Parts for Ge PTS25LHRARBB: 02 - Fresh Food Door Parts

The GE refrigerator water filter is an OEM replacement part responsible for ensuring the quality of the water dispensed on GE Profile top and bottom freezer refrigerators. It is responsible for purifying the water before it reaches your glass or ice maker, providing you with clean and safe drinking water directly from your refrigerator. To maintain optimal water quality and ensure the filter's effectiveness, it is recommended to replace the filter every 6 months or when the rated capacity of 750 gallons is reached.

Over time, the water filter can become clogged with sediment, reducing its effectiveness. Regular use and the accumulation of minerals and contaminants can lead to the need for replacement.

Symptoms of a bad water filter include:

• Reduced water flow from the dispenser
• Ice cubes with an unusual taste or odor
• The filter indicator light staying on
• Visible particles in the water or ice

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models. For the best performance, it is recommended to replace the water filter every six months or as indicated by the filter change light on your refrigerator.

This small door handle assembly (22 in) replaces a damaged or worn refrigerator/freezer door pull to restore a secure grip and smooth opening. Fits inline with factory trim for a clean, original appearance. What it does:

• Replaces a broken, cracked or missing small door handle to restore safe gripping and door access.
• Stops wobbling or loose handles that affect door opening and closing.
• Matches factory trim finish to maintain original look and feel.

• Disconnect power and empty the door area before beginning any repair.
• Remove retaining screws or clips from the inner door panel to access the handle fasteners.
• Align handle to mounting holes, then secure with the original hardware; do not overtighten to avoid cracking.

This small door handle assembly (22 in) replaces a damaged or worn refrigerator/freezer door pull to restore a secure grip and smooth opening. Fits inline with factory trim for a clean, original appearance. What it does:

• Replaces a broken, cracked or missing small door handle to restore safe gripping and door access.
• Stops wobbling or loose handles that affect door opening and closing.
• Matches factory trim finish to maintain original look and feel.

• Disconnect power and empty the door area before beginning any repair.
• Remove retaining screws or clips from the inner door panel to access the handle fasteners.
• Align handle to mounting holes, then secure with the original hardware; do not overtighten to avoid cracking.

The Screw Package is an OEM replacement part for GE refrigerators. It contains a pack of 12 identical screws for miscellaneous securing and assembly needs.

These screws play a supporting role, helping attach shelf tracks, cover panels, door hinges, and other interior parts. By maintaining components securely in place, they help ensure smooth operation and prevent rattling or other noises. 

Symptoms of insufficiently secured parts include:

• Noises heard from loose shelves or door components  
• Detaching handles, hinges, or panels
• Shelves shifting positions or becoming misaligned

Causes of needing replacement screws can include loss, stripping, or wear over time from repeated securement and removal of parts during cleaning or repairs. 

This multipack of GE screws is perfect for minor refrigerator maintenance or to stock up on extras. They are also compatible with replacement hardware from Hotpoint, RCA, and certain Kenmore models. 

This door gasket seals the freezer compartment to maintain proper temperature and energy efficiency. A direct-fit replacement that helps restore a full door seal and reduce frost build-up when the original gasket is damaged or worn. What it does:

• Creates an airtight seal around the freezer door to help keep cold air in and warm air out
• Helps reduce frost buildup and prevents temperature fluctuation inside the compartment
• Improves cooling performance and can reduce energy loss caused by a leaking seal
• Fits the factory door opening shape to ensure even compression and contact

• One door gasket (black), single-piece as shown

• Remove the old gasket and clean the door channel before installing the new gasket
• Seat gasket evenly around the door; warm with a hair dryer (low) if needed to help form and set the seal
• Check for proper door alignment and full contact after installation; adjust hinges if necessary
• Unplug the appliance or disconnect power before performing any repair

A replacement white door gasket that seals the refrigerator/freezer door to help maintain proper temperature and reduce energy loss. Fits compatible GE refrigerators that use part number WR24X10088. What it does:

• Replaces a worn or torn door gasket to restore a tight seal around the door
• Helps prevent warm air infiltration that can cause frost build-up and higher energy use
• Can reduce moisture and food spoilage caused by poor door sealing
• Useful when the existing gasket is cracked, split, flattened, or no longer seals evenly

• Inspect mounting channel and door surface for debris before installing; clean with mild detergent and water and dry fully
• Gasket typically presses into a retainer channel; align corners and seat evenly to avoid gaps
• Allow time for the gasket to relax into place; gentle warming can help fit—do not use open flame or excessive heat

This thimble door top is the white trim piece that covers and protects the upper edge of the appliance thimble/dryer vent opening, restoring a finished look and helping keep the seal area intact. What it does:

• Replaces a cracked, chipped or warped top trim to improve appearance and fit
• Helps keep the vent/thimble opening properly covered and aligned
• Protects the upper edge of the opening from wear and impacts
• Prevents gaps that can allow lint or debris accumulation around the opening

• Disconnect power to the appliance before beginning any repair
• Use basic hand tools; hold parts securely to avoid scratching surrounding surfaces
• Inspect mating surfaces and remove lint/debris before installing for proper fit

This module snugger is a small retaining piece used in the refrigerator to hold its associated module or component securely in place. Replacing a cracked or missing snugger restores a tight fit, reduces vibration and noise, and supports correct operation.

• Secures the related module or assembly to prevent shifting
• Helps maintain proper alignment for reliable performance
• Reduces rattles and wear from vibration or movement
• Typical signs it's needed: part is broken or missing, components feel loose, or you hear rattling

• Disconnect power to the refrigerator before servicing
• Note the original orientation and location; take a photo for reference
• Reuse existing fasteners or clips if applicable; avoid overtightening
• After installation, confirm the part holds the assembly firmly and that movement is smooth where intended

This reversible door plug covers the unused hinge or mounting hole after changing a door swing, restoring a clean appearance and helping keep out dirt and drafts. Simple, color-matched replacement for a neat finish. What it does:

• Covers exposed hinge or mounting holes on the door edge for a finished look
• Helps block dust, pests and drafts from entering through unused openings
• Matches original geometry to sit flush with the door surface
• Designed to work with reversible door installations where a hole is no longer used

• One (1) reversible door plug

• No tools are typically required; press plug into the unused hole until it seats securely
• Confirm correct orientation before installing to ensure a flush fit
• Inspect surrounding sealing surfaces and clean area before installation
• If plug is damaged or does not seat properly, replace with the exact part number

A replacement reversible plug door that covers and protects the appliance power inlet while letting the cord exit left or right for tidy cord routing. Restores a clean back panel appearance and helps keep the power connection protected from debris. What it does:

• Covers the power inlet opening to protect the plug and inlet from dust and debris.
• Reversible design lets you route the power cord to either side to fit against the wall.
• Helps keep the cord tucked close to the appliance so the unit can sit flush with cabinetry or walls.
• Replace when the door is cracked, broken, missing, or no longer holds the plug securely.

• Always unplug the appliance before starting any repair or inspection.
• May require access to the rear panel; check your owner's manual for disassembly steps.
• Check orientation before finalizing installation to ensure correct left/right cord routing.

This reversible door plug fills the unused mounting hole when you switch the door swing on your refrigerator. It restores a finished appearance and helps keep air and moisture from entering through the opening.

• Covers the unused door hole created during a door swing reversal
• Helps maintain proper sealing and resists drafts/condensation at the opening
• Restores a clean, finished, factory look to the door
• Common symptoms: missing or cracked plug, exposed hole, cosmetic gap on door edge

• Disconnect power before servicing any door components
• Gently pry out the old plug with a plastic trim tool to avoid scratches
• Align the new plug with the opening and press until fully seated and flush
• Verify the door closes properly and the gasket seals evenly

This replacement screw fastens refrigerator components securely, restoring a tight, rattle-free fit when original hardware is missing, stripped, or corroded. Use it to secure panels, brackets, or trim and keep parts properly aligned.

• Secures panels, brackets, covers, or trim in place
• Helps maintain correct alignment of components and hardware
• Reduces vibration and rattling caused by loose or missing screws
• Replaces lost, rusted, or stripped screws

• Unplug the refrigerator and turn off water supply if working near water components
• Match thread and length to the removed fastener; hand-start threads to avoid cross-threading
• Tighten snugly; do not overtighten into plastic or thin sheet metal
• Keep track of any spacers or washers reused from the original assembly