Parts for Maytag MFI2570FEB09: Freezer Liner Parts

The Shaft is an OEM part for Whirlpool refrigerators. This component serves as the axle for the refrigerator's wheels, allowing for smooth movement when repositioning or cleaning the appliance. It is designed to fit securely and ensure stability during use. The shaft's approximate length is 26 inches.

Common causes of a bad wheel shaft include excessive weight, rough handling during relocation, or wear and tear over time.

Symptoms of a bad wheel shaft include:

• Difficulty moving the refrigerator
• Unstable or wobbly positioning
• Visible bending or damage to the shaft
• Unusual noises when moving the appliance

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This right-hand slide bracket secures and supports a cabinet or drawer slide assembly so drawers and shelves open and close smoothly. It restores alignment and support for proper sliding action. What it does:

• Anchors the right-side slide or rail to the cabinet frame or drawer assembly
• Keeps the slide aligned to prevent binding, sagging, or uneven travel
• Helps restore smooth opening and closing when the drawer or shelf sticks
• Works with the existing slide/rail hardware; replaces damaged or broken brackets

• One right-hand slide bracket

• Turn off power to any nearby powered components and remove contents before starting
• Remove the drawer or shelf to access the bracket
• Typical installation requires basic hand tools (screwdriver or nut driver) and original fasteners; retain screws for reuse unless replacement is specified
• Inspect mating slide/rail and adjacent brackets for wear and replace any damaged components to ensure proper function

This left-side slide bracket secures and guides a sliding assembly so drawers or components open smoothly and stay aligned. It replaces a worn or broken bracket to restore proper support and reduce binding or sagging. What it does:

• Provides structural support for the left side of a sliding drawer/assembly
• Keeps slides aligned so the drawer opens and closes smoothly
• Helps stop sagging, catching, or uneven movement of the sliding part
• Replaces cracked, bent, or damaged brackets that interfere with operation

• Disconnect power and/or unplug the appliance before starting any repair
• Remove any outer panels or drawer components as needed to access the bracket
• Keep original fasteners; install bracket in the same orientation and tighten screws securely but do not overtighten
• If movement still feels restricted after replacement, check mating slide components and alignment

This right-hand side adapter bracket secures and aligns the appliance's panel or component so doors and panels fit properly and move smoothly. It replaces a worn or damaged bracket to restore correct panel positioning and support. What it does:

• Provides a mounting point and alignment for the right-hand side panel or assembly
• Helps prevent panel misalignment, rubbing, or sagging that can affect fit and seal
• Restores secure attachment after impact, corrosion, or hardware failure
• Compatible with the factory mounting location and fastener points per OEM design

• One right-hand side adapter bracket

• Designed for direct replacement—remove trim/panel fasteners to access the bracket
• Use appropriate hand tools; keep track of original fasteners for reuse if undamaged
• Disconnect power or follow appliance-specific safety procedures before service

This left-hand adapter bracket secures and aligns the appliance's left-side components to restore proper fit and function. It provides a durable mounting point for panels or assemblies that rely on a stable bracket. What it does:

• Replaces a worn or broken left-side adapter/bracket that can cause loose or misaligned panels
• Restores proper panel alignment and reduces rattling or vibration during operation
• Helps maintain correct spacing for adjacent parts that rely on the left-side mount
• Works as the structural mounting point for the left-side assembly it supports

• Disconnect power (and gas if applicable) before starting any repair
• Installation typically requires basic hand tools (screwdriver, socket set); keep fasteners organized
• Handle edges carefully to avoid cuts and ensure the bracket seats fully before tightening

The Evaporator Fan Grommet is an OEM component specifically designed for Whirlpool refrigerators. Found along the rear wall of the fridge compartment where the evaporator fan motor is located, the evaporator fan grommet serves an important sealing function.

Constructed of flexible rubber, the evaporator fan grommet forms a tight, airtight seal around the electrical wiring harness and ventilation ductwork attached to the rear-mounted evaporator fan motor. This helps prevent the escape of cold air from the refrigeration system and allows the evaporator fan motor to work efficiently. 

Causes of a bad evaporator fan grommet include cracks or splits from vibration stress over years of use. Dried-out seals no longer achieving a tight fit is also possible. 

Symptoms of a bad evaporator fan grommet include:

• Cold air leaking from around the rear wall area  
• Increased humidity inside the fridge compartment
• Decreased cooling performance efficiency

Compatible with Whirlpool, KitchenAid, Jenn-Air, and select Kenmore side-by-side models.

This evaporator fan motor circulates cold air across the evaporator coil so your refrigerator can maintain even temperatures and proper cooling. Replacing a failing motor restores airflow and helps prevent warm spots. What it does:

• Spins the freezer evaporator fan to move cold air through the evaporator and into the cabinet
• Restores airflow when a worn motor causes weak airflow or no fan movement
• Helps correct uneven cooling or warmer-than-normal freezer and refrigerator compartments
• Can reduce abnormal humming or buzzing from the freezer when the motor is failing

• Always disconnect power before accessing the freezer evaporator compartment
• Remove interior panels and the evaporator cover to reach the motor; keep screws and fasteners organized
• Handle the evaporator coil and fan blade carefully to avoid damage or bending fins
• Reconnect wiring harness and secure motor per original mounting; test operation before reassembling all panels

A molded defrost drain funnel that routes condensation and melted frost into the refrigerator's drain to help prevent pooling and interior leaks. Replaces cracked or clogged funnels to restore proper water flow in the drain path. What it does

• Guides defrost and condensation water from the evaporator area into the fridge drain system.
• Helps prevent water pooling inside the fresh-food or freezer compartments.
• Worn, cracked or clogged funnels can cause dripping, pooling or frost build-up near the evaporator.
• Restores a secure, directed path for meltwater to reach the drain tube and pan.

• Disconnect power to the appliance before accessing internal components to reduce shock risk.
• Remove food and any removable shelving to access the evaporator/drain area; handle plastic trim carefully to avoid breakage.
• Inspect surrounding drain area for ice, debris or clogs and clear before reinstalling the funnel.
• If clips or screws secure the funnel, retain hardware and reinstall securely; test a small amount of water to ensure proper drainage.