Parts for Ge PTS22LCSARWW: 02 - Fresh Food Door Parts

This is the magnetic door gasket that seals the fresh food compartment, keeping cold air in and warm air out to maintain temperature and reduce frost and energy loss.

• Creates an airtight seal around the refrigerator (fresh food) door
• Helps maintain proper internal temperature and humidity
• Worn, torn, warped, or hardened gaskets can cause warm spots, sweating/condensation, or excessive run time
• Replace if the door won't seal, you see gaps/light around the door, or the gasket is cracked or misshapen

• Unplug the appliance before servicing
• Soften the new gasket in warm water or with gentle heat to improve flexibility
• Remove the old gasket from the door channel; press the new gasket fully into the groove, working evenly around the perimeter
• Check door alignment and perform a "paper test" to confirm a uniform seal

This thimble door top is the white trim piece that covers and protects the upper edge of the appliance thimble/dryer vent opening, restoring a finished look and helping keep the seal area intact. What it does:

• Replaces a cracked, chipped or warped top trim to improve appearance and fit
• Helps keep the vent/thimble opening properly covered and aligned
• Protects the upper edge of the opening from wear and impacts
• Prevents gaps that can allow lint or debris accumulation around the opening

• Disconnect power to the appliance before beginning any repair
• Use basic hand tools; hold parts securely to avoid scratching surrounding surfaces
• Inspect mating surfaces and remove lint/debris before installing for proper fit

This replacement module shelf insert restores the shelf support that holds the refrigerator control module area and helps keep the shelf level and components secure. Fits into the module shelf to replace broken or missing inserts. What it does:

• Secures the control/module area so the module and wiring stay in place and out of direct contact with stored items
• Restores proper shelf alignment to prevent sagging or uneven loading
• Reduces rattling or noise caused by a loose or damaged shelf insert
• Helps protect the module area from minor impacts or shifting contents

• Disconnect power to the appliance before servicing to avoid electric shock.
• Remove the shelf or access panel per your owner's manual for clear access to the module shelf area.
• Snap or press the new insert into the designated slot until it seats firmly; verify fit and alignment.

This reversible door plug fills the unused mounting hole when you switch the door swing on your refrigerator. It restores a finished appearance and helps keep air and moisture from entering through the opening.

• Covers the unused door hole created during a door swing reversal
• Helps maintain proper sealing and resists drafts/condensation at the opening
• Restores a clean, finished, factory look to the door
• Common symptoms: missing or cracked plug, exposed hole, cosmetic gap on door edge

• Disconnect power before servicing any door components
• Gently pry out the old plug with a plastic trim tool to avoid scratches
• Align the new plug with the opening and press until fully seated and flush
• Verify the door closes properly and the gasket seals evenly

This fixed module shelf holds and secures the refrigerator control module or electronic components in place, restoring proper support and alignment. It's a direct-replacement shelf designed to fit the original mounting points. What it does:

• Provides a stable mounting surface for the control module or electronic assembly
• Prevents module movement that can cause loose connections or intermittent operation
• Helps maintain proper spacing and airflow around the module for reliable performance
• Addresses symptoms such as rattling or a loose control module behind the interior panel

• Installation requires removing the interior panel or cover to access the module area; follow your model's service manual
• Handle electronic components carefully and disconnect power before starting work to avoid shock or damage
• Use original mounting screws or hardware; only tighten to secure without over-torquing

This module snugger is a small retaining piece used in the refrigerator to hold its associated module or component securely in place. Replacing a cracked or missing snugger restores a tight fit, reduces vibration and noise, and supports correct operation.

• Secures the related module or assembly to prevent shifting
• Helps maintain proper alignment for reliable performance
• Reduces rattles and wear from vibration or movement
• Typical signs it's needed: part is broken or missing, components feel loose, or you hear rattling

• Disconnect power to the refrigerator before servicing
• Note the original orientation and location; take a photo for reference
• Reuse existing fasteners or clips if applicable; avoid overtightening
• After installation, confirm the part holds the assembly firmly and that movement is smooth where intended

This replacement screw fastens refrigerator components securely, restoring a tight, rattle-free fit when original hardware is missing, stripped, or corroded. Use it to secure panels, brackets, or trim and keep parts properly aligned.

• Secures panels, brackets, covers, or trim in place
• Helps maintain correct alignment of components and hardware
• Reduces vibration and rattling caused by loose or missing screws
• Replaces lost, rusted, or stripped screws

• Unplug the refrigerator and turn off water supply if working near water components
• Match thread and length to the removed fastener; hand-start threads to avoid cross-threading
• Tighten snugly; do not overtighten into plastic or thin sheet metal
• Keep track of any spacers or washers reused from the original assembly