace any damaged fasteners or seals
• Pry out the old grommet carefully to avoid enlarging the opening; press the new grommet into place until fully seated

This damper controls airflow from the freezer to the fresh-food compartment to help maintain proper refrigerator temperatures. Replaces a worn or stuck damper to restore balanced cooling and reduce temperature swings. What it does:

• Regulates cold-air flow between freezer and refrigerator compartments.
• Helps maintain consistent fresh-food temperatures by opening and closing as needed.
• Common symptoms of a failing damper: warm fresh-food compartment, freezer overcooling, or temperature fluctuations.
• May produce unusual noises or fail to move if damaged or obstructed.

• Disconnect power to the appliance before beginning any repair.
• Access typically requires removing interior panels or the fresh-food evaporator cover; follow your model's service instructions.
• Handle clips and actuator components carefully to avoid breakage.

This thermistor is the refrigerator/freezer temperature sensor that helps the control board monitor and regulate internal temperatures for proper cooling. Replaces a failed sensor to restore accurate temperature sensing and stable operation. What it does:

• Measures internal air temperature so the control board can cycle cooling appropriately
• Commonly linked to symptoms like incorrect temperature readings, warm compartments, or too-frequent compressor cycles
• Helps prevent overcooling or excessive defrost cycles when operating correctly
• Works as part of the refrigerator's temperature control and defrost systems

• One thermistor sensor

• Disconnect power before accessing the appliance and working near electrical components
• Typically mounted in an evaporator well, door, or cabinet — handle the sensor and wiring gently to avoid damage
• May require removing interior panels or the evaporator cover for access; use basic hand tools

This replacement access cover protects internal appliance components and restores the appliance's exterior fit and appearance. It helps keep wiring and parts secure while reducing dust and debris entry for safer operation. What it does:

• Shields internal components and wiring from dust, debris and accidental contact
• Helps prevent noise from loose or exposed parts and improves cabinet fit
• Restores the appliance's exterior appearance after damage or removal
• Supports safe operation by covering service areas and component openings

• One replacement access cover

• Disconnect power (and water if applicable) before beginning any work
• Use basic hand tools; follow model-specific service instructions for removal and installation
• Handle edges carefully to avoid cuts and ensure cover is seated and fastened securely

This insul-sound deadening pad reduces vibration and noise by dampening panels and components in laundry and kitchen appliances. It's a small adhesive-backed sound/isolation pad used where noise or rattles transfer through metal surfaces. What it does

• Dampens rattles and reduces structure-borne noise from panels, cabinets and housings.
• Helps isolate vibrating components from appliance chassis to lower perceived sound.
• Commonly applied behind control panels, cabinet walls or on motor mounts to cut vibration transmission.
• Useful when worn, detached or hardened factory pads allow increased noise.

• One insul-sound deadening pad

• Disconnect power before servicing an appliance to avoid shock or injury.
• Clean and dry mounting surface; press pad firmly to ensure adhesive contact.
• Replace only in the original location; do not cover vents or moving parts.
• If adhesive is weak, use OEM-approved adhesive; avoid solvents that may damage finishes.

This cover is the OEM-style housing piece that protects and conceals internal components, restoring a finished appearance and helping keep wiring and parts free from debris. What it does:

• Covers and protects internal components from dust, lint, and accidental contact
• Restores the appliance's exterior appearance when the original cover is cracked or missing
• Prevents loose parts from rattling and reduces risk of snagging wiring or components
• Helps maintain airflow paths and component placement by holding parts in position

• One cover

• Disconnect power (unplug appliance or shut off breaker) before servicing
• Remove any retaining screws or fasteners; keep hardware for reinstallation
• Handle edges carefully—metal or plastic parts may have sharp edges
• Test operation only after cover and all fasteners are fully reinstalled