Parts for Ge ETS22SBSCRSS: 02 - Fresh Food Door Parts

A stainless-steel handle fastener that secures the refrigerator door handle to the door assembly for a solid, wobble-free grip. Use to restore a loose, stripped, or missing handle attachment point. What it does:

• Secures the door handle to the door/handle mounting point so the handle stays tight and aligned.
• Stops handle movement, wobbling, or rattling caused by a worn or missing fastener.
• Replaces a corroded or damaged fastener to restore a secure connection.
• Stainless finish resists corrosion at the handle mounting point.

• Disconnect power to the appliance before starting work whenever access to internal parts is required.
• Use the correct screwdriver or bit; turn carefully and avoid sideways force on the handle.
• Do not overtighten—over-torquing can strip threads or crack surrounding trim.
• Keep removed hardware and any trim pieces for reassembly; inspect handle and threaded inserts for damage.

This fresh food door gasket creates an airtight seal around the refrigerator compartment door to prevent air leaks. Replacing a worn seal helps maintain stable temperatures, reduce moisture at the door, and restore proper closing and sealing.

• Creates a tight seal around the fresh food door to prevent air infiltration
• Helps maintain consistent temperatures and minimize condensation at the door
• Wear indicators include cracks, tears, warping, or visible gaps in the seal
• Common symptoms: door not sealing well, warm spots in the fridge, or longer run times

• Disconnect power before servicing
• Remove the old gasket and clean the door's gasket channel/retainer
• Warm the new gasket in clean warm water to relax folds; start at corners and press the lip fully into the channel without stretching
• Close the door and check for uniform contact; adjust hinges/strike if needed and allow up to 24 hours for the gasket to fully conform

This module shelf provides a stable mounting surface for the refrigerator control module, keeping wiring and electronics secure and organized for reliable operation. It helps prevent movement and abrasion that can cause intermittent faults. What it does:

• Secures the control module and related wiring to the refrigerator cabinet
• Helps protect electronic components from vibration and contact damage
• Keeps module positioned for proper connections to sensors and harnesses
• Can reduce intermittent electrical faults caused by loose or chafing components

• One module shelf 22 (single shelf)

• Disconnect power to the appliance before starting any repair to avoid shock or damage
• Handle the control module and wiring carefully to avoid static or physical damage
• Use the existing mounting hardware and follow the appliance service instructions for correct placement

A replacement reversible plug door that covers and protects the appliance power inlet while letting the cord exit left or right for tidy cord routing. Restores a clean back panel appearance and helps keep the power connection protected from debris. What it does:

• Covers the power inlet opening to protect the plug and inlet from dust and debris.
• Reversible design lets you route the power cord to either side to fit against the wall.
• Helps keep the cord tucked close to the appliance so the unit can sit flush with cabinetry or walls.
• Replace when the door is cracked, broken, missing, or no longer holds the plug securely.

• Always unplug the appliance before starting any repair or inspection.
• May require access to the rear panel; check your owner's manual for disassembly steps.
• Check orientation before finalizing installation to ensure correct left/right cord routing.

This replacement screw fastens refrigerator components securely, restoring a tight, rattle-free fit when original hardware is missing, stripped, or corroded. Use it to secure panels, brackets, or trim and keep parts properly aligned.

• Secures panels, brackets, covers, or trim in place
• Helps maintain correct alignment of components and hardware
• Reduces vibration and rattling caused by loose or missing screws
• Replaces lost, rusted, or stripped screws

• Unplug the refrigerator and turn off water supply if working near water components
• Match thread and length to the removed fastener; hand-start threads to avoid cross-threading
• Tighten snugly; do not overtighten into plastic or thin sheet metal
• Keep track of any spacers or washers reused from the original assembly