Parts for Ge PTS22LCSARCC: 02 - Fresh Food Door Parts

This is the magnetic door gasket that seals the fresh food compartment, keeping cold air in and warm air out to maintain temperature and reduce frost and energy loss.

• Creates an airtight seal around the refrigerator (fresh food) door
• Helps maintain proper internal temperature and humidity
• Worn, torn, warped, or hardened gaskets can cause warm spots, sweating/condensation, or excessive run time
• Replace if the door won't seal, you see gaps/light around the door, or the gasket is cracked or misshapen

• Unplug the appliance before servicing
• Soften the new gasket in warm water or with gentle heat to improve flexibility
• Remove the old gasket from the door channel; press the new gasket fully into the groove, working evenly around the perimeter
• Check door alignment and perform a "paper test" to confirm a uniform seal

This replacement module shelf insert restores the shelf support that holds the refrigerator control module area and helps keep the shelf level and components secure. Fits into the module shelf to replace broken or missing inserts. What it does:

• Secures the control/module area so the module and wiring stay in place and out of direct contact with stored items
• Restores proper shelf alignment to prevent sagging or uneven loading
• Reduces rattling or noise caused by a loose or damaged shelf insert
• Helps protect the module area from minor impacts or shifting contents

• Disconnect power to the appliance before servicing to avoid electric shock.
• Remove the shelf or access panel per your owner's manual for clear access to the module shelf area.
• Snap or press the new insert into the designated slot until it seats firmly; verify fit and alignment.

This reversible door plug covers the unused hinge or mounting hole after changing a door swing, restoring a clean appearance and helping keep out dirt and drafts. Simple, color-matched replacement for a neat finish. What it does:

• Covers exposed hinge or mounting holes on the door edge for a finished look
• Helps block dust, pests and drafts from entering through unused openings
• Matches original geometry to sit flush with the door surface
• Designed to work with reversible door installations where a hole is no longer used

• One (1) reversible door plug

• No tools are typically required; press plug into the unused hole until it seats securely
• Confirm correct orientation before installing to ensure a flush fit
• Inspect surrounding sealing surfaces and clean area before installation
• If plug is damaged or does not seat properly, replace with the exact part number

This fixed module shelf holds and secures the refrigerator control module or electronic components in place, restoring proper support and alignment. It's a direct-replacement shelf designed to fit the original mounting points. What it does:

• Provides a stable mounting surface for the control module or electronic assembly
• Prevents module movement that can cause loose connections or intermittent operation
• Helps maintain proper spacing and airflow around the module for reliable performance
• Addresses symptoms such as rattling or a loose control module behind the interior panel

• Installation requires removing the interior panel or cover to access the module area; follow your model's service manual
• Handle electronic components carefully and disconnect power before starting work to avoid shock or damage
• Use original mounting screws or hardware; only tighten to secure without over-torquing

This module snugger is a small retaining piece used in the refrigerator to hold its associated module or component securely in place. Replacing a cracked or missing snugger restores a tight fit, reduces vibration and noise, and supports correct operation.

• Secures the related module or assembly to prevent shifting
• Helps maintain proper alignment for reliable performance
• Reduces rattles and wear from vibration or movement
• Typical signs it's needed: part is broken or missing, components feel loose, or you hear rattling

• Disconnect power to the refrigerator before servicing
• Note the original orientation and location; take a photo for reference
• Reuse existing fasteners or clips if applicable; avoid overtightening
• After installation, confirm the part holds the assembly firmly and that movement is smooth where intended

This replacement screw fastens refrigerator components securely, restoring a tight, rattle-free fit when original hardware is missing, stripped, or corroded. Use it to secure panels, brackets, or trim and keep parts properly aligned.

• Secures panels, brackets, covers, or trim in place
• Helps maintain correct alignment of components and hardware
• Reduces vibration and rattling caused by loose or missing screws
• Replaces lost, rusted, or stripped screws

• Unplug the refrigerator and turn off water supply if working near water components
• Match thread and length to the removed fastener; hand-start threads to avoid cross-threading
• Tighten snugly; do not overtighten into plastic or thin sheet metal
• Keep track of any spacers or washers reused from the original assembly